users guide B120D line powered speakerphone with Caller ID
B120D TELEPHONE DIAGRAM CALLER ID DISPLAY MESSAGE WAITING INDICATOR REVIEW KEYS DELETE DELETE REVIEW PRGM PROGRAM MEMORY KEYS REDIAL REDIAL FLASH FLASH RELEASE RELEASE MUTE SPEAKER HOLD HEADSET VOLUME UP HANDSET SPEAKER/HEADSET MUTE HOLD VOLUME DOWN FIGURE 1 HEADSET JACK RINGER VOLUME ADJUST RINGER CADENCE ADJUST DATA PORT FIGURE 1A CONGRATULATIONS AND THANK YOU! CONTACTING TELEDEX Congratulations on your purchase of this quality Teledex analog business telephone.
TABLE OF CONTENTS 1) FEATURES........................................................................……........................2 2) UNPACKING THE B120D....................................................................................2 3) IMPORTANT CALLER ID INFORMATION............................................................3 4) IMPORTANT NOTICE BEFORE INSTALLATION...................................................3 5) INSTALLATION......................................................…..........
1. FEATURES The Teledex B120D is a line-powered display speakerphone with ten one-touch programmable feature buttons.
3. IMPORTANT CALLER ID INFORMATION To use the phone’s Caller ID and call waiting features, you must be in an area where the services are available, and you must subscribe to the services. Where Caller ID is offered, one or more of the following options are generally available: a) b) c) Caller’s number only Caller’s name only Caller’s name and number 4. IMPORTANT NOTICE BEFORE INSTALLATION Each device that you connect to the phone line draws power from the phone line.
5. INSTALLATION 5.1 DESKTOP INSTALLATION 1) 2) 3) 4) Plug one end of the handset coiled cord into the handset. Plug the other end of the cord into the handset jack located on the left side of the phone base. Place the handset in the handset cradle. Plug one end of the supplied line cord into the LINE jack on the bottom of your phone. Then route the line cord through the left slot of the desk/wall mount bracket. Plug the other end of the modular cord into the wall jack. HANDSET JACK FIGURE 3 5.
5.3 WALL MOUNTING CLIP 1) 2) Located on the front of the telephone, above the speaker grill, is the wall mounting clip. Remove this clip by firmly pushing it upward, in the direction of the hook switch. Rotate the clip 180º so that the side with the protruding edge is towards the top. This edge will hold the handset (please refer to figure 5.) WALL MOUNTING CLIP FIGURE 5 6. USING THE DATA PORT The data port is located on the right hand side of the telephone, as it is facing you.
7.1 RING CADENCES Your phone has three ring cadences, or patterns. To change the cadence, slide the switch located along the right hand side of the telephone to one of the musical notes icons located beneath the switch (please refer to Figure 7.) 8. OPERATION 8.1 PLACING AND ANSWERING CALLS USING THE HANDSET To make a call, pick up the handset. When you hear the dial tone, dial the desired number. To answer an incoming call, pick up the handset or press the SPEAKER key.
To resume the call, press the HOLD key or SPEAKER key. This will remove the call from hold and make the call active. 8.10 USING MUTE To temporarily switch off the microphone of either the speakerphone or handset, press MUTE. The MUTE indicator lights and the microphone turns off, but you can still hear person on the other end of your conversation. Press MUTE again to resume your conversation. 8.
9.2 CALLER ID MESSAGES The chart below explains some commom messages that may appear in the display: # TOTAL # NEW Appears as new calls are received. (#) indicates the number of total calls and new calls. PRIVATE CALLER The caller is blocking the name and/or phone number from being sent. PRIVATE NAME The caller is blocking just the name from being sent. PRIVATE CALL The caller is blocking just the number from being sent. UNKNOWN CALLER The caller is not within a Caller ID service area.
2) Use and store the phone only in normal temperature environments. Extreme temperatures can shorten the life of electronic devices and distort or melt plastic parts. 3) Keep the phone away from dust and dirt, which can cause premature wear of parts. 4) Handle the phone gently and carefully. Dropping it can damage internal circuit boards or external parts, and can cause the phone to work improperly. Modifying or tampering with the phone’s internal components can cause a malfunction.
alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, Telephone lines, and internal metallic water pipe systems, if present, are connected together. This precaution may be particularly important in rural areas.
