User Manual

Index
A
ACQuire?, 2-31
ACQuire:MOD
e, 2-32
ACQuire:NUMACq?, 2-33
ACQuire:NUMAVg, 2-33
ACQuire:STATE, 2-34
ACQuire:STOPAfter, 2-34
Acquisition commands, 2-11
ALLEv?, 2
-35
Arguments, 2-7
ASCII, 2-1
code chart, A-1
AUTORange, 2-36
AUTORange:SETTings, 2-37
AUTORa
nge:STATE, 2-36
AUTOSet, 2-37
AUTOSet:ENABLE, 2-38
AUTOSet:SIGNAL?, 2-38
AUTOSet:VIEW, 2-39
B
BNF (Backus Naur form), 2-1
BUS
Y?, 2-40
C
*CAL?, 2-40
CALibrate:ABOrt, 2-41
CALibrate:CONTINUE, 2-41
CALibrate:FAC tory, 2-42
CALibrate:INTERNAL, 2-42
CALibrate:STATUS?, 2-43
Calibration and Diagnostic commands, 2-11
CH<x>:BANdwidth, 2-44
CH<x>:COUPling, 2-44
CH<x>:CURRENTPRObe, 2-45
CH<x>:POSition, 2-47
CH<x>?, 2-43
CH<x>:INVert, 2-46
CH<x>:PRObe, 2-47
CH<x>:SCAle, 2-48
CH<x>:VOLts, 2-49
CH<x>:YUNit, 2-49
*CLS, 2-50
Command and Query Structure, 2-2
Command Groups, 2-11
Command syntax,
BNF (Backus Naur form), 2-1
Command,
syntax, 2-1
syntax:BNF (Backus Naur form), 2-1
communications modules,
references to, vii
Conventions, vi
Cursor co
mmands, 2-12
CURSor:HBArs:POSITION<x>, 2-52
CURSor:SELect:SOUrce, 2-54
CURSor:VBArs:HDELTa?, 2-55
CURSor:VBArs:HPOS<x>?, 2-55
CURSor:VBArs:POSITION<x>, 2-56
CURSo
r:VBArs:VDELTa?, 2-58
CURSor?, 2-50
CURSor:FUNCtion, 2-51
CURSor:HBArs?, 2-51
CURSor:HBArs:DELTa?, 2-52
CURSor:HBArs:UNIts?, 2-53
CUR
Sor:VBArs?, 2-54
CURSor:VBArs:DELTa?, 2-54
CURSor:VBArs:SLOPE?, 2-57
CURSor:VBArs:UNIts, 2-57
CURVe, 2-58
D
DATa, 2-59
DATa:DESTination, 2-60
DATa:ENCdg, 2-60
DATa:SOUrce, 2-62
DATa:STARt, 2-62
DATa:STOP, 2-63
DATa:TARget, 2-63
DATa:WIDth, 2-64
DATALOGging:DURAtion, 2-64
DATALOGging?, 2-64
DATALOGging:SOURCE, 2-65
DATALOGging:STATE, 2-65
DATE, 2-66
*DDT, 2-66
TDS200, TDS1000/2000, TDS1000B/2000B, TDS2000C, TPS2000 Programmer Index-1