User's Manual

ManualsBrandsTeledesign Systems ManualsElectronicsRadio Modem

Table Of Contents

Copyright
Disclaimer
Emissions
- FCC
- Notice
- Safety Warning
- RF Exposure
Table of Contents
TS4000 Overview
- Introduction
- Features
- Connections
- Mounting
- Configuring the TS4000
- AirTest - Data Testing
- Upgrading the TS4000 Firmware
- AirScan
- Remote Diagnostics
- AirCalc - Range Estimation
- Status Lights
Configuration Program
- Using Help
- System Requirements
- Installation
- TS4000 to PC Connection
  - Software Connection
- Programming and Retrieving Configurations
- Storing Configurations
- Diagnostics
Serial Port
- RS-232 Serial Port Basics
- Serial Port Connector
- Signal Levels
- Signal Options
- Configuration Options – Serial Port 1
- Serial Port 2
Radio Setup
- Configuration Options
- Frequency Programming
  - Methods of Programming Channels
  - Frequency Configuration Screen
    - Radio vs. File Settings
- Channel Switching
  - Channel Change with a Control String
- Compatibility
AirNet Packet Protocol
- Overview
- Configuration Options
  - Packet General
  - Packet for Port 1 / Packet for Port 2
- Control and Status Strings
  - Control Strings
  - Status Strings
- Master-Slave System Setup
  - Setting Packet Timeout
    - Example
  - Data Packet Transmit Time
    - Example
- Polled System with Store and Forward Repeaters
- CSMA System Setup
GPS Configuration
- Configuration Options
Testing
- AirTest
  - Data Test
  - BER Test
- AirScan
  - AirScan Controls
Remote Diagnostics
- Remote Diagnostics with Repeaters
- Remote Diagnostics Screen
- Remote Diagnostic Controls
Upgrading Firmware
- Upgrading
Licensing
- User’s License
  - USA (FCC)
    - Licensing Service Companies
    - Other Contacts
  - International
- Manufacturer’s Certification
Service and Support
- Contacting Teledesign
- Returning Equipment
Warranty
- Two Year Warranty
- Exclusions
- Limitations
Appendix A - Serial Ports
- Standard Case
  - Serial Port 1 Pinout
  - Serial Port 2 Pinout
- Watertight Case
  - Pinout
    - Notes
- Standard RS-232 Serial Port Pinout
- Standard Usage of the RS-232 Control Signals
- Signal Levels
Appendix B – ASCII Character Set
Appendix C – Control and Status Strings
- General Strings
Appendix D – Internal Jumper Block
- Factory Default Jumper Settings
- Instructions for Accessing the Jumpers
- Jumper Settings for Power on Serial Port 1 - Pin 9
- Jumper Settings for Power on Serial Port 1 - Pin 4
- Jumper Settings for Power on Serial Port 2 - Pin 9
- Jumper Settings for TTL Levels on Serial Port 1

TS4000 Radio Modem User’s Manual AirNet Packet Protocol 47

A dual repeater system has two repeaters. For the specific configurations

defined in this example, the two repeaters must be able to hear each other.

Polling Host

Base

Remote

Repeater B

Remote

Repeater A

Remote

Configuration Parameter Setting

All Units

Enable Packet Operation Checked

Medium Access Control (MAC) CSMA

Store and Forward Repeater Operation: Repeater Filtering Address

Default Transfer Network Broadcast

CSMA MAC Setup: Data Packets: Tx Index 1

CSMA MAC Setup: Relay Packets: Tx Index 1

Modem Address: Group 1

Base Site

Modem Address: Individual 1

CSMA MAC Setup: Data Pkts: Min Idle Slots 3

Repeater A Site

Modem Address: Individual 2

CSMA MAC Setup: Data Pkts: Min Idle Slots 2

CSMA MAC Setup: Relay Pkts: Min Idle Slots 0

Store and Forward Repeater Operation: All Packets Relay All

Repeater B Site

Modem Address: Individual 3

CSMA MAC Setup: Data Pkts: Min Idle Slots 2

CSMA MAC Setup: Relay Pkts: Min Idle Slots 1

Store and Forward Repeater Operation: All Packets Relay All

Dual Repeater System