P R O B E S A N D P R O B E A C C E S S O R I E S D11000PS DIFFERENTIAL PROBE SYSTEM The D11000PS extends the full signal acquisition performance of the SDA 11000 and SDA 9000 to the probe tips. With 11 GHz system bandwidth, the probe enables direct measurement of high-speed serial data streams up to 6.25 Gb/s. The D11000PS also provides 11 GHz system bandwidth when used with the SDA 18000.
P R O B E S A N D P R O B E A C C E S S O R I E S D11000PS DIFFERENTIAL PROBE SYSTEM Reproducing accurate serial data eye patterns requires maintaining precise magnitude and phase relationships between the fundamental and the odd harmonics. The advanced calibration system used in the D11000PS assures the best eye pattern fidelity. Superior Probe Loading Characteristics Accurate frequency response is not enough to assure good waveform fidelity. Excessive probe loading can cause waveform distortion.
P R O B E S A N D P R O B E A C C E S S O R I E S D11000PS DIFFERENTIAL PROBE SYSTEM Compatibility The D11000PS is designed specifically for use with the SDA 11000, SDA 9000, or SDA 18000. However, it does contain additional calibration data for use with all of the lower bandwidth WaveMaster, SDA, and DDA 5005A Series oscilloscopes and analyzers.
P R O B E S A N D P R O B E A C C E S S O R I E S D11000PS DIFFERENTIAL PROBE SYSTEM D11000PS Includes: Probe amplifier modules (2–1 each for SMA input and Solder-In lead), Solder-In lead assembly (2), SMA interconnect lead, SMA input cables (matched pair), Probe body, SMA DC blocking adapters (2), ground lead and clip, SMA finger wrench (2), tip retaining clip kit for Solder-In lead, probe body mounting clamp set, FreeHand probe stand, ESD dissipating wrist strap, SAC-01 soft accessory case with insert,
P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES WaveLink high bandwidth differential probes are designed to provide an optimum mechanical connection for signal measurement. They virtually eliminate distortion when measuring signals, which is particularly useful in eye pattern measurements— now routine for systems using fast serial data bus architecture. WaveLink probes provide industry-leading technology for wideband signal connection to test instruments.
P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES FLEXIBLE INTERCONNECTION OPTIONS —WITHOUT SACRIFICING PERFORMANCE D500PT Positioner Mounted Probe Tip Module The probe has a very thin form factor, allowing multiple probes to be used when several channels are required to monitor signals from the same small IC.
P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES THREE DIFFERENT TIPS FOR INTERCONNECT FLEXIBILITY Solder-In Lead The Solder-In interconnect lead features the smallest physical tip size of any high bandwidth differential probe and the highest level of electrical performance. Two very small damping resistors are directly soldered into the connect points providing a reliable, intermittent free electrical connection.
P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES SPECIFICATIONS Rise Time, probe only D600A-AT D600ST-SI D500PT D300A-AT D350ST-SP LF Attenuation Accuracy (with 0 V common mode) < 70 ps* < 65 ps* < 100 ps† < 95 ps‡ < 90 ps‡ D600A-AT, D300A-AT, D600ST, and D500PT 2% 0 ±1.2 V 5% ±1.2 V ±2.4 V D350ST 2% 0 ±2.5 V 5% ±2.
P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES SPECIFICATIONS (CONTINUED) CMRR D600A-AT DC to 1 GHz 1 GHz to 3 GHz 3 GHz to 7 GHz D600ST DC to 1 GHz 1 GHz to 3 GHz 3 GHz to 7 GHz D500PT DC to 1 GHz 1 GHz to 3 GHz 3 GHz to 5 GHz D350ST DC to 1 GHz 1 GHz to 3 GHz D300A-AT DC to 1 GHz 1 GHz to 3 GHz Noise > 40 dB > 30 dB > 20 dB > 30 dB > 25 dB > 20 dB > 25 dB > 19 dB > 16 dB > 30 dB > 25 dB > 40 dB > 30 dB D600A-AT, D600ST, D500PT 5.
P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES ORDERING INFORMATION (CONTINUED) CONSUMABLES AND REPLACEMENT PARTS Replacement Quick Connect Lead Set for D600ST Replacement Solder-In Lead Set for D600ST Replacement Square Pin Lead Set for D600ST Extra Solder-In Lead for D350ST Extra Square Pin Lead for D350ST Replacement Tip Assembly for D500PT Replacement Resistor Kit for D600ST-SI (10) Replacement Resistor Kit for D600ST-QC (20) Replacement Probe Tip Holder Kit Replacement
P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBES Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400 V, some as high as 600 V.
P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES WAVELINK PROBE COMPATIBILITY CHART D600A-AT D300A-AT D600ST D350ST D500 PT WL600 WL300 SDA 18000* SDA 11000* SDA 9000* SDA 6020 SDA 4020 • • NC FP RP RP1 WM8620A WM8420A • DDA 5005A • • • • • • • • • • • • • RP1 RP1 RP1 Recommended Not Compatible Operates at Full Performance Operates with Reduced Performance with LPA adapters. Frequency response > 3 GHz may be altered Operates with Reduced Performance with LPA adapters.
P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBES ACCESSORIES ORDERING INFORMATION PK001 – Standard Probe Accessory for PP002 Ground Lead PP002 Probe Tip to BNC adapter Sprung Hook PP002 M/F Lead – Long (4") M/F Lead – Short (2") PK102 – Standard Probe Accessory Kit for PP005/PP005 Sprung Hook (Black) Spring Tip (0.38 mm) Spring Tip (0.8 mm) Rigid Tip (0.
P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBES ACCESSORIES ORDERING INFORMATION PKIT1-5MM-102 – Basic Adapter Kit for PP009 Sprung Hook Standard Ground Lead Adjustment Tool Rigid Tip, 0.8 mm IC Cap, 2.54 mm pitch Spring Tip 0.8 mm (Qty. 6) BNC Adapter Adapter, 4 mm plug Ground Spring High Frequency Compensated Ground Lead Spring Tip 0.38 mm (Qty.
www.lecroy.com 251 PROBES AND PROBE ACCESSORIES PK1-5MM-112 Dual Adapter 5.0 to 0.8 mm socket PK1-5MM-111 Adapter 5.0 to 0.8 mm socket PK1-5MM-116 Flexible Adapter 5.0 to 2 mm banana plug PK1-5MM-117 Flexible Adapter 5.0 to 4 mm banana plug 7 10 M- r 5.0 -5Mapte 1 PK B Ad PC PK1-5MM-124 Spring Tip 0.38 mm PK1-5MM-109 Spring Tip 0.8 mm PK1-5MM-104 Rigid Tip 0.
P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBES The PP007 and PP008 embody leading edge technology in passive probe design. A rugged, general-purpose probe, its small size is optimized for maximum waveform fidelity. The small 2.5 mm ground sleeve provides superior visibility, as well as a greater ability to probe dense circuits than traditional 3.5 mm and 5 mm probes. Its sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head.
www.lecroy.com 253 5 ,0 59 ] 1 [ 1 01 700 ap h PK IC C pitc mm wn) 1.0 (bro PK007-018 Dual Lead Adapter PK007-017 Single Lead Adapter PK007-022 Adapter, 2 mm plug PK007-023 Adapter, 4 mm plug PK007-001 Sprung Hook 2 01 700 ap h PK IC C pitc mm ck) 7 a 2 1. (bl 07 7-0 ap 00 g C PK latin u Ins n tio tec Pro p Ca Passive Probe Accessories for PP007 and PP008 Series PK007-019 Pico Hook PK007-021 Micro Clip, Short PK007-020 Micro Clip, Long [0 9] 03 0, 0 01 700 ap h PK IC C pitc mm y) 0.
P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBE ACCESSORIES ORDERING INFORMATION PP007 AND PP008 PROBE ACCESSORIES PK701 Sprung Hook 2 Standard Ground Lead 2 Adjustment Tool 1 Rigid Tip 2 Spring Tip 2 Color Coding Rings (3 Red, 3 Yellow, 3 Blue, 3 Green) Insulating Cap IC-cap for 0.5 mm Pitch IC-cap for 0.65 mm Pitch IC-cap for 0.8 mm Pitch IC-cap for 1.0 mm Pitch IC-cap for 1.
P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES ZS SERIES HIGH IMPEDANCE ACTIVE PROBES The ZS Series probes provide high impedance and an extensive set of probe tips and ground accessories to handle a wide range of probing scenarios. The high 1 MΩ input resistance and low 0.9 pF input capacitance mean this probe is ideal for all frequencies. The ZS Series probes provide full system bandwidth for all LeCroy oscilloscopes having bandwidths of 1 GHz and lower.
P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES A VARIETY OF PROBE TIPS FOR VARIED TASKS Engineers often need to probe a variety of different test points in confined spaces. The extensive range of standard and optional tip accessories for the ZS Series of probes ensures that this probe can meet any difficult probing challenge.
P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES EXTENSIVE SET OF PROBE TIPS AND GROUND LEADS FOR A WIDE RANGE OF PROBING SCENARIOS The Straight Tip and Offset Ground Lead can be used together for probing signal and ground points extremely close together. Hard-to-reach spaces can be be probed with the Bent Sharp Tip and can be used with a range of ground leads like the flexible Short Right-angle Lead shown here.
P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES ORDERING INFORMATION (Set of 4) ZS1500 Active Probes (Set of 4) ZS1000 Active Probes 1.5 GHz, 1 MΩ, 0.9 pF Active Probe 1 GHz, 1 MΩ, 0.
www.lecroy.
P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES HFP2500 HFP ACTIVE PROBES LeCroy’s series of HFP active probes are versatile, small and lightweight, yet still maintain the high bandwidth needed for accurate measurement. Five interchangeable tips facilitate access regardless of tight fits and difficult locations.
P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES ACCESS. INCLUDED WITH STANDARD CONFIGURATION Straight Tip Sharp Tip Bent Tip Discrete SMD Tip IC Lead Tip Square Pin Ground Spring Flexible IC Ground Bendable Pogo Ground Solder-In Ground Short Single Lead Long Single Lead Right-angle Short Single Lead Right-angle Long Single Lead Clips (0.8 mm) FreeHand Probe Holder Replaceable Cartridge Microclips (0.
P R O B E S A N D P R O B E A C C E S S O R I E S HIGH-BANDWIDTH TRANSMISSION LINE The PP066 is a high-bandwidth passive probe designed for use with the WaveMaster and other high-bandwidth oscilloscopes with 50 Ω input termination. This very low capacitance probe provides an excellent solution for higher frequency applications, especially the probing of transmission lines with 20–100 Ω impedance.
P R O B E S A N D P R O B E A C C E S S O R I E S DIFFERENTIAL PROBES High bandwidth, excellent common-mode rejection ratio (CMRR) and low noise make these active differential probes ideal for applications such as disk drive design and failure analysis, as well as wireless and data communication design. With the ProBus interface, the AP034 and AP033 become an integral part of the oscilloscope, allowing sensitivity, offset and common-mode range to be displayed on the scope screen.
P R O B E S A N D P R O B E A C C E S S O R I E S DIFFERENTIAL PROBES SPECIFICATIONS (CONTINUED) Warranty AP034/AP033 ±200 VDC continuous 1.2 m 0 °C to 50 °C ÷10 Plug-on Attenuator ÷20 Plug-on Attenuator (AP034 only) Plug-on AC Coupler Flex Lead Set (1) Input ‘Y’ Lead (1) Mini Clip, 0.8 mm (3) Mini Clip, 0.5 mm (2) Ground Lead (1) Offset Pins, Round (4) Square Pin Header Strip (1) 1 year PK033 – Standard Probe Accessory Kit for AP033/AP034 Dual Lead Single Lead Offset Pin (package of 10) 0.
P R O B E S A N D P R O B E A C C E S S O R I E S HIGH VOLTAGE PASSIVE PROBES The PPE series includes five fixed-attenuation probes covering a range from 2 kV to 20 kV, and one switchable probe providing ÷10/÷100 attenuation for voltage inputs up to 1.2 kV. All fixed-attenuation, standard probes automatically rescale compatible LeCroy oscilloscopes for the appropriate attenuation of the probe. Features: • Safe, accurate high-voltage measurement • 1.
P R O B E S A N D P R O B E A C C E S S O R I E S HIGH VOLTAGE DIFFERENTIAL PROBES The AP031 is a low cost, battery operated active differential probe intended for measuring higher voltages. The differential techniques employed permit measurements to be taken at two points in a circuit without reference to the ground, allowing the oscilloscope to be safely grounded without the use of opto-isolators or isolating transformers.
P R O B E S A N D P R O B E A C C E S S O R I E S HIGH VOLTAGE DIFFERENTIAL PROBES SPECIFICATIONS ELECTRICAL CHARACTERISTICS Bandwidth Interface 20 MHz (ADP300) 100 MHz (ADP305) 1,400 V peak 1,000 V rms CAT III 1% of Reading 50/60 Hz 80 dB (10,000:1) 100 kHz 50 dB (300:1) 60,000 V/µs (ADP300) 300,000 V/µs (ADP305) 50 mV rms ÷100/÷1000 (automatically selected by scope) Between inputs 8 MΩ, 6 pF Each input to ground 4 MΩ, 1 pF 1 V/div to 350 V/div (ADP300) 200 mV/div to 350 V/div (ADP305) ProBus, 1 MΩ* GE
P R O B E S A N D P R O B E A C C E S S O R I E S CURRENT PROBES Accurately measure AC, DC, and impulse currents. MEASURE CURRENTS IN A WIDE RANGE OF APPLICATIONS Measuring AC and DC Currents LeCroy current probes do not require the breaking of a circuit or the insertion of a shunt to make accurate and reliable current measurements. Based on a combination of Hall effect and transformer technology, LeCroy current probes are ideal for making accurate AC, DC, and impulse current measurements.
P R O B E S A N D P R O B E A C C E S S O R I E S CURRENT PROBES CP031 – 30A, 100 MHz The CP031 is LeCroy’s highest bandwidth current probe. Along with the high 100 MHz bandwidth the CP031can probe continuous currents of 30 Arms and peak currents up to 50 A. The CP031 features a small form factor making it easier to probe on a crowded, compact board.
P R O B E S A N D P R O B E A C C E S S O R I E S CURRENT PROBES SPECIFICATIONS CP031*† CP030*† ELECTRICAL CHARACTERISTICS Max. Continuous Input Current Bandwidth Max. Peak Current at Pulse Width Rise Time (typical) Minimum Sensitivity Max. In-Phase Current Low-Frequency Accuracy AC Noise Coupling 30 A 100 MHz 50 A ≤ 10 µs ≤ 3.5 ns 20 mA/div – 1% ≤ 2.5 mA AC, DC, GND 30 A 50 MHz 50 A ≤ 10 µs ≤ 7 ns 20 mA/div – 1% ≤ 2.5 mA AC, DC, GND GENERAL CHARACTERISTICS Cable Length Weight Max.
P R O B E S A N D P R O B E A C C E S S O R I E S CURRENT PROBES AP015 CP150 CP500 30 A 50 MHz 50 A ≤ 10 s ≤ 7 ns 10 mA/div – 1% AC, DC, GND 150 A 10 MHz 500 A ≤ 30 µs < 35 ns 200 mA/div 500 A 1% ≤ 25 mA AC, DC, GND 500 A 2 MHz 700 A < 175 ns 200 mA/div 1150 A 1% 25 mA AC, DC, GND 2m 300 g 5 mm ProBus, 1 MΩ only‡ Indoor 0 ˚C to 40 ˚C 80% 2000 m 300 V CAT I 2m 500 g 20 mm ProBus, 1 MΩ only‡ Indoor 0 ˚C to 40 ˚C 80% 2000 m 600 V CAT II, 300 V CAT III 6m 630 g 20 mm ProBus, 1 MΩ only‡ Indoor 0 ˚C to 4
P R O B E S A N D P R O B E A C C E S S O R I E S PROBE DESKEW AND CALIBRATION The TF-DSQ fixture facilitates calibration of timing measurements in single-ended and differential probes—a unique concern in high-speed measurements. By requiring only one connection of a probe to the fixture and one button press, the TF-DSQ ensures probe calibration results that are valid for the duration that the probe is connected to the circuit.
P R O B E S A N D P R O B E A C C E S S O R I E S EZ PROBE POSITIONER The EZ-Probe Positioner provides stable, accurate X, Y and Z positioning in one fluid motion. Its unique 3-D joystick, with 3:1 motion reduction and single-clutch, fullyarticulating arm, allow simple, precise positioning in anything from card cages to MCMs. Any current handheld probes can be easily attached, facilitating the measurement process and ensuring more precise connectivity.
