Data Sheet

5
SPECIFICATIONS
Function Range
2)
Frequency Range Resolution Accuracy (one year;
23°C ± 5°C)
True-RMS
AC Voltage
3)
600 mV
20 Hz – 45 Hz 0.01 mV 2.0 + 20
45 Hz – 100 Hz 0.01 mV 0.6 +10
100 Hz – 20 KHz 0.01 mV 0.2 + 10
20 KHz – 50 KHz 0.01 mV 1.0 + 10
50 KHz –100 KHz 0.01 mV 3.0 + 10
6 V
20 Hz – 45 Hz 0.0001 V 2.0 + 20
45 Hz – 100 Hz 0.0001 V 0.6 + 10
100 Hz – 20 KHz 0.0001 V 0.2 + 10
20 KHz – 50 KHz 0.0001 V 1.0 + 10
50 KHz –100 KHz 0.0001 V 3.0 + 10
60 V
20 Hz – 45 Hz 0.001 V 2.0 + 20
45 Hz – 100 Hz 0.001 V 0.6 +10
100 Hz – 20 KHz 0.001 V 0.2 + 10
20 KHz – 50 KHz 0.001 V 1.0 + 10
50 KHz –100 KHz 0.001 V 3.0 + 10
600 V
20 Hz – 45 Hz 0.01 V 2.0 + 20
45 Hz – 100 Hz 0.01 V 0.6 + 10
100 Hz – 20 KHz 0.01 V 0.2 + 10
20 KHz – 50 KHz 0.01 V 1.0 + 10
50 KHz –100 KHz 0.01 V 3.0 + 10
750 V
20 Hz – 45 Hz 0.01 V 2.0 + 20
45 Hz – 100 Hz[4] 0.01 V 0.6 + 10
100 Hz – 20 KHz 0.01 V 0.2 + 10
20 KHz – 50 KHz 0.01 V 1.0 + 10
50 KHz –100 KHz 0.01 V 3.0 + 10
True-RMS
AC Current
5)
60 mA
20 Hz – 45 Hz 0.001 mA 2.0 + 20
45 Hz – 2 KHz 0.001 mA 0.5 + 20
2 KHz – 10 KHz 0.001 mA 2.5 + 30
600 mA
20 Hz – 45 Hz 0.01 mA 2.0 + 20
45 Hz – 2 KHz 0.01 mA 0.5 + 20
2 KHz – 10 KHz 0.01 mA 2.5 + 30
6 A
20 Hz – 45 Hz 0.0001 A 2.0 + 20
45 Hz – 2 KHz 0.0001 A 0.5 + 20
2 KHz – 10 KHz 0.0001 A 2.5 + 20
10 A
6)
20 Hz – 45 Hz 0.001 A 1.5 + 15
45 Hz – 2 KHz 0.001 A 0.5 + 15
2 KHz – 10 KHz 0.001 A 2.5 + 25
AC Characteristic Accuracy ± (% of Reading + count)
1)
Additional wave crest factor error (not Sine)
7)
Wave crest coefcient Error (% Range)
1 – 2 0.05
2 – 3 0.3
Remarks:
1)
Specications are for 0.5 Hour warm-up, “Slow” measurement rate and calibration temperature 18°C ~ 28°C.
2)
10 % over range on all ranges except for DCV 1000 V, ACV 750 V, DCI 10 A and ACI 10 A.
3)
Specications are for amplitude of sine wave input > 5 % of range. For inputs from 1% to 5 % of range and < 50 kHz, add 0.1% of range as extra error.
For 50 kHz to 100 kHz, add 0.1% of range as extra error.
4)
Plus 0.025 V of error per 1 V after the rst ± 400 VAC.
5)
Specications are for sine wave input > 5 % of range. 0.1% error will be added when the range of the input sine wave is 1% to 5 %.
6)
30 seconds OFF/30 seconds ON is recommend for the continuous current higher than DC 7 A or AC RMS 7 A.
7)
For input Frequency Range < 100 Hz