Datasheet

ManualsBrandsTELE ManualsMonitoring & Safety Relays2100400

MONITORING RELAY / 1-PHASE CURRENT

V2IM10AL10

Art.Nr.: 2100400

V2IM10AL10P

Art.Nr.: 2100410

Page 1 of 7

TECHNICAL DATA

SUPPLY CIRCUIT

Terminals Li-N

Supply voltage

110 … 240 V

24 ... 240 V

Supply voltage tolerance

-15 / +15 %

-30 / +30 %

Rated frequency 16,6 ... 400 Hz or DC

Rated frequency tolerance 16,0 … 420 Hz

Rated consumption

230 V AC

0,37 W / 1,3 VA

24 V DC

0,25 W / 0,25 VA

Duty-cycle 100 %

Backup power time < 140 ms

Recovery time > 200 ms

Drop-out voltage ≥ 6 V

MEASURING CIRCUIT

Terminals Li-Lk

Measurand current 1-phase

Measuring method True RMS

Monitoring function underurrent (U), overcurrent (O), window (W)

Measuring range 10 A AC/DC

AC/DC current monitoring

Multifunction

Supply voltage 24-240V DC or

110-240V AC

1 change-over contact

Width 22,5 mm

Control element

Tripping delay

Maximum threshold

Minimum threshold

Function selector

Status indication

LED U: Supply voltage

LED Max: Overcurrent

LED Min: Undercurrent

LED R: Relay status

http://tele-online.com

VEO

Summary of content (7 pages)

PAGE 1
V2IM10AL10 VEO Art.Nr.: 2100400 V2IM10AL10P Art.Nr.
PAGE 2
V2IM10AL10 VEO Art.Nr.: 2100400 V2IM10AL10P Art.Nr.: 2100410 MONITORING RELAY / 1-PHASE CURRENT MEASURING CIRCUIT Frequency 16 ... 400 Hz or DC Input resistance 2 mΩ Overload capacity Thresholds permanent load 15 A pulse load < 1 s 50 A pulse load < 100 ms 150 A Max 10 … 100 % Min 5 … 95 % Hysteresis 1% TIMING CIRCUIT Start-up delay fixed approx.
PAGE 3
V2IM10AL10 VEO Art.Nr.: 2100400 V2IM10AL10P Art.Nr.
PAGE 4
V2IM10AL10 VEO Art.Nr.: 2100400 V2IM10AL10P Art.Nr.: 2100410 MONITORING RELAY / 1-PHASE CURRENT GENERAL DATA Tightening torque Electrical connection Wire size max. 1Nm V2IM...
PAGE 5
VEO MONITORING RELAY / 1-PHASE CURRENT V2IM10AL10 Art.Nr.: 2100400 V2IM10AL10P Art.Nr.: 2100410 FUNCTIONS Overcurrent monitoring (O) When the supply voltage U is applied, the output relay R switches into on-position if the measured current is below the adjusted threshold IMax . When the measured current exceeds the adjusted threshold IMax , the set interval of the tripping delay (DELAY) begins. After the interval has expired, the output relay R switches into off-position.
PAGE 6
V2IM10AL10 VEO Art.Nr.: 2100400 V2IM10AL10P MONITORING RELAY / 1-PHASE CURRENT Art.Nr.: 2100410 CONNECTIONS L N I ≤ 10A AC/DC Lk Li N 16 18 15 16 18 15 http://tele-online.
PAGE 7
V2IM10AL10 VEO Art.Nr.: 2100400 V2IM10AL10P Art.Nr.: 2100410 MONITORING RELAY / 1-PHASE CURRENT 67 mm DIMENSIONS 76 mm 22,5 mm CONTACT TELE Haase Steuergeräte Ges.m.b.H. Vorarlberger Allee 38 1230 Vienna Austria http://tele-online.com Page 7 of 7 CALL US +43 / 1 / 614 74 - 0 ONLINE SUPPORT info@tele-online.