Service Manual CSA 803A Communications Signal Analyzer 070–8780–01 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to the Safety Summary prior to performing service.
"$) *.3425-&.4 -".5'"$452&% #9 &+42/.*8 )"3 " 3&2*", .5-#&2 /. " 0".&, *.3&24 /2 4"( /2 34"-0&% /. 4)& $)"33*3 )& '*234 ,&44&2 *. 4)& 3&2*", .5-#&2 %&3*(."4&3 4)& $/5.429 /' -".5'"$452& )& ,"34 '*6& %*(*43 /' 4)& 3&2*", .5-#&2 "2& "33*(.&% 3&15&.4*",,9 ".% "2& 5.*15& 4/ &"$) *.3425-&.4 )/3& -".5'"$452&% *. 4)& .*4&% 4"4&3 )"6& 3*8 5.*15& %*(*43 )& $/5.429 /' -".5'"$452& *3 *%&.4*'*&% "3 '/,,/73 &+42/.*8 .$ &"6&24/. 2&(/.
WARRANTY ! " " " ! ! " " ! ! "
Table of Contents List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Ć1 Operating Information . . . . . . .
Table of Contents ii Block Diagram Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Ć7 A1 M/F Strobe Drive Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $7$ 8))(56 ''5(66 $7&+ 81&7,21 (&2'(5 17(51$/ /2&.
Table of Contents A15 Memory Management Unit (MMU) Board . . . . . . . . . . . . . . "$7()13/ ,42.$: 05(3)$&( ,/( $4( 10531..
Table of Contents Performance Verification Performance Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Ć1 Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Test Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using These Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents CSA 803A Service Manual Cleaning the Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84&2*/2 .4&2*/2 Visual Inspection . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Interconnecting Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . & ." #0 /' % 0 &%% +&)* ,#+"0 "% &%% +&)* Checks After FRU Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Ć75 0 0 6Ć77 Diagnostic Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Ć79 Diagnostics Overview . . . .
Table of Contents Diagrams Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Ć1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Board Level Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Ć2 9Ć9 Replaceable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Ć1 Parts Ordering Information . . . . . . . . . . . . . . . . . . . . . . . .
viii
List of Figures +)74' > = #/2.+0) '#& 1/2#46/'065 +0 6*' 1//70+%#6+105 +)0#. 0#.;<'4 +)74' > = 19'4> 14& .7) &'06+(+%#6+10 +)74' > = 4+))'4 &)' .'9 #6' (14 +)* 4'37'0%; '.'%6+10 +)74' > = %37+5+6+10 06'4%100'%6 1#4& '56 1+06 1%#6+105 +)74' > = +/' #5' 10641..
+)63' < ; '.07+/) '1-#%+/) 5*' 530$' 6(('3 0#3& +)63' < ; '.07+/) '1-#%+/) 5*' '#& /5'3%0//'%5 08'3 /-: #/& 5*' '#& /5'3%0//'%5 0#3&4 +)63' < ; '.07+/) '1-#%+/) 5*' 30/5 6$1#/'- 44'.$-: +)63' < ; '.
List of Figures " ! " ! " ! CSA 803A Service Manual " " " xi
xii
List of Tables !",%: < ; %!352%-%.4 )-)43 0%#)&)#!4)/.3 $*534-%.43 !.$ 5.#4)/.!, %343 !",%: < ; /7%2< /2$ /.$5#4/2 $%.4)&)#!4)/. !",%: < ; %!352%-%.4 )-)43 0%#)&)#!4)/.3 !.$ 5.#4)/.!, %343 !",%: < ; %34 15)0-%.
xiv
Safety Summary Symbols and Terms Terms in Manuals
Safety Summary Specific Precautions ' &* ( # #+ " $& )( #"' (# "')& -#)& $ &'#" ' (- " (# $& * "( ! (# -#)& #& %) $! "( #"" ( (# ( Power Source ' $&# ) ( ' "( " (# #$ & ( &#! $#+ & '#)& ( ( + "#( $$ !#& ( " (+ " ( ')$$ - #" ) (#&' #& (+ " ( & ')$$ - #" ) (#& " &#)" $&#( ( * &#)" #"" ( #" - + - # ( &#)" " #" ) (#& " ( $#+ & #& ' '' "( #& ' #$ & ( #" Grounding the Product ' $&# ) ( ' &#)" (
Safety Summary CRT Handling # ! &" $ " $ ! # " $ ! " # ! # ! Use the Proper Fuse " % ! $ ! # $ "
xviii
Specifications %&. ." /&+* ,-+1&!". .," &#& /&+*. #+- /"./&*$ *! !'0./&*$ 4+0- "#"- /+ /%" #+- $"*"- ( !". -&,/&+* +# /%" % - /"-&./& "*1&-+*)"*/ ( *! 0."- .," &#& /&+*. +# /%" (" 5 (&./. )" .0-")"*/ *! .," &#& /&+* 1 (0". "#"- /+ /%" ." /&+* #+- "-#+-) * " /"./ ,-+ "!0-". -"#"- /+ /%" ." /&+* #+- !'0./)"*/ ,-+ "!0-".
Specifications TableĂ1Ć1:ăMeasurement Limits, Specifications, Adjustments, and Functional Tests (Cont.
Specifications TableĂ1Ć1:ăMeasurement Limits, Specifications, Adjustments, and Functional Tests (Cont.) Part and Description Measurement Limits (Examine) 2##+ /# !!0- !4 / ). "%1 / ). "%1 / +. "%1 / +. "%1 / +. "%1 Specifications (Check) Adjustments (Adjust) Functional Tests )*)# )*)# 4#. -%$$#-%)$ 3/#-) ' %-#!/ 4#. 5 #).%/%1%/4 ( +8+ / 5 #).%/%1%/4 5 ( ./ '# "%.+' 4 )*)# ( ./ '# "%.+' 4 )*)# ( +8+ / 5 ( ./ '# "%.
1Ć4
Operating Information $ $ # &$ ) "& $ #' ! #$ % % $ # % $$ #) % %# & $ % % % & % $ )* # # & $ % $ !# # ) $ &! % # ! ( #+ $% $ $ $% $ $ % !# $ % % # ! & % ' % ' $ % % % ) $% $ # $ % &$ % # $ % & %) $ % &$ % $%#& % $ !
Operating Information Sampling Head Installation and Removal ! '! %! % $ % % !# $% !# # !' $ " $ $( % %! + CAUTION "&% ! $ &$ % $ " $ # ' #) $&$ "% %! + #! !' # # ' $ $ !# '! % $ #! %#!$% % $ # ' # "" ) '! % !&%$ % # "# % ! % #! % ! % $
Operating Information ! ! " ! # ! ! CAUTION ! # ! ! ! " CSA 803A Service Manual 2Ć3
! ( ( ' % # ##&,) -&+ *& ) # * "*! ( &( . *& . %&$"% # )+''#- )&+( ! #"% +) ") +) &( &*! % &' ( *"&% WARNING GROUNDING. For electric shock protection, make the grounding connection before making any connection to the instrument's input or output terminals. This instrument is safety Class 1 equipment (IEC designation).
Operating Information Power Cord Information %$, ' $' , ) %%'$%' ) %!* $# *' ) $# ( (*%%! , ) #()'*" #) ! . $, '. $' $# * )$' #) ) $# + ( ) $!$'. $ # $ ) $# * )$'( # ) %$, ' $' -$* ' &* ' %$, ' $' $) ' ) # ) $# (*%%! ' ' )$ *' . $, '. $' !* #) .
Operating Information Memory Backup Power ! ! $! ## ! " & # # "#!$ # # # & # ! # # % # !( $ "" # & ! " $! " " ) # & ! " $! " ! % !( $ & ! # ! # # & H ! #) " ## " H "# ! " ## " H "# ! & % ! " H Time & Date ! # !" H " # " "# #" # " ! ! ! # $# # ) ( "# H # $ ! $!" "#!$ # )# $ ! & !) " ) $ "
Operating Information Packaging for Shipment ( "'(&)! "( ' (# ' $$ #& #" '( " ' - #!! & (& "'.
2Ć8
Theory of Operation # &.,*)$2 $- #$"#5, -*'/.$*) *((/)$ .$*)- $") ' ) '345 , *((* .$)" /+ .* !*/, $)+/. # )) '- .#,*/"# .# / '5 # )) ' - (+'$)" # - $.# .# 5 (+'$)" !*/, # )) '- *! -$)"' 5 ) *, .1* # )) '- *! $!! , ).$ ' , 0 $' ' - 1 '' ./, - $) '/ H -1 + , . - , )"$)" !,*( (- $0$-$*) .* +- $0 H /.*- . .* +,*0$ -/$. '3 %/-. $-+' 3 !*, 0$ 1$)" ) !/,.# , ( )/ ' %/-.( ). H 1$) *1- !*, 0$ 1$)" 2+ ) - .$*)- *! .
3Ć2
System Functional Overview !+ + ,!'& + *! + , % "'* -& ,!'& $ $' #+ ' , ! -* 2 Acquisition System Block + '&, !&+ & )-!+!,!'& +1+, % / ! +-(('*,+ ,/' - $2 && $ + %($!& + & '&, !&+ ,/' , )-!+!,!'& & % +-* 2 % &, && $+ !,!'& $$1 ,/' ('/ *2'&$1 +$',+ * (*'.
System Functional Overview Executive Processor Block ".!, .$! /-!, ,!+/!-.- ( )*!, .%)( 1%.$ ",)(. * (!& )(.,)& "), %(-. ( ! .$! 2! /.%0! ,) !--), %,! .- .$! .) *!,"),' .$%- )*!, 4 .%)( ().$!, *,%' ,3 "/( .%)( )" .$! %- .) !2! /.! % #()-.% !&"4 !-.)( .$! %(-.,/'!(. 1$!( *)1!,%(#4)( ), . .$! /-!, - ,!+/!-. ) )(.,)& )*!, .%)(- .$! )(.,)&- ( ')(%.),- .$! ).$!, %, /%. ) , - -$ ,%(# .$! !2! /.%0! -3-.!' /- $,)/#$ .$! !2! /.%0! /- ) , - .$! &-) %( %,! .&3 )(.
System Functional Overview Front Panel Controls 2%1 #/.31/, /& 3(% )2 01)-!1),8 3(1/4'( 3(% &/,,/6).' 3(1%% &1/.3 0!.%, #/.31/,2 H 3(% &1/.3;0!.%, -!*/1;-%.4 "433/.2 H 3(% 3/4#( 0!.%, H 3(% -4,3)&4.#3)/. +./"2 (% -!*/1 -%.4 "433/.2 !1% 3(% 3/0 ,%5%, -%.4 2%,%#3)/.2 &/1 3(% ).2314; -%.3 /4#().' !. )#/. -%.4 )3%- /1 6!5%&/1- 2%,%#32 3(!3 0!13)#4,!1 )#/. -%.4 )3%- /1 6!5%&/1- 1%20%#3)5%,8 (% -4,3)&4.#3)/. +./"2 #/.31/, 3(% &4.#3)/.
System Functional Overview Power Supply !-* 34*6&8*7 +631 *.8-*6 & " 36 " 231.2&0 0.2* :308&,* 7396(* &8 & 0.2* +6*59*2(< '*8;**2 = &2) = !-* " ! ! 7;.8(- &003;7 7*0*(8.32 3+ 0.2* .24987 3+ " 83 " 36 " 83 " 440< 43;*6 83 8-* .278691*28 &7 +3003;7 !962 8-* 6*&6 4&2*0 # 7;.8(- 83 !962 8-* +6328 4&2*0 ! % 7;.8(- 83 71&00 ,6**2 .2).(&836 0&14 7-390) 0.,-8 .2).(&8.2, 8-* 43;*6 .
Block Diagram Descriptions &'1 1#!2'-, "#1!0' #1 2&# "#2 '*#" *-!) "' %0 + 1## '%30# 8 ," 2&# - 0"8*#4#* *-!) "' %0 +1 1## 2&# 1#!2'-, A1 M/F Strobe Drive Board &# 20- # 0'4# - 0" !-,1'121 -$ 2&# $-**-5',% !'0!3'21 H 2 3$$#01 !'0!3'206 H ""0#11 * 2!& !'0!3'206 H 3,!2'-, "#!-"#0 !'0!3'206 H ,2#0, * !*-!) 0 2# %#,#0 2-0 !'0!3'206 H -,20-* 3$$#01 !'0!3'206 ## '%30# 8 $-0 *-!) "' %0 + -$ 2&'1 - 0" Data Buffers &'1 !'0!3'2 3$$#01 2&# '+# 1# -
Block Diagram Descriptions Control Buffer ()2 #)1#4)3 "4&&%12 3(% #.-31.+ 2)'-!+2 2%-3 3. 3(% 31."% 1)5% ".!1$ &1., 3(% ),% !2% .-31.++%1 ".!1$ A3 M/F Power Connect Board (% .6%1 .--%#3.1 ".!1$ #.-2)232 .& "4)+3:)- #.--%#3.12 3(!3 $)231)"43% 3(% /.6%1 24//+7 5.+3!'%2 &1., 3(% %'4+!3.1 ".!1$ 3. 3(% &.++.6)-' ".!1$2 H 31."% 1)5% ".!1$ H ),% !2% .-31.++%1 ".!1$ H #04)2)3).- -3%1#.--%#3 ".!1$ (% .6%1 .--%#3 ".!1$ !+2. 24//+)%2 9 /.6%1 3.
Block Diagram Descriptions A5 Time Base/Controller Board '$ (,$ 2$ .-31.++$1 !. 1# ".-2(232 .% 3'$ %.++.6(-& "(1"4(318 H ("1./1."$22.1 H H 1(&&$1 "(1"4(318 H (,$ 2$ "(1"4(318 H "04(2(3(.- 2823$, (-3$1% "$ H $,.18 , - &$,$-3 4-(3 (-3$1% "$ $$ (&41$ : %.1 3'$ !+."* #( &1 , .% 3'(2 !. 1# Microprocessor '$ ,("1./1."$22.1 ".-31.+2 3'$ 3(,$ ! 2$ -# 31(&&$1 "(1"4(318 (- 1$2/.-2$ 3. ".,, -#2 %1., 3'$ 7$"43(5$ 1."$22.1 /$1%.1,2 +." + .-:+(-$ " +(!1 : 3(.- .
Block Diagram Descriptions .-( -+#!! + &( #, , % - -" -#& , 0#%% ! ' + - #-, (0' -+#!! + ,#!' % - + &, '(+& % -+#!! + &( #, , % - -" 0#%% 0 #(+ -+#!! + ,#!' %, " #!" + *. ' 2 ' ('-+(% , % -, -" ,- - ( -" -+#!! + "2,- + ,#, #' -" #+ - -+#!! + ) -" #!" + *. ' 2 ' + &(/ , -+#!! + "2,- + ,#, ' #&)+(/ , , ',#-#/#-2 0" ' -" -+#!! + ,#!' % ! ,% 0 + - #, ', (+ !+ - + -2)# %%2 & )4) 3 ,#' 0 / #!.+ 4 #!" + *.
Block Diagram Descriptions $)".(& 2*((&2*.( *3 )&,% /'' 4/ #&9/.% 4)& 2*()4-/34 0/*.4 *. 4)& "*. 2&$/2% )& -*.*-5- 6",5& *3 m3 )& $45", /,%/'' "54/ -/%& $",$5,"; 4*/. *3 $45", /,%/'' "54/ -/%& -"8 m3 m3 "*. /3 52"4*/. 7)&2& 52"4*/. "*. *:& %*6*3*/.3 ".5", /,%/'' &84&.%3 4)& 42*((&2 )/,%/'' 4/ ,/.(&2 0&2*/%3 50 4/ 3&; $/.%3 )& $45", /,%/'' 6",5& %&0&.%3 /. 4)& 6",5& /' &15&34&% /,%/'' *. "%%*4*/. 4/ 4)& 4*-& #"3& 3&44*.(3 )& $45", /,%/'' -".
Block Diagram Descriptions Memory Management Unit (MMU) Interface *+5 %+4%7+6 +06'4(#%'5 6*' +/' #5' 10641..'4 61 6*' " #0& 6*' !#8'; (14/ '/14: *+5 +06'4(#%' #..195 6*' " 61 5'0& %1//#0&5 61 6*' /+%41; 241%'5514 6*417)* 6*' +/' #5' 10641..'4 #0& 2418+&'5 6*' 2#6* (14 9#8'(14/ 64#05('45 (41/ 6*' %37+5+6+10 5:56'/ 61 6*' !#8'(14/ '/14: A7 CRT Socket Board *' 1%-'6 $1#4& +5 #0 +06'4(#%' (41/ 6*' $1#4& 61 6*' *' 1%-'6 $1#4& %105+565 1( 6*' (1..
Block Diagram Descriptions A8 CRT Driver Board (% 1)5%1 "/!1$ #/.2)232 /& 3(% &/,,/6).' #)1#4)32 H /1)9/.3!, 26%%0 #)1#4)318 H %13)#!, 26%%0 #)1#4)318 H )'( 5/,3!'% !.$ '1)$ 5/,3!'% '%.%1!3/1 #)1#4)318 H %'!422 #)1#4)3 H H %!- #411%.3 ,)-)3 #)1#4)3 1)$ ")!2 #)1#4)3 (% 1)5%1 "/!1$ #)1#4)318 $1)5%2 3(% 1!23%1 2#!. (% !.$ 2)'.!,2 &1/- 3(% "/!1$ '%.%1!3% 3(% :!7)2 2)'.!, 26%%0 2)'.!,2 !.
Block Diagram Descriptions Degauss &'1 !'0!3'2 0#+-4#1 + %,#2'! $'#*"1 $0-+ 2&# !-*-0 12##* .#0230# %0'**# # + %,#2'! $'#*"1 0# ',"3!#" 2 # !& .-5#09-, 7 + %,#2'! 1-30!#1 &# #% 311 !'0!3'2 .0-"3!#1 , #6.-,#,2' **7 "#! 7',% 1',# 5 4# 5'2& $0#/3#,!7 -$ ..0-6'+ 2#*7 ) 8 &'1 5 4#$-0+ '1 ..*'#" 2- 2&# "#9 % 311 !-'*1 2& 2 0# *-! 2#" -, -2& 1'"#1 -$ 2&# &# "#! 7#" -1!'** 9 2'-, 2&0-3%& 2&# !-'*1 ! 31#1 + %,#2'! $'#*" 2- # ',"3!#" ', 2&# 12##* .
Block Diagram Descriptions * '. ') # 0() ** !* + + & !+ !* + + + + * & !* '%2 ($ + & + !&+ )),(+ $!& !* ** )+ 0 + !*($ 0 '&+)'$$ ) ,)!& + !* +!% + !&+ )),(+ !* +!- & &' & . + !* .)!++ & !&+' + * &*') )'% + +', ( & $ ') ) # 0* - & + ', + ) . ) '&+!&, * +' * & + ) ') + + .!$$ &'+ & !& + * &*') .
Block Diagram Descriptions A12 Rear Panel Assembly )& &"2 ".&, "33&-#,9 ,*.+3 4)& /3$*,,/3$/0& 4/ /4)&2 %&6*$&3 )*3 "33&-#,9 $/.4"*.3 $/..&$4/23 '/2 4)& '/,,/7*.( 0/243 H .& /24 H .& : H .& 2*.4&2 /24 &.42/.*$3 349,& : /24 )& &"2 ".&, "33&-#,9 *3 $/.42/,,&% '2/- 4)& .054 54054 #/"2% 4)2/5() " :7*2& $"#,& )*3 $"#,& $/.4"*.3 4)& '/,,/7*.( 3*(.",3 H *()4:#*4 #*%*2&$4*/.", %"4" #53 H /52:#*4 "%%2&33 #53 H /52 *.4&22504 ,*.&3 H 2&15&34 ".
Block Diagram Descriptions 4, ,1'$/ 0(&+ )0 ,% (+1$/$01 /$ +# '$0$ 0(&+ )0 /$ 20$# !6 1'$ ,+1/,))$/ ,+ 1'$ 5$"21(3$ /,"$00,/ !, /# 1, ",*8 *2+(" 1$ 4(1' 1'$ ",+1/,))$/ '$ " + !$ -/,&/ **$# !6 1'$ *("/,-/,"$00,/ 1, 0$/3("$ $(1'$/ 1'$ +!61$ /$&(01$/ ,/ 1'$ 21!61$ /$&(01$/ Standard RSĆ232ĆC Controller '(0 ",**2+(" 1(,+0 ",+1/,))$/ 0 ",++$"1$# 1, 1'$ 0 *$ # 1 !20 +# ##/$00 !20 0 1'$ ",+1/,))$/ '$ 8 ##/$00 )(+$0 1/ +0%$/ # 1 1, +# %/,* 1'$ *("/,-/,"$00,/
Block Diagram Descriptions A13 Mother Board A14 Input/Output (I/O) Board The A13 Mother board provides the interconnection for the microprocessor signals and the +5 V power among the following boards: H A14 I/O board H A15 Memory Management Unit (MMU) board H A17 Executive Processor board H A18 Memory board The A14 I/O board contains the following circuitry: H Data buffers H Timer configuration circuitry H Real time clock H Serial data interface (SDI) H Temp/tone readback buffer H Tone
Block Diagram Descriptions I/O Delayed Data Buffer !"+ "* -", "+ ,! "&, * ,/ & ,! , -+ & ,! *", $ 1 , -+ Timer Configuration !"+ "* -",*1 "+ '%('+ ' $ , ! & ,!* ,/'3"&(-, , %-$,"($ 0 *+ -"$, /",! "+ * , , + ! & 1, ' , '& ,! , -+ "+ $ , ! +'% ' ,! , ",+ "& ".
Block Diagram Descriptions A15 Memory Management Unit (MMU) Board '$ !- /# "-,0(010 -% 1'$ %-**-4(,& "(/"2(10 H H 3$%-/+ H (0.* 6 (,1$/% "$ H (+$ 0$ -,1/-**$/ (,1$/% "$ H 5$"21(3$ ./-"$00-/ (,1$/% "$ H (0.* 6 H ("/-./-"$00-/ H (1 + . H 3$%-/+ #(0.* 6 "(/"2(1/6 H (#$- '$ !- /# "--/#(, 1$0 "-++2,(" 1(-,0 +-,& 1'$ %-**-4(,& 1'/$$ 02!0601$+0 H (0.
Block Diagram Descriptions Time Base/Controller Interface %7% -6 75%16*)55)( 72 %1( *520 7,) -0) %6) 21752//)5 68&6<67)0 %1( 72 %1( *520 7,) ! 7,528+, 7,-6 -17)5*%') Executive Processor (EXP) Interface ,-6 '-5'8-75< '216-676 2* &-(-5)'7-21%/ &8**)56 %((5)66 0%33-1+ 352+5%0> 0%&/) %55%< /2+-' %1( -17)5*%') 7-0-1+ '21752/ 6 ,-6 '-5'8-75< (-5)'76 (%7% */2: 72 7,) # *520 7,) ! %1( 9-') 9)56% Display IC ,-6 '20321)17 '216-676 2* 7,) *2//2:-1+ *81'7-21%/ '-5'8-76 H '21752//)5
Block Diagram Descriptions Waveform Display RAM ()1 ,%,.07 #)0#3)207 #.-1)121 .& "72%1 (%1% "72%1 #.-2!)- 2(% ,)-),3, ,!6),3, /!)01 .& 4!+3%1 !+.-' 5)2( #.+.0 )-$%6 !-$ .4%00!-'% 3-$%00!-'% )-&.0,!2).- Video DigitalĆtoĆAnalog Converter (DAC) ()1 #)0#3)2 #.-4%021 2(% $)')2!+ $!2! &0., 2(% )1/+!7 )-2. !-!+.' $!2! &.0 2(% .#*%2 ".!0$ A17 Executive Processor Board (% 6%#32)4% 0.#%11.0 ".!0$ #.-1)121 .& 2(% H 6%#32)4% /0.#%11.0 H 3,%0)# #./0.#%11.
Block Diagram Descriptions Numeric Coprocessor ( $%'$ (($' ( 0(% !$ ) # 0%$ #) %'$ (($' ) ) - *) ( #()'* ) $#( # % ' !! ! , ) ) %'$ ' "( # $#)'$!( ) #*" ' $%'$ (($' ( # + ) ' (( ( )$ Bus Controller ( ' * ) $#( ()( $ ) * ' # ' (( * ' # $#)'$! * ' ) ) %'$+ $"" # # $#)'$! ( # !( '$" ) " '$%'$ (($' )$ ) ) ' - *) + *(( ( - *) + *(( ( $#( () $ ) $!!$, # H The syst
Block Diagram Descriptions A18 Memory Board (% %-/18 /!1$ 01/5)$%2 3(% 7%#43)5% 01/#%22/1 6)3( 2823% /.95/,!3),% !.$ &/1 -/23 /0%1!3)/.2 400/13 #)1#4)318 &/1 3(% -%-/1)%2 !.$ $)!'./23)# #)1#4)318 &/1 31/4",%2(//39 ).' !1% ,/#!3%$ /.9"/!1$ ,, !##%22%2 3/ /1 2 !1% ).)3)!3%$ "8 3(% 7%#43)5% 1/#%22/1 "/!1$ 20%#)&)#!,,8 "8 3(% /1 3(% #/.31/,,%1 %&%1 3/ 3(% $)2#422)/. /& 3(% 7%#43)5% 1/#%22/1 "/!1$ %!1,)%1 ). 3()2 2%#3)/.
Block Diagram Descriptions EPROMs, SRAM, and NVRAM *' .'.03: +/%-6&'4 4 :45'. #/& 0/<70-#5+-' *' 4 %0/5#+/ #-- 0( 5*' 01'3#5+/) 4:45'. %0&' #/& &+#)< /045+%4 %0&' (03 5*' ! -- 5*' .'.03+'4 4*#3' 5*' -#5%*'& #&&3'44 $64 *' :45'. 4503'4 .+4%'--#/'064 %0/45#/54 5*#5 5*' 01'3#5+/) 4:45'. %0&' 64'4 #/& 130&6%'4 *' /0/<70-#5+-' %0/5#+/4 4503'& 4'55+/)4 4503'& 53#%'4 #/& 05*'3 /0/<70-#5+-' 1#3#.'5'34 *' .'< .
Block Diagram Descriptions Battery Backup '(1 "(0"3(2 /0.4(#$1 12 -#!7 /.5$0 2. 2'$ -.-84.+ 2(+$ #30(-& 2'$ /.5$0$#8.%% /$0(.#1 .% 2'$ A19 Strobe/TDR Buffer Board '$ 20.!$ !3%%$0 !. 0# (1 ".,/0(1$# .% 2'0$$ , (- "(0"3(21 H 20.!$ 1$-1$ 1$+$"2 "(0"3(207 H 20.!$ #$1*$5 "(0"3(207 H !3%%$0 -# +$4$+ 1'(%2 "(0"3(207 $$ (&30$ 8 %.0 !+."* #( &0 , .% 2'(1 !. 0# Strobe Sense Select '(1 "(0"3(207 ".-1(121 .% 2'0$$ 1(&- + #(.#$1 2'$1$ #(.#$1 0$ -.0, ++7 .
Block Diagram Descriptions A20/A21 Head Interconnect (Power Only) Boards &# # " +1#/!,++#!1 ,4#/ +)6 , /"0 -/,3'"# -,4#/ ,+)6 1, 1&# '+1#/$ !# #14##+ 1&# 0 *-)'+% &# " !,++#!1,/0 +" /' ,+ ! )# !,++#!10 1, 1&# !.
Block Diagram Descriptions A27 & A28 Acquisition System Boards &# !/3'1'2'-, 1712#+ !-,1'121 -$ 25- - 0"1 2&# - 0" ," 2&# !/3'1'2'-, - 0" &# !/3'1'2'-, , *-% !/3'1'2'-, , *-% - 0" !-,1'121 -$ 2&# $-**-5',% + (-0 *-!)1 H 0-%0 ++ *# % ', +.*'$'#01 H !-,4#02#01 H # 130#+#,2 & 0"5 0# H '+',% ," 1 +.*',% &# " !-,20-* &# !/3'1'2'-, , *-% - 0" !-,1'121 -$ 2&# $-**-5',% + (-0 *-!)1 H & 0#" H '+# 1# !-,20-**#0 ',2#0$ !# H '!0-.
Block Diagram Descriptions %"+ 1%" -/, "00,/ /".2"010 % /!4 /" 1&*&+$ *" 02/"*"+1 02 % 0 -/,- $ 1&,+ !") 6 *" 02/"*"+1 1%" ,*- / 1,/ &0 -/,$/ **"! #,/ 1%" --/,-/& 1" *" 02/"*"+1 )"3") +! 1%" 1/ +0&1&,+ ,2+1"/ &0 -/,$/ **"! 1, ), 1" 1%" 0")" 1"! 1/ +0&1&,+ +2* "/ +! 0),-" %" % /!4 /" ,2+10 1%" 01/, " -2)0"0 1% 1 , 2/ #/,* 1%" "$&++&+$ ,# 1%" .
Block Diagram Descriptions Microprocessor %"#%" &&"% "!'%" & ' $( & ' "! &,&' * & ,' & " "% " &'"% ,' & " & % ! ,' & " (!& % %"#%" &&"% % ' & ! ! & ' #%" % ! # %& ! &(% !' % * % %"#%" &&"% &" #'& ! + (' & " ! & %" ' & "!'%" % #%" &&"% ! ! & ' & # ! ' ! ! " "!'%" & ! ( ! & !! ! ' %"!' # ! (''"!& "! ' & # ! ! %
Performance Verification This section contains procedures to check electrical specifications and examine measurement limits listed in Table 4Ć1. Use these procedures to check the CSA 803A following repair, or to verify that the CSA 803A meets specifications. To functionally test the CSA 803A, simply perform the proceĆ dures which have a yes" indication in the Functional Tests column listed in Table 4Ć1. The Specifications or Measurement Limits are given at the beginĆ ning of each procedure.
Performance Verification TableĂ4Ć1:ăMeasurement Limits, Specifications, and Functional Tests (Cont.) Procedure Description Measurement Limits (Examine) Specifications (Check) Functional Tests 0!!) -! .
Performance Verification Test Equipment Table 4Ć2 (Test Equipment), contains suggested test equipment for use in this manual. Procedure steps are based on the test equipment examples given, but you may substitute other equipment with similar specifications. The use of different equipment may alter test results, setup information, and related connectors and adapters.
Performance Verification TableĂ4Ć2:ăTest Equipment (Cont.) Description Minimum Specification Examples of Applicable Test Equipment $!/3%12 &%,!+%93.9,!+% %*31.-)7 !13 4!+ !-!-! ,!+%93.9&%,!+% %*31.-)7 !13 4!+ !-!-! ,!+%93.9 &%,!+% 1%04)1%$ %*31.-)7 !13 &%,!+%93.9 ,!+% %*31.-)7 !13 ,!+%93.9 ,!+% %*31.-)7 !13 .6%1 )5)$%1 W $ +.!$ )2.+!3).- W #.--%#9 3.12 %*31.
Performance Verification TableĂ4Ć2:ăTest Equipment (Cont.
Performance Verification Test Record 4Ć6 Performance Verification
Performance Verification CSA 803A Test Record *./-0)#*/ #-& ( 0) #- #),#- /0-# /# +$ (& - /&+* #-/&$&! /# 0) #- #!%*&!& * Performance Test Minimum Incoming Outgoing Maximum Vertical Accuracy #-/&! ( &* &-.
Performance Verification CSA 803A Test Record (Cont.
Performance Verification CSA 803A Test Record (Cont.
Performance Verification CSA 803A Test Record (Cont.) Performance Test Minimum Incoming !,.$ & ""-!. /, 2 )/,.# )'* ,.'!(. .!* .
Performance Verification Using These Procedures *( +-* 0- . "$) 2$/# . /0+ $''0./- /$*) /# / .#*2. 2# / / ./ ,0$+6 ( )/ $. ) ) #*2 /* *)) / $/ # */# - +-* 0- . - ,0$- *)'4 '$ - / 6 -$ . (+'$)" ! - /* ' 6 ./ ,0$+( )/ *) /# +- $)" + " . !*- ) 3 (+' *! /# / ./ ,0$+( )/ !*- # +-* 0- Conventions in this Manual ) /# . +-* 0- . /# !*''*2$)" *)1 )/$*). - 0. H ' // -. 2$/#$) /# * 4 *! / 3/ $ )/$!4 !-*)/ + ) ' *)/-*'. $) $ /*-.
4Ć12
Performance Tests % % & ! ! & % & "$! '$ % &! & &$ %" & ! % * & %'$ & &% %& - ! ' & ! + & %& & % " + " $ !$ & "$! '$ % ) ( ,+ % & ! & ' & ! %&% ! ' " & ! % !$ %'$ & &% $ ( & & ! "$! '$ '%& & "$! '$ % $ ' & % & ! $ &! & !$ !$ !$ & ! !'& !" $
Performance Tests PowerĆOn Diagnostics ()2 /1.#%$41% 2(.4+$ "% /%1&.1,%$ 6)3()- 3(% !,")%-3 3%,/%1!341% 1!-'% .& _ 3. _ _ 3. _ 6(%- ! /%1&.1,!-#% #(%#* !3 /%!* ./%1!3)-' #.-$)3).-2 )2 1%04)1%$ Setup to Invoke PowerĆOn Diagnostics CSA 803A Sampling Head Procedure to Invoke PowerĆOn Diagnostics CAUTION (% )-/43 $).
Performance Tests ăStep 5:ă %4 4(% 2%!2 0!.%, 4/ !.$ 4(%. 3%4 4(% 3 &2/.4 0!.%, 37)4#( 4/ (%. 4(% )3 &)234 ).34!,,%$ 4(% 2%!2 0!.%, 3(/5,$ "% 3%4 4/ !.$ ,%&4 ). 4(% 0/3)4)/. 2/- 4(%. /. 53% 4(% &2/.4 0!.%, 37)4#( 4/ 0%2&/2- !,, 35"3%15%.4 0/7%2 37)4#().' ăStep 6:ă /.)4/2 4(% &/,,/7).' $)!'./34)# 25. &5.#4)/.3 !.$ ./4% 4(% 2!.'% /& 0/33)",% 2%35,43 Diagnostics !#( 4)-% 4(% &2/.4 0!.
Performance Tests % Extended Diagnostics ! ! Exit # " ! ! % $ ! PowerĆOn Diagnostics Complete # ! # & & # # & 4Ć16 Performance Verification
Performance Tests Sampling Heads %&0 -/, "!2/" 0%,40 1%" 0"12- +! )&010 1%" 1"01 01"-0 #,/ )& / 1&+$ ,, &+ +! ##0"1 2)) ,1" 1% 1 1%&0 &0 + ,-1&,+ ) "+% + "! 2/ 5 -/, "7 !2/" +! &1 #&+" 12+"0 &+1"/+ ) % ++") -/, "00&+$ &/ 2&1/5 &+ ,+'2+ 1&,+ 4&1% +5 ,-"/ 1&,+ ) 0 *-)&+$ %" ! 15-" "&+$ 20"! 1%" )& / 1&,+ %" ! &0 0"/3& " !"3& " +! !,"0 +,1 /".
Performance Tests ăStep 3:ă % #%! ' ##$ " % ' #" & # #)& #"" ' ' #('$(' '# ' & !$ " "$(' '# % ' 2 ' Proceed " ' ##$ " $#$*($ ! "( '#( Store Constants " $#$*($ ! "( '#( ăStep 4:ă ' ($ & #" ('#! ' % ' #" & # #)& & #"" ' ' % ' #" %#! ' & !$ " "$(' Offset " ! #% ! "( '#( Aut
Performance Tests Extended Diagnostics ! 0, ' " '(+," + ) * (*& &(* 0, '+". , +,"' ,! ' ,! % 2 +, " '(+," + ! 1 ' -+ ,( ++"+, ,*(- % +!((,"' ) *," -% *%1 "' + *." '.
Performance Tests ăStep 2:ă Executive ! Block External I/O " Area GPIB
Performance Tests Vertical Reference Voltage )*4 130$&%63& $)&$,4 5)"5 5)& 7&35*$"- 3&'&3&/$& 70-5"(&4 "3& "5 "/% "5 0/ 5)& $26*4*5*0/ /5&3$0//&$5 #0"3% 4&& *(< 63& < )*4 130$&%63& 4)06-% 0/-9 #& 1&3'03.&% *' ."*/5&/"/$& *4 3&26*3&% )*4 130$&%63& *4 /05 /&$&44"39 '03 7&3*'9*/( */4536.&/5 41&$*'*$"< 5*0/4 Specifications )& .&"463&% 70-5"(& .645 #& 8*5)*/ 5)& -*.
Performance Tests ăStep 5:ă ' ' " ' ' % "% + m " ' ! "% % ! " ' % ! & !"' ! ' #& "% % "('& ' &' ' '& ' ! & %) ! " ' & % $( % "% "!' !( ! '" ' "% *"!' % ! " #%" (% Test Points Figure 4Ć1:ăA26 M/F Acquisition Interconnect Board Test Point Locations 4Ć22 Performance Verification
Performance Tests Horizontal Reference Clock %&0 -/, "!2/" 3"/&#&"0 1%" ,//" 1 ,-"/ 1&,+ +! 2/ 5 ,# 1%" 0 %,/&6,+1 ) /"#"/"+ " ), ( 0"" &$2/" 8 %&0 -/, "!2/" 0%,2)! ,+)5 " -"/#,/*"! &# * &+1"+ + " &0 /".2&/"! %&0 -/, "!2/" &0 +,1 +" "00 /5 #,/ 3"/&+$ &+01/2*"+1 0-" &#& 8 1&,+0 Specifications %" ,-"/ 1&,+ ) #/".
Performance Tests ăStep 3:ăSet the Frequency Counter controls/output as follows: Frequency counter Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Frequency A Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +(positive) Attenuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performance Tests Vertical Accuracy ()2 01/#%$41% 2(/62 3(% 2%3402 !.$ ,)232 3(% 23%02 3/ #(%#+ 3(% 5%13)#!, !##41!#7 /& 3(% Setup to Check Vertical Gain CSA 803A Prec. Voltage Source W ! Procedure to Check Vertical Gain ăStep 1:ă .23!,, ! !,)"1!3)/. %!$ ).3/ 3(% 0/2)3)/. 2(/6. ). 3(% 2%340 $)!'1!- 9 9 2,/3 & 3(% 4.)3 )2 ). 3!.$"7 -/$% 2%3 3(% 0/6%1 26)3#( 3/ %3 3(% 1%#)2)/. /,3!'% /41#% 3/ !.$ #/..
Performance Tests ăStep 4:ă %* . * *( ) &##&-) Def Tra &% *&+ %* .
Performance Tests ăStep 11:ă !"!, .* '! 4 ) check ./ ' ,!-/'.- # %)-. .$! . '! -+! %"% .%*)- "*, .$! -!..%)# '!0!'- %) % .! NOTE Specifications are one percent of full scale at each volts/div setting. Example: at 5 mV/div full scale for 10 div is 50 mV, which gives an upper and lower spec tolerance of +0.5 mV and -0.5 mV. TableĂ4Ć3:ăVoltage Source Settings Sens.
Performance Tests ăStep 14:ă #$'+# 0&# $'./0 0. !# / $,)),3/ Def Tra '!,+ 0,1!& "#+0'$5 & ++#) 1 0,1!& #)#!0 Enter Desc 0,1!& ,0# 0& 0 Trace 1 & / ##+ /#)#!0#" 0 0&# /# ,$ 0&# /!.##+ (1/0 ,2# M1 Main ăStep 15:ă #$'+# 0&# /#!,+" 0.
Performance Tests ăStep 3:ă 2*((&2 4)& "3 '0--073 #5440/ 12&33 Source */ ."+02 .&/5 405$) Internal Clock */ 101;51 .
Performance Tests TableĂ4Ć4:ăVertical Offset Test Values Sens.
Performance Tests System Vertical RMS Noise ()1 /0.#%$30% 31%1 2(% ,%!130%,%-2 &3-#2).- 2. ,%!130% 2(% -.)1% .- 2(% 20!#% &0., ! 1!,/+)-' (%!$ #.,/!02,%-2 Setup to Examine Vertical RMS Noise CSA 803A Procedure to Examine Vertical RMS Noise ăStep 1:ă -12!++ 2(% !+)"0!2).- %!$ )-2. 2(% /.1)2).1(.5- )- 2(% 1%23/ $)!'0!, & 2(% 3-)2 5!1 )- 12!-$"6 ,.$% 1%2 2(% 15)2#( 2.
Performance Tests ăStep 5:ă , ,! & "' * & *, "1 + (%%(/+ *, "1 " (' ,(- ! , Vert Size:M1 ,( & ".
Performance Tests Enter Desc $) +*+3/+ ( )/ .*/ # ăStep 10:ă -/, .# 0 '/ - !*''*1- /..*) Measurements $) ( %*, ( )/ RMS $) +*+3/+ ( )/ .# . $- v m Exit Menu .* 2$.
Performance Tests Sweep Rate Accuracy !* ()' ,) * '.* + * +,(* & $!*+* + *+ (* +' # + . ( + ,) / Setup to Examine Sweep Rate Accuracy CSA 803A High Frequency Signal Generator ,+(,+ W W Procedure to Examine Sweep Rate Accuracy ăStep 1:ă &*+ $$ + 1 %($!& !&+' + '%( )+% &+ * '.& !& + * +,( ! ) % *$'+ + ,&!+ . * !& *+ & / %' * + + *.
Performance Tests ăStep 5:ă .'!'% ()'( 02%#)3)/. #!,)"2!4)/. -/$% !3 &/,,/73 "544/. Page to Enhanced Accuracy Time Base Cal Mode ). -!*/2 -%.5 High Prec ). 0/0:50 -%.5 Exit ). 0/0:50 -%.
Performance Tests Sweep Rate Accuracy 1 ns/div ăStep 11:ă 5)& 8&&1 "5& 50 /4 %*7 03*:0/5"- *$0/ 506$) &5 Main Size 50 /4 %*7 "%+645 611&3 ,/0# ăStep 12:ă 5)& *(/"- &/&3"503 50 5)& '0--08*/( 4&55*/(4 3&26&/$9 .
Performance Tests ăStep 22:ă 3'$ Main Pos 3. -2 ăStep 23:ă $3 3'$ Main Pos ".-31.+ +.6$1 *-.! 2. 3' 3 3'$ 9$1. "1.22; (-& .% 3'$ 6 5$%.1, .""412 .- 3'$ "$-3$1 &1 3("4+$ ăStep 24:ă $3 3'$ '.1(9.-3 + 1$%$1$-"$ /.(-3 3. Center 2 %.++.62 2. 3' 3 3'$ 6 5$%.1, 6(++ !$ $7/ -#$# !.43 3'$ '.1(9.-3 + "$-3$1 !433.- /1$22 Horizontal Desc (- , ).1 ,$-4 3.4"' Center (- /.
Performance Tests ăStep 35:ă . .# #*,$4*). ' , ! , ) +*$). .* Center - !*''*1- -* .# . .# 1 0 !*,( 1$'' 2+ ) ,*/) .# #*,$4*). ' ). , /..*) +, -Horizontal Desc $) ( %*, ( )/ .*/ # Center $) +*+5/+ ( )/ .*/ # ăStep 36:ă .# ,.$ ' $4 - !*''*1- ,.
Performance Tests Triggering, External Direct &'0 -/,!#"2/# 3#/'$'#0 1&# !,//#!1 ,-#/ 1',+ +" !!2/ !6 ,$ 1&# 0 1/'%%#/ 0601#* Specifications &# 0-#!'$'! 1',+0 $,/ 1/'%%#/'+% 20'+% 1&# #51#/+ ) 1/'%%#/ /# 0 $,)),40 H * -8- 1 7 H * -8- 1 7 H * -8- 1 7 Setup to Check Triggering CSA 803A # High Frequency Sine Wave Generator 21-21 W " ! Procedure to Check Triggering ăStep 1:ă +01
Performance Tests ăStep 5:ă # , '$$'/!& + $ ,!'&+ -,,'& (* ++ $! ,$0 "-+, , *! * .
Performance Tests Prescaler Triggering *+4 130%'&63' 7'3+(+'4 5*' %033'%5 01'3#5+0/ #/& #%%63#%: 0( 5*' 4 3'4%#-'3 53+))'3 4:45'. Specifications *' 41'%+(+%#5+0/4 (03 3'4%#-'3 53+))'3+/) #3' #4 (0--084 H . 1<1 #5 ; H .
Performance Tests ăStep 3:ă .--$"3 3'$ .43/43 3. 3'$ /.6$1 ,$3$1 2$-2.1 ,$3$1 2$-2.1 ,423 !$ " +(!1 3$# $3 3'$ $-$1 3.1 %1$04$-"7 3. 8 3'$ $-$1 3.1 .43/43 4-3(+ 3'$ /.6$1 ,$3$1 1$ #2 # , , /9/ 2$ ".11$"3(.- % "3.12 %.1 3'$ 2$-2.1 ăStep 4:ă .--$"3 3'$ .43/43 3. 3'$ 1$2" +$1 1(&&$1 (-/43 ăStep 5:ă , (-%1 ,$ 2$33(-&2 DefTra 3.
Performance Tests Internal Clock ()3 02/#%$52% 6%2)&)%3 4(% #/22%#4 /0%2!4)/. !.$ !##52!#8 /& 4(% 3 .4%2.!, ,/#+ 3)'.!, Measurement Limits (% -%!352%-%.4 ,)-)43 /& 4(% ).4%2.!, #,/#+ 05,3% !2% !3 &/,,/73 H 2)3% 4)-% v .3 H &2%15%.#8 /& H $548 #8#,% : + 9 : !##52!#8 Setup to Examine Internal Clock CSA 803A I Procedure to Examine Internal Clock ăStep 1:ă .34!,, 4(% ; !-0,).' %!$ ).4/ 4(% 0/3)4)/. 3(/7. ).
Performance Tests ăStep 5:ă $3 4/ 3'$ 2 %.++.62 !433.- /1$22 Instrument Options (- , ).1 ,$-4 3.4"' Edge Mode (- /./:4/ ,$-4 3.4"' ăStep 6:ă - 3'$ /1$22 3'$ !433.- ăStep 7:ă '$"* 3'$ 1(2$ 3(,$ 2 %.++.62 !433.
Performance Tests Calibrator Output )*2 01/$&%41& 5&1*'*&2 3)& $/11&$3 /0&1"3*/. ".% "$$41"$7 /' 3)& 2 ",*#1"3/1 Measurement Limits )& -&"241&-&.3 ,*-*32 /' 3)& $",*#1"3/1 "1& "2 '/,,/62 H H 1*2& 3*-& v 02 - 9 Setup to Examine Calibrator CSA 803A I Procedure to Examine Calibrator ăStep 1:ă .23",, 3)& : "-0,*.( &"% *.3/ 3)& 0/2*3*/. 2)/6. *. 3)& 2&340 %*"(1"- 2,/3 ' 3)& 4.*3 6"2 *. 23".
Performance Tests ăStep 6:ă ' ,! )* ++ ,! -,,(' ăStep 7:ă ! $ ,! *"+ ,"& ' ) $1,(1) $ &)%",- + (%%(.
Adjustments ( ( ) $# $#) #( %'$ *' ( )$ ! )' ! (% ) $#( )$ -/ " # " (*' " #) ! " )( # )$ " #* !!. ( ) !! #) '# ! *()" #)( ! () # ! / ( ) ( %'$ *' ( )$ ' )*'# ) )$ (% / $% ' ) $# $!!$, # ' % ' $' ( % ') $ $"%' #( + % ' $'" # ) () %'$ *' )$ + ' . ) ) ) " )( (% ) $#( $ *() ) ( "%!.
Adjustments TableĂ5Ć1:ăMeasurement Limits and Adjustments Procedure Description Measurement Limits (Examine) Adjustments (Adjust) /,3"(& 400,7 3/ ./.& /,3"(& &'&1&.$& 3/ &' '/1 &(4,"3/1 &'&1&.$& 3/ &' '/1 /6&1 400,7 *20,"7 43/'' 5*2*#,& /. 31".2'/1-&1 /. 1*5&1 #/"1% 4.3*, %*20,"7 "00&"12 /.5&1(&.$& 01*-"17 $/,/12 "1& ./3 2&0"1"3&% *. 3)& 6)*3& (1*% '/1 /03*-4- $/.5&1(&.
Adjustments Test Equipment Table 5Ć2 (Test Equipment), contains suggested test equipment for use in this section. Procedure steps are based on the test equipment examples given, but you may substitute other equipment with similar specifications. The use of different equipment may alter test results, setup information, and related connectors and adapters. TableĂ5Ć2:ăTest Equipment Description Minimum Specification Examples of Applicable Test Equipment Digital Voltmeter (w/test leads) v0.
Adjustments TableĂ5Ć2:ăTest Equipment (Cont.
Adjustments TableĂ5Ć2:ăTest Equipment (Cont.
Adjustments Using These Procedures *( +-* 0- . "$) 2$/# . /0+ $''0./- /$*) /# / .#*2. 2# / / ./ ,0$+6 ( )/ $. ) ) #*2 /* *)) / $/ # */# - +-* 0- . - ,0$- *)'4 '$ - / 6 -$ . (+'$)" ! - /* ' 6 ./ ,0$+( )/ *) /# +- $)" + " . !*- ) 3 (+' *! /# / ./ ,0$+( )/ !*- # +-* 6 0- Conventions in this Manual ) /# . +-* 0- . /# !*''*2$)" *)1 )/$*). - 0. H ' // -. 2$/#$) /# * 4 *! / 3/ $ )/$!4 !-*)/ + ) ' *)/-*'. $) $ /*-. ) *)) /*-.
Adjustments Power Supply This procedure shows the setup and lists the steps to examine the MeaĆ sured Voltage Supply and to check and adjust the Voltage Reference and the Regulator Reference (see Figures 5Ć1, 5Ć2, and 5Ć3). This procedure should only be performed if the instrument is out of measurement limits and maintenance is required. If the CSA 803A is already within limits, proceed to the Display adjustment procedure.
Adjustments ăStep 4:ă TP200 VCC TP300 GND P106 (To A13 Mother Board Connector) Front of Oscilloscope Lithium Battery (BT150) Figure 5Ć1:ăA18 Memory Board Test Point Locations 5Ć8 Adjustment Procedures
Adjustments Setup to Examine/Adjust Voltage Reference CSA 803A Digital Voltmeter ) .6 #! # ! ! " $! ( ()2 /1.#%$41% 2(.4+$ .-+7 "% /%1&.1,%$ )& ,!)-3%-!-#% )2 1%04)1%$ ()2 )2 -.3 -%#%22!17 &.1 5%1)&7)-' )-2314,%-3 2/%#)&)#!3).-2 Procedure to Examine/Adjust Voltage Reference ăStep 1:ă %1&.1, 3(% &.++.6)-' 2%33)-'2 )- 3(% .1$%1 +)23%$ ! %3 3(% &1.-3 /!-%+ 26)3#( 3. !-$ 3(% 1%!1 /!-%+ 3. )2#.
Adjustments ăStep 3:ă /&# #$ +* /&# +*/-+( #!/'$'#+ -" /+ ăStep 4:ă #)+1# /&# '%'/ ( +(/)#/#- (# ". $-+) /&# /#./ ,+'*/. ăStep 5:ă #/ /&# -# - , *#( /+ ăStep 6:ă '.!+**#!/ /&# $-+) /&# ,+2#- .+0-!# ăStep 7:ă #)+1# (( /#./ (# ". *" /&# .&+-/'*% ./- , ăStep 8:ă #,( !# /&# +2#- 0,,(3 )+"0(# 0.'*% /&# '*./-0!/'+*.
Adjustments Setup to Examine/Adjust Regulator Reference CSA 803A Digital Voltmeter ' -4 " ! " & ! ! ! ! Procedure to Examine/Adjust Regulator Reference ăStep 1:ă )# 1&# !-,,#!1'-,0 0&-4, ', 1&# 0#12. ," '%2/# 5 "' 5 %/ +0 &#!) 1& 1 1&# .-4#/ '0 ăStep 2:ă '1& 1&# '%'1 * -*1+#1#/ ', -*1 %# +-"# 1&# -*15 +#1#/ $-/ /# "',% 4'1&', 1&# *'+'10 -$ ," 11#+.
Adjustments Com Test Point Ref Test Point R730 +10 V Ref Figure 5Ć3:ăA4 Regulator Board Test Point and Adjustment Locations 5Ć12 Adjustment Procedures
Adjustments Display !+ (*' -* + '/+ , + ,-( & $!+,+ , +, (+ ,' 0 %!& & "-+, , ' # , ' * & , *!. * ' * + ! -* + 3 & 3 "-+,% &,+ !& , !+ (*' -* '&$1 , , .!+- $ +( ,+ ' , !+($ 1 & 1'- + '-$ '&$1 ( * '*% , + "-+,% &,+ / & , ' # , ' * '* *!.
Adjustments Setup to Examine/Adjust the Display CSA 803A Procedure to Examine/Adjust the Display WARNING ăStep 1:ă * (*& ," (%%(/#'! + ,,#'!+ #' ," (* * %#+, ăStep 2:ă &(. ," ,() ' (,,(& #' , ) ' % (. *+ ăStep 3:ă &(. ," ,"* + * /+ ," , + -* ," (. * ' ," ' * &(. ," (. * ăStep 4:ă &(.
Adjustments ăStep 13:ă .3"' Run (- 2'$ , ).0 ,$-3 ăStep 14:ă " 2' 2 2'$ /0(, 07 ".+.01 0$# &0$$- -# !+3$ 0$ -.2 1$/ 0 2$# (- 2'$ 5'(2$ &0(# / 22$0- WARNING " ! ! ăStep 15:ă .- 2'$ ."*$2 !. 0# %.0 2'$ ./2(,3, 4$02(" + ".-4$0&$-"$ .% 2'$ 0$# &0$$- -# !+3$ ".+.01 ăStep 16:ă " 2' 2 2'$ &0(# / 22$0- (1 %.
Adjustments ăStep 26:ă /$ / /$! +(+- . (! %. 2$%/! / /$! /+, #- 4 / /$! +//+) * /$! '#-+0* +* /$! -%#$/ .% ! +" /$! %.,( 4 %. 0/ +"" /$ / %. /$! 1!-/% ( - ./!- (%*!. -! *+/ 1%.% (! +* /$! -%#$/ .% ! +" /$! %.,( 4 " /$! #- 4 . (! )!!/. /$! ,-!1%+0. +* %/%+*. + *+/ ,!-"+-) /$! &0./)!*/. %* /!,. * -+ !! /+ /!, ăStep 27:ă * + '!/ + - "0((4 +0*/!- (+ '2%.! +* /$! ăStep 28:ă (+ /! +* /$! /- *.
Adjustments ăStep 40:ă &0 ' +! '$') "*($ 0* +! + "* +! Red Display Green Disply ') Blue Display *!'. * - ) '$') "%(,)"+" * +! & ( ) ')% +! '$$'."& +' ) *+') +! '$') (,)"+0 H &*,) +! + +! &-")'&% &+ "* ) ' $$ /+ )& $ % & +1 " " $ * ') / %($ % & +" * ) . )"- ) & ) +! ',$ ,* '$') "%(,)"+" * '& +! * ) & H + +! *."+ ! +' H "+ * '& * +! & * + +! *.
Adjustments FOCUS SCREEN VERTICAL POS R311 HĆPOS R500 HĆSIZE R501 HĆLIN R502 VERT SIZE L321 Figure 5Ć4:ăA8 CRT Driver Board Adjustment Locations 5Ć18 Adjustment Procedures
Adjustments GREEN R201 RED R200 BLUE R203 CONVERGENCE R210 Figure 5Ć5:ăA7 CRT Socket Board Adjustment Locations CSA 803A Service Manual 5Ć19
Adjustments Real Time Clock * ')& ,) - ) * + &)) + &' ) + &% % ,) / & + * %',+ &,+',+ */*+ $* * ,) 2 * ')& ,) * &,# ' ) &)$ &%#/ $ %+ % % * ) (, ) +* ,* * %&+ % ** )/ &) - ) / % %*+),$ %+ *' + &%* Measurement Limits $ *,) $ %+ # $ + &) + ) # + $ #& " * m* 1 m* Setup to Examine/Adjust Real Time Clock CSA 803A Frequency Counter ! " ! Procedure
Adjustments ăStep 2:ăPerform the following operations in the order given: H Set the front panel ON/STANDBY switch to STANDBY. H Remove the L bracket on the front of the card cage. H Remove both plastic retaining strips from the top of card cage. H Remove the A17 Main Processor board, and then install it in the fourth slot from the outer edge. H Remove the A29 Memory Expansion board, and then install it in the third slot.
Adjustments ăStep 7:ă ' % # "& ) & % # # % ! ( # & ăStep 8:ă % % $( % % ăStep 9:ă ! % # & % # $ # ## % ! % # # * ! $ % $ TP31 Ground C510 Real Time Clock Figure 5Ć6:ăA14 I/O Board Test Point and Adjustment Locations 5Ć22 Adjustment Procedures
Preventive Maintenance ! " " ! ! " # Removing the Cabinet Panel WARNING
Preventive Maintenance Cleaning the Instrument CAUTION
Preventive Maintenance Interior # % # ## ") $ $ " " ' $ %#$ ' $ ") '*& $) " " ( $ ) @ & ) "$ $ $ " # ' $ # $ "%# " $ ' $ $ " $ ' $ " # %$ $$ *$ $ " # %# % " "" ' # # " " " $ " % $ $# $ " %# ' # $ ' $ ' $ " $ " & ) " # % CAUTION
6Ć4
Corrective Maintenance # Power Supply Voltage Hazard " # " # WARNING ! # ! " ! ! ! # ! # "
Corrective Maintenance StaticĆSensitive Device Classification CAUTION !"+ "&+,*-% &, '&, "&+ $ ,*" $ '%('& &,+ ,! , * +-+ (," $ ,' % *'% +, ," "+ ! * $ 1 '* ,! * $ ,". +-+ (," "$",0 ' . *"'-+ $ ++ + ' + %" '& - ,'*+ , ," .'$, + ' # ,' # * '%%'& "& -&(*', , &.
Corrective Maintenance # "& $ ' " %$ # $ & H H " # "$ #$ " #$ $ *# # $ & $# " ## # $ " " $ "# $ *#$ $ $% " " % $ & ( $ $ $ # #$ $ *# # $ & ## # " $# H # " $ #$ $ & $ " ( %" ( ( ' " '" #$ #$" ' $ # $# "& #$ $ *# # $ & ## # " $# # % " " ( $ #$ $ * " ' " #$ $ ( !% #
Corrective Maintenance Removing and Replacing FRUs 0$ !)$ 7 0 ",+3$+($+1 /$%$/$+"$ %,/ %(+#(+& ",++$"1,/ +# 0"/$4 )," 1(,+0 4'$+ /$*,3(+& +# /$-) "(+& %($)# /$-) "$ !)$ 2+(10 0 '$ %(/01 ",)2*+ (+ 1'$ 1 !)$ )(010 1'$ 1, !$ /$*,3$# ,/ /$-) "$# +# 1'$ 0$",+# ",)2*+ )(010 1'$ %(&2/$0 1' 1 6,2 0',2)# /$%$/$+"$ %,/ 1'$ )," 1(,+ ,% ",++$"1,/ +# 0"/$4 )," 1(,+0 #(0"200$# (+ 1'$ -/,"$#2/$ 1, /$*,3$ /$7 -) "$ 1'(0 TableĂ6Ć2:ăFRU Removal/Replacement Figure Cross Reference FRU to be Removed/ Repl
Corrective Maintenance TableĂ6Ć2:ăFRU Removal/Replacement Figure Cross Reference (Cont.) FRU to be Removed/ Replaced Figures to Reference During Removal !#/' .*, * , %#/,! 4 %#/,! 4 %#/,! 4 %#/,! 4 %(! -! *).,*''!, * , %#/,! 4 %#/,! 4 * &!. * , ,%0!, * , !(*0%)# !+' %)# .$! ,%0!, * , /'.%4 %) *))! .*, ,%!). .%*) ) !(% *) / .
Corrective Maintenance TableĂ6Ć2:ăFRU Removal/Replacement Figure Cross Reference (Cont.) FRU to be Removed/ Replaced Figures to Reference During Removal +0&#. + ." '%1.# '%1.# '%1.# '%1.# *,10 10,10 + ." #)+.5 * %#. *'0 + ." '* .+!#//+. + ." Page 6 6 6 6 +, '#3 +$ 0&# ." %# #)+2'*% #,( !'*% 0&# +0&#. + ." #)+2'*% #,( !'*% 0&# + .
Corrective Maintenance TableĂ6Ć2:ăFRU Removal/Replacement Figure Cross Reference (Cont.) FRU to be Removed/ Replaced Figures to Reference During Removal (+%/ *$ ".2(0(1(,+ +1$/",++$"1 , /# (&2/$ 7 (&2/$ 7 (&2/$ 7 (&2/$ 7 (&2/$ 7 (&2/$ 7 (&2/$ 7 ".2(0(1(,+ + ),& , /# (&2/$ 7 (&2/$ 7 (&2/$ 7 (&2/$ 7 ".
$ $ # $ $ " $ !
Corrective Maintenance Electrical LockĆOn of the Front Panel ON/STANDBY Power Switch -+# ..*'! 2'-,1 -$ 2&# + 6 0#/3'0# 2& 2 2&# .-5#0 0#+ ', -, - #*#!20'! **6 *-!) 2&# .-5#0 -, 31# 2&# $-**-5',% .0-!#"30# ăStep 1:ă 5'2!& 2&# 0# 0 . ,#* 2- ăStep 2:ă #+-4# 2&# .-5#0 ! *# ăStep 3:ă -1'2'-, 2&# ',1203+#,2 -, '21 *#$2 & ,"*# 1'"# 1 4'#5#" $0-+ 2&# $0-,2 ăStep 4:ă #+-4# 2&# -22-+ !-4#0 ăStep 5:ă -! 2# 2&# #%3* 2-0 - 0" ăStep 6:ă -! 2# 2&# (3+.
Corrective Maintenance A15 Memory Management Unit (MMU) A8 CRT Driver A14 Input/Ouput (I/O) A18 Memory A12 Rear Panel A7 CRT Socket A17 Main Processor A13 Mother A5 Time Base/Controller CRT Acquisition Unit Holding Rod A11 Front Panel Button A10 Front Panel Control A9 Touch Panel Acquisition Unit Delay Line A2 Power Supply Module A3 M/F Power Connect A4 Regulator Fan Motor Housing A1 M/F Strobe Drive Figure 6Ć1:ăField Replaceable Units (FRU) Locator 6Ć14 Maintenance
Corrective Maintenance A22/A23 Head Interconnect Boards A28 Acquisition MPU Board A21 Acquisition Analog Board A20/A21 Head Interconnect Boards (Power Only) A19 StrobelTDR Buffer Board A26 M/F Acquisition Interconnect Board Figure 6Ć1:ąField Replaceable Unit (FRU) Locator (Cont.
Corrective Maintenance Power Supply Module Removal/ Replacement & ! $ ' $ " " $# # ! ! # ! # ( #! $ " # # ' " ! % # ## ! "" # # & ! # ! ! # $ # ! ! $! ( $! ( ! # ! " ! & # " Power Supply RearĆplate Screws (4) FanĆhousing Screws (4) Line Fuse (F99) Power Supply RearĆplate Screws (4) Rear Panel ConnectorĆplate Screws (4) Rear Panel ConnectorĆplate Screws
Corrective Maintenance J70 J81 J65 Power Supply Module Rear J64 J63 J66 J62 Figure 6Ć3:ăA2A2 Control Rectifier Board Connector Locations # ! $ " & " ! $ ' ăStep 1:ă " ! ! " ! ! ! # $ ! $ " & " $ $ ! ! !! ! ! " ! ăStep 2:ă # ! ! % $ ! ! " ! $ " & " ăStep 3:ă " & " ! $ " & " ! & "! ! ! "
Corrective Maintenance ăStep 4:ă ăStep 5:ă "! " ! ăStep 6:ă ! ! NOTE
Corrective Maintenance Fan Motor Removal/ Replacement %" ) " $ " # " ' $ # & " ! $ $ " # '# ăStep 1:ă # ! " $ ! " $ $ ! $ $ " %# " $ " %# $ " $ ! # $ $ $ " & $ %" # " '# # %" $ %# $ $ " " $ #$"% $ " $ %# # ( % " & $ #$ # " '# ăStep 2:ă ! " $ $ " $ %# " $ $ " ăStep 3:ă & $ $' ' " # $ $ " $ "
Corrective Maintenance Cathode Ray Tube (CRT) Removal/ Replacement WARNING The cathode ray tube (CRT) may retain a dangerous electrical (16 kV) charge. To prevent electric shock, fully discharge the anode before removing the CRT. Short the anode lead from the CRT to the chassis. Wait approximately ten minutes and again firmly short the anode lead to the chassis. Then, remove the CRT. If the CRT breaks, the glass fragments scatter at a high velocity (implosion). Use extreme care when handling the CRT.
Corrective Maintenance ăStep 7:ă % % !& $$ * $ ! '! $%# $$ % # ! % % $ $% ! % %! % !& $$ * %! " % $$ * #! &%% # *!&# (!# $" " % !& $$ * ! %!" ! % $ " ! " #% %$ ! !% % !& $$ * ( " % ! %!" ! % $ " " & + ! " #% %$ ăStep 8:ă # & * $ % % $%#& % ! %$ % $ ăStep 9:ă !' % %(! " $% # & % ! # & $ #! % %!" ! %
Corrective Maintenance ăStep 15:ă ăStep 16:ă ăStep 17:ă CAUTION
Corrective Maintenance CRT Cover CRT Cover Torx Head Screws (3) Figure 6Ć4:ăRemoving/Replacing the CRT Cover CSA 803A Service Manual 6Ć23
Corrective Maintenance A7 CRT Socket Board Cover A7 CRT Socket Board Cover Torx Head Screws (2) Transformer Torx Head Screw (Removed) Transformer Cover A10 Front Panel Control Board A8 CRT Driver Board A9 Touch Panel Assembly Anode Lead Cap CRT Figure 6Ć5:ăRemoving/Replacing the Cathode Ray Tube 6Ć24 Maintenance
Corrective Maintenance Torx Head Screws (4) Top CRT Support Bar Torx Head Screws (4) QuickĆDisconnect Ground Connector Bottom CRT Support Bar Figure 6Ć6:ăRemoving/Replacing the CRT Torx Head Screws CSA 803A Service Manual 6Ć25
Corrective Maintenance Acquisition Unit Removal/ Replacement $"/, - 4 4 ( 4 !), )(( .), - , 1 ( $( 2 &) .$)(- ')0 ( , *& .# +/$-$.$)( /($. - !)&&)1- .# +/$-$.$)( /($. ( , ')0 1$.# .# $(-.,/' (. $( .# (),' & /*,$"#. *)-$.$)( !), && -.
Corrective Maintenance Battery Disposal and First Aid $! %)-.,/(!). *). %)- .$! "*''*1%)# )/( !, *" ..!,%!- *) .$! "*''*1%)# * , - H .1* ..!,%!- %) .$! ) -* &!.- *) .$! %(! -! *).,*''!, * , H *)! ..!,2 *) .$! * , H *)! ..!,2 *) .$! !(*,2 * , !! %#/,!- 3 3 ) ..!,%!- 3 ,!-+! .%0!'2 "*, .$! '* .%*) *" .$!-! WARNING To avoid personal injury, observe proper procedures for the hanĆ dling of lithium batteries.
Corrective Maintenance Emergency and First Aid Information % ) & " %* # &%* * -"*! *! #"*!"+$ ** (" ) ", /&+( $ ( % / ( '(&," ( *! &##&-"% "% &($ *"&% H Manufacturer: % )&%" H Battery Type: "*!"+$ &#/0 ( &% $&%& #&+(" H Solvent # *(&#/* $ +*/(# *&% ") & #&- *&.
Corrective Maintenance FRU Board and Assembly Removal "& '&& ,'*+ * '* $ ,*" $ "&, * '&& ,"'& /",! ! ++"+2%'-&, '%('& &,+ & ',! * ' * + '+, ' * + ++ % $" + "& ,! "&+,*-% &, * %'-&, '& ,! ! ++"+ ! '$$'/"& '-* ' * + ($- '&,' ,! ,'( ' ,! ',! * ' * + " -* 2 '* ,! $' ,"'& ' ,! + ' * + "& ,! * H &(-, -,(-, H %'*1 & % &, &", H 0 -,".
Corrective Maintenance A15 Memory Management Unit (MMU) Plastic Board Guides J53 J57 J52 J83 J90 J78 J72 J77 J77 Rear Panel A18 Memory A14 Input/Output (I/O) A17 Executive Processor (EXP) Rear of Oscilloscope Figure 6Ć7:ăTop View of the Card Cage 6Ć30 Maintenance
Corrective Maintenance A1 M/F Strobe Drive Board $&, # % ( '# $ %* )* ') ( #")* #&- " +( ) 0 % 0 &( &%% *&( ) ( - % "% . #& *"&%) ăStep 1:ă # *! "%)*(+$ %* "% *! "%, (* '&)"*"&% % ( $&, *! &**&$ ' % # ăStep 2:ă $&, &%% *&() % (&$ *! *(& (", & ( ! % ( $&, &%% 0 *&() % (&$ *! *(& (", & ( &* *! '&)"*"&% & *! &%% *&() % "% .
Corrective Maintenance A3 M/F Power Connect Board $&, # % ( '# $ %* )* ') ( #")* #&- " +( ) 0 0 0 % 0 &( &%% *&( ) ( - % "% .
Corrective Maintenance A4 Regulator Board $&, # % ( '# $ %* )* ') ( #!)* #&- ! +( ) 0 0 0 % 0 '(& +( ) &( ( $&, # &( &%% *&( ) ( - % !% . #& *!&%) ăStep 1:ă $&, * &- ( +''#/ $& +# &- ( +''#/ & +# $&, # !% * !) ) *!&% ăStep 2:ă * * !%)*(+$ %* +'(! * ! %&* #( / !% * !) '&)!*!&% ăStep 3:ă $&, &%% *&() % (&$ * +# *&( & ( &* * '&)!*!&% & * $+#*!0'!% &%% *&() !% .
Corrective Maintenance Torx Head Screws (2) J60 J95 J57 J96 Figure 6Ć9:ăRemoving/Replacing the A4 Regulator Board 6Ć34 Maintenance
Corrective Maintenance A5 Time Base/Controller Board &(. % ' * )% & ', +, )+ * %$+, %(/ !(* ('' ,(* + * / ' $' 0 %( ,$('+ $"-* + 2 ' 2 ăStep 1:ă % ,# $'+,*-& ', $' ,# $'. *, )(+$,$(' ăStep 2:ă &(. ('' ,(*+ 0, ' * + $! * + % * $+ )* + ', !*(& ,# $& + (',*(%% * ( * + 0,* & * ,( )* . ', & " ,( ,# % ', * ('' ,(* ,# , / + ,, # ,( * + # ' * &(.
Corrective Maintenance Battery (U511 RAM Socket) Battery (U500 RAM Socket) J91 J16
Corrective Maintenance A7 CRT Socket Board and A8 CRT Driver Board $".+ , 3 3 3 3 3 3 3 3 ( 3 !)+ ) + )(( -)+ , + 0 ( $( 1 &) -$)(, ')/ ( + *& -# ) % - ) + ( -# +$/ + ) + , !)&&)0, ăStep 1:ă ')/ -# -#+ )+1 # , + 0, -# - , .+ -# )/ + ( -# ( + ')/ -# )/ + ăStep 2:ă ')/ -# -0) *& ,-$ $+ .$- ) + ".$ , )( -)* )! -# + " ăStep 3:ă ')/ -# -0) )+1 # , + 0, -# - , .
Corrective Maintenance ăStep 8:ă "$* ( ' # ! $&, ' & +' ( ( ' )& ' ( (& #'. $&" & $# ( & * & $ & ($ ( #'(&)" #( '' ' ' ' & + ' !$ ( ( ( & & $ ( (& #' $&" & & * & $ & ' #$+ #$( (( ($ ( #'(&)" #( '' ' ăStep 9:ă "$* $## ($&' # &$" ( & * & $ & $( ( %$' ( $# $ ( ")!( .
Corrective Maintenance Torx Head Screw J52 J57 J56 J54 J55 Figure 6Ć12:ăRemoving/Replacing the A8 CRT Driver Board CSA 803A Service Manual 6Ć39
Corrective Maintenance A9 Touch Panel Assembly ')0 & ( , *& ' (. -. *- , &$-. &)1 4 !), )(( .), - , 1 ( $( 2 &) .$)(- $"/, - 4 4 ( ')0 ( , *& .# )/ # ( & -- ' &3 - !)&&)1- ăStep 1:ă . .# $(-.,/' (. )( $.- ,$"#. -$ # 1$&& ()1 . .# .)* ăStep 2:ă - 4$( # && ( 1, ( # .) &))- ( .# -' && && ( - , 1$( # )! .# .1) )(.,)& %() - ăStep 3:ă &)1&3 , ')0 .# .1) )(.,)& %() - -) .# . 3)/ ) (). &).# -' && && ( - , 1- $(-$ .# %() - ăStep 4:ă ')0 .
Corrective Maintenance Torx Head Screws (2) A9 Touch Panel Assembly Front of Instrument as Viewed from the Bottom Figure 6Ć13:ăA9 Touch Panel Assembly Torx Head Screws J73 Connector Figure 6Ć14:ăRemoving/Replacing the A9 Touch Panel Assembly CSA 803A Service Manual 6Ć41
Corrective Maintenance A10 Front Panel Control Board $&, # % ( '# $ %* )* ') ( #")* #&- " +( ) 0 0 0 % 0 &( &%% *&( ) ( - % "% . #& *"&%) ăStep 1:ă $&, *! )!" # ( *& *!& / + $&, # "% *!") ) *"&% "%%"% * * ' ăStep 2:ă $&, &%% *&() % (&$ *! (&%* % # +**&% & ( &* *! '&)"*"&% & *! $+#*"0'"% &%% *&() "% .
Corrective Maintenance Torx Head Screws (2) Support Bracket J72 J74 J73 J75 Figure 6Ć15:ăRemoving/Replacing the A10 Front Panel Control Board CSA 803A Service Manual 6Ć43
Corrective Maintenance A11 Front Panel Button Board $&, # % ( '# $ %* )* ') ( #")* #&- " +( ) 0 0 0 0 % 0 &( &%% *&( ) ( - % "% . #& *"&%) ăStep 1:ă $&, *! )!" # ( *& *! ( $&, # "%)*(+ *"&%) +% ( *!& / + $&, # '# $ %* (#" ( "% *!") ) *"&% "%%"% * * ' ăStep 2:ă $&, &%% *&( (&$ *! (&%* % # &%*(&# & ( &* *! '&)"*"&% & &%% *&( ) "% . *(" % # &( &(( * ( '# $ %* ăStep 3:ă $&, *! *-& &(.
Corrective Maintenance A12 Rear Panel Assembly &(. % ' * )% & ', +, )+ * %#+, %(/ #!-* + 2 2 ' 2 (* ('' ,(* + * / ' #' 0 %( ,#('+ ăStep 1:ă &(. ," ('' ,(*+ *(& ," 2 2 ," ' ," ('' ,(* "(% *+ ăStep 2:ă &(. ," #!", (*0 " + * /+ *(& ," (-, * ! + ( ," * * ) ' % ('' ,(* )% , ăStep 3:ă #%, ," )% , $ *(& ," #'+,*-& ', &(. ('' ,(* *(& ," ,() ( ," * ' % ++ & %1 &(.
Corrective Maintenance RSĆ232ĆC Connector J78 Top (As Viewed from the Rear with the Rear Panel Removed) GPIB Connector PRINTER Connector Figure 6Ć17:ăRemoving/Replacing the A12 Rear Panel Assembly 6Ć46 Maintenance
Corrective Maintenance A13 Mother Board !(*0 ' ) ,!+' !(!). -.!+- ,! '%-.! !'*1 !! %#/,!- 4 4 ) 4 "*, *))! .*, - ,!1 ) %) !2 '* .%*)- ăStep 1:ă !(*0! .$! .$,!! *,2 $! - ,!1- .$ . -! /,! .$! *0!, ) .$!) ,!(*0! .$! *0!, !(*0! .$! , #! ,!. %)!, ",*( .$! .*+ ",*). *" .$! , #! 3 ,!(*0%)# .$! , #! - .1* - ,!1- !(*0! *.$ %, /%. * , #/% !- ",*( .$! .*+ *" .$! , #! $! *.$!, !) - *" .$! #/% !- *). %) -'*.- .$ . .. $ .* .$! ! #! *" (!. ' , &!. *.
Corrective Maintenance Torx Head Screws (6) J63A Figure 6Ć18:ăRemoving/Replacing the A13 Mother Board 6Ć48 Maintenance
Corrective Maintenance A14 Input/Output (I/O) Board !! %#/,!- 4 4 4 ) '* .%*)- 4 "*, * , *))! .*, - ,!1 ) %) !2 !(*0! ) ,!+' ! .$! * , - "*''*1- ăStep 1:ă !(*0! .$! .$,!! *,2 $! - ,!1- .$ . -! /,! .$! *0!, ) .$!) ,!(*0! .$! *0!, ăStep 2:ă !(*0! *.$ *" .$! +' -.% * , #/% !- ",*( .$! .*+ *" .$! , #! $!-! #/% !- ,! ,!. %)! 3 .1* -( '' . $!- '* .! %) .1* $*'!- %) .$! '!". , &!. *" .$! , #! $! *.$!, !) - *" .$! #/% !- *). %) -'*.- .$ . .
Corrective Maintenance J78 J77 J90 J72 Front of Oscilloscope Lithium Battery (BT130) P105 (to A13 Mother Board Connector) Figure 6Ć19:ăRemoving/Replacing the A14 I/O Board 6Ć50 Maintenance
Corrective Maintenance A15 Memory Management Unit (MMU) Board #!-* + 2 2 2 ' 2 (* ( * ('' ,(* + * / ' #' 0 %( ,#('+ &(. ' * )% ," ( * + (%%(/+ ăStep 1:ă &(. ," ,"* (*0 " + * /+ ," , + -* ," (. * ' ," ' * &(. ," (. * ăStep 2:ă &(.
Corrective Maintenance J83 J53 J57 J52 Front of Oscilloscope P101 (To A13 Mother Board Connector) Figure 6Ć20:ăRemoving/Replacing the A15 MMU Board 6Ć52 Maintenance
Corrective Maintenance A17 Executive Processor (EXP) Board ! +( ) 0 0 0 % 0 &( & ( &%% *&( ) ( - % !% . #& *!&%) $&, % ( '# * . +*!, (& ))&( & ( ) &##&-) ăStep 1:ă $&, * * ( &(.
Corrective Maintenance J77 Front of Oscilloscope P104 (To A13 Mother Board Connector) Figure 6Ć21:ăRemoving/Replacing the A17 Executive Processor Board 6Ć54 Maintenance
Corrective Maintenance A18 Memory Board " ,) * 1 1 1 1 & 1 ') ' ) '&& +') * ) . & "& / $' +"'&* %'- & ) ($ +! %')0 ' ) * '$$'.* ăStep 1:ă %'- +! +!) ')/ ! * ) .* +! + * ,) +! '- ) & +! & ) %'- +! '- ) ăStep 2:ă %'- '+! ' +! ($ *+" ' ) ," * )'% +! +'( ' +! ) ! ," * ) ) + "& 0 +.' *% $$ + ! * $' + "& +.
Corrective Maintenance Front of Oscilloscope Lithium Battery (BT150) P106 (To A13 Mother Board Connector) Figure 6Ć22:ăRemoving/Replacing the A18 Memory Board 6Ć56 Maintenance
Corrective Maintenance A19 Strobe/TDR Buffer Board "$+ ! # ' %! " #) () %( ' ! () !$, *' ( / / # / $' $## )$' ( ' , # # - !$ ) $#( ăStep 1:ă "$+ ) &* ( ) $# *# ) # %$( ) $# ) &* ( ) $# *# ) # ) *%' ) %$( ) $# ăStep 2:ă "$+ ) ),$ $'- ( ' ,( $# ! ' ) # # ' !$ ) ) ) )$% $ ) &* ( ) $# *# ) )$ ' "$+ ) ( ' ( ăStep 3:ă "$+ $## )$'( # '$" ) )'$
Corrective Maintenance J4C J3C J32 J3A J4A J33A J33B J2B J34 J1B J29A J30A Torx Head Screws (2) Figure 6Ć23:ăRemoving/Replacing the A19 Strobe/TDR Buffer Board 6Ć58 Maintenance
Corrective Maintenance A20/A21 Head Interconnect (Power Only) and A22/A23 Head lnterconnect Boards %,.5!+ !-$ 1%/+!#%,%-3 23%/2 !1% +)23%$ "%+.6 %% )'41%2 9 9 9 9 9 9 !-$ 9 &.1 #.--%#3.1 !-$ 2#1%6 +.#!3).-2 ăStep 1:ă %,.5% 3(% #04)2)3).- 4-)3 !-$ /.2)3).- 3(% #04)2)3).- 4-)3 )3(% 4/1)'(3 /.2)3).- ăStep 2:ă %,.5% 3(% 36. .17 (%!$ 2#1%62 .- %!#( "+!#* 1%3!)-)-' "1!#% +.#!3%$ !3 3(% 3./ .& 3(% #04)2)3).- 4-)3 ăStep 3:ă %,.5% 3(% #04)2)3).- -!+.' ".
Corrective Maintenance J1/2/3/4 Figure 6Ć24:ăRemoving/Replacing the A20/A21 Head Interconnect (Power Only) and the A22/A23 Head Interconnect Boards 6Ć60 Maintenance
Corrective Maintenance Front View of Front Subpanel Assembly Power Only Compartments Sampling Head Compartments Torx Head Screws Torx Head Screws Rear View of Front Subpanel Assembly A22 and A23 Head Interconnect Board Retaining Nuts A20 and A21 Head Interconnect Board Retaining Nuts (Power Only) A22 and A23 Head Interconnect Boards A20 and A21 Head Interconnect Boards (Power Only) Retaining Tabs (4 per Board) Retaining Tabs (4 per Board) Figure 6Ć25:ăRemoving/Replacing the Front Subpanel Assemb
Corrective Maintenance A26 M/F Acquisition lnterconnect Board ')0 & ( , *& ' (. . *- , &$-. &)1 $"/, - 4 4 4 4 4 4 ( 4 !), )(( .), - , 1 ( $( 2 &) .$)(- ăStep 1:ă ')0 .# +/$-$.$)( /($. ( *)-$.$)( .# +/$-$.$)( /($. $( .# /*,$"#. *)-$.$)( ăStep 2:ă ')0 .# +/$-$.$)( ( &)" ) , .# +/$-$.$)( ) , ( .# .,) /!! , ) , ăStep 3:ă ')0 .# !)/, - , 1- )( .# ")& )&), , . $($(" , #)& $(" .# .)* )! .# ,)(.
Corrective Maintenance ăStep 7:ă # ! $ ăStep 8:ă " " ! $ Acquisition Unit Chassis A26 M/F Acquisition Interconnect Board Torx Head Screws (6) Figure 6Ć27:ăTop View of the A26 Mainframe Acquisition Interconnect Board CSA 803A Service Manual 6Ć63
Corrective Maintenance A27 Acquisition Analog Board & " $ #$ # " #$ ' %" # ) ) ) ) " " % # " ' ( $ # ăStep 1:ă & $ !% # $ % $ # $ $ !% # $ % $ $ % " $ # $ ăStep 2:ă & $ $' "( # " '# " $ " $ $ $ $ $ !% # $ % $ $ " & $ # " # ăStep 3:ă & $ "# " $ !% # $ " ) ăStep 4:ă % %
Corrective Maintenance A28 Acquisition MPU Board !( $ " & %& "% $ %& !) '$ % + + + + !$ ! $ ' % $ ) * ! & ! % ăStep 1:ă !( & #' % & ! ' & "!% & ! & '"$ & ăStep 2:ă !( & &)! !$* % $ )% ! $ & $ ! & & & &!" ! & #' % & ! ' & $ !( & % $ % ăStep 3:ă ' '" ! & ) & & % ' & & ! $ % " $ & % $! ! &!$ ! & #' % & ! & $ ! & ! $ ! $ " &
Corrective Maintenance FRU IC Removal " )*( -* + (* * &(.#'! ' * )% #'! ," + #' ," * (-,%#' #' ,"#+ + ,#(' Serial Data Interface Integrated Circuits (SlamĆPack" ICs) #+ &(-', (' ," ( * #!-* 3 (* ," %( ,#(' ( ,"#+ , " + * #+ *# ! " , +#'$ (. * " #+ (*# ', ,( #,+ +( $ , 1 . % (*' * " (," * (*' *+ * '(, " ,( #, ," ! + ( ," +( $ , " .
Corrective Maintenance # & $ & !& $ % " ")% ăStep 1:ă % ! &) , $% # & ( "$! $ " & $ # !& !%& & ! * %#$ ! & "$ ! #"% & "! " & % ! * ) % !"& $ $ CAUTION ăStep 2:ă $$ ! & "& $ "$! $% ) & & &) , $% &" & ( ! + & & % " & %" & ăStep 3:ă & & "( $ & "! & ) & & "( $ % ! & %
Corrective Maintenance Time Base Processor Firmware Serial Data Interlace IC A14-Input/Output (I/O) A5-Time Base/Controller Display Processor Firmware Executive Processor Firmware A15ĆMemory Management Unit A18ĆMemory Acquisition Processor Firmware A28-Acquisition MPU Figure 6Ć30:ăFRU IC Detail 6Ć68 Maintenance
Corrective Maintenance Firmware Integrated Circuits (Dual InĆLine Package" ICs) +( ),4/9$4( 5 $4( .1&$6(' 10 )174 5(2$4$6( %1$4'5 5(( ,*74( < )14 6+( .1&$6,105 10 ($&+ &,4&7,6 %1$4' +( %1$4'5 $0' 6+(,4 4(52(&6,8( ),4/9$4( " $4( H A5 Time Base/Controller board = ,/( $5( 41&(5514 " ! ! ! $0' ! H A15 MMU board = ,52.
Corrective Maintenance H & ! -$! %(,-+.'!(- )( %-, +%#$- ,% ! %" ()- &+! 2 %( -$%, *),%-%)( -) *+)/% ! !,, -) -$! ) + , .*#+ ! %( -$! "%+'0 +! .*#+ ! *+) ! .+! -$ - ")&&)0, ăStep 2:ă !,, ) + , 0%-$%( -$! + #! , ")&&)0, H (,.+! -$ - -$! %, ,!- -) ( -$! *)0!+ )+ %, %, )((! -! H !')/! -$! %(,-+.'!(- , -)* * (!& )/!+ H !')/! -$! -0) *& ,-% ) + #.% !, "+)' -$! -)* )" -$! + #! - -$! &!"- +! + )" -$! %(,-+.
Corrective Maintenance Figure 6Ć31:ăIC InsertionĆExtraction Tool ăStep 4:ă )"* ,# &(*0 ( * !$*&/ * + !(%%(/+ H &(. ,# &(*0 ( * !*(& ,# * " # &(*0 ( * $+ ,0)$ %%0 %( , (' +%(, !*(& ,# (-,+$ % !, +$ (! ,# $'+,*-& ', H ' ,# &(*0 ( * * )% ,# !(%%(/$'" + ' # + ,# % +, ,/(1 $"$,+ (! ,# ) *, '-& * (' ,# * )% 1 & ', +#(-% ,# + & + (* #$"# * ,# ' ,# , (' ,# * &(.
Corrective Maintenance ăStep 6:ăUpgrade the A28 Acquisition MPU board firmware as follows: H Remove the Acquisition unit from the instrument. H Remove the A28 Acquisition MPU board from the Acquisition unit (see Figure 6Ć1 for the exact location of these boards in the AcquisiĆ tion unit). H Locate U611 on the A28 Acquisition MPU board (see Figure 6Ć28). This board is located in the card cage. H Replace U611 on the A28 Acquisition MPU board.
Corrective Maintenance ăStep 8:ă !(*0! .$! +,* ! /,! -!./+ - "*''*1H !. .$! .* H !(*0! .$! ( )/" ./,%)# &/(+!, *) .$! %(! -! *)3 .,*''!, * , H !+' ! .$! *..*( %)-.,/(!). *0!, ) -!. .$! %)-.,/(!). /+3 ,%#$. ăStep 9:ă !,"*,( .$! "%) ' +*1!,3*) ) 0!,%"% .%*) - "*''*1- NOTE H !. .$! ) -1%. $ .
Corrective Maintenance Index MultiĆPin Connectors Cover End Tabs Index Bevel IC Index Retaining Clip Socket Index Spring Mating Recesses SlamĆPack IC Index Index Index Index Index Index Index Dual InĆLine Package IC Note: Figure 6Ć32:ăMultiĆPin Connector Orientation and Semiconductor Indexing Diagram 6Ć74 Maintenance
Corrective Maintenance Cables and Connectors $"& " * % + " -* 2 "+ (*'." ,' +!'/ ,! "&, * '&& ,"& $ + ,/ & ,! . *"'-+ "* -", ' * + %' -$ + & ++ % $" + + ,!"+ " * % + * * & /! & 1'- * * %'.
" " # " ( ! " ' " & " " ! # " " # " !" ( # " " ! $ ! # # ( NOTE Match the index triangles on the multiĆpin connectors with the corresponding square pads on the circuit board. Some multiĆpin connectors are keyed by a gap between the pin 1 and 3 positions in the holder. (A small plastic plug covers the pin 2 position on the end of the holder.
Corrective Maintenance Checks After FRU Replacement $1#/ +6 & 0 ##+ /#-) !#" 1& 1 - /1'!2) / 2+'1 0&,2)" # !&#!(#" )# 7 )'010 1&# /#.
Corrective Maintenance TableĂ6Ć4:ăChecks Required After FRU Replacement (Cont.) 6Ć78 FRU Replaced Checks Required 31."% 4&&%1 .!1$ .6%19 - )!'-.23)#2 73%-$%$ )!'-.23)#2 6%%/ !3% ##41!#8 -3%1-!+ +.#* %!$ -3%1#.-9 -%#3 .6%1 -+8 .!1$2 4-#3).-!+ #(%#* .& ! /.6%19.-+8 $%5)#% 24#( !2 !- 9 9 .1 9 !,/+)-' %!$ %!$ -3%1#.-9 -%#3 .!1$2 .6%19 - )!'-.23)#2 %13)#!+ ##41!#8 823%, %13)#!+ .)2% #04)2)3). -3%1#.--%#3 .!1$ .
Diagnostic Troubleshooting $%. .! /%*) +-*1% !. /$! %)"*-( /%*) )! !.. -4 /* /-*0 '!.$**/ " 0'/4 /* /$! "%!' -!+' ! '! 0)%/ '!1!' ) (*./ .!. %. %- 0%/ * - $! +-%( -4 (! ). "*- /-*0 '!.$**/%)# %. /* 0.! /$! !--*%) !3 * ! *0/+0/ "-*( /$! !-)!' % #)*./% . ) -*..5-!"!-!) ! %/ /* /$! .0.+! / %- 0%/ * - . %) /$! "*''*2%)# / '!. *- /* 0.! /$! 0%'/5%) $!'+ "0) /%*) 1 %' '! %) 3/!) ! % #)*./% . ) %/%*) *)1!)/%*) ' /-*0 '!5 .$**/%)# /! $)%,0!. -! !.
Diagnostic Troubleshooting Kernel Diagnostics '40'. &+#)0156+%5 #4' ':'%76'& '#%* 6+/' 6*' (4106 2#0'. " 59+6%* +5 5'6 61 *' 2'4(14/5 219'4<10 &+#)0156+%5 10 +65 /+%41241%'5514 57$5;56'/5 #0& '.(< '56 &+#)0156+%5 10 #.. 1( +65 /#,14 %+4%7+65 *'0 '40'. &+#)0156+%5 $')+0 6*' /'55#)'5 Diagnostics in Progress #0& Comm Test in Progress #4' &+52.#;'& ( 6*' +5 219'4'&<10 (41/ # %1.& %10&+6+10 6*'0 6*' &+#)0156+%5 /#; %1/2.'6' $'(14' 6*' +5 9#4/'& 72 #0& #$.' 61 &+52.
Diagnostic Troubleshooting %"4 "..+. +!" #+. 0%" -1&/&0&+* ,.+ "//+. #.+) "&0%". &*0".* ( 0"/0 ,+&*0/ +. / "#". 0+ ("/ 6 6 *! 6 #+. )+." &*#+.) 6 0&+* *! "4 ),("/ +# 0%"/" %"4 "..+. +!"/ %" &/,( 5 '".*"( !& $*+/0& / !&/,( 5 * "..+. )"// $" +* 0%" / .""* $&2&*$ 0%" * )" +# 0%" 0"/0 0% 0 # &("! +. "4 ),(" 0%" #+((+3&*$ )"// $" &*!& 0"/ 0% 0 0%" 0"/0 # &("! Dsy Kernel Failure DMA 0 # 0%" "..+. )"// $" !+"/ *+0 ,," . +* 0%" / .""* 0%" "..+.
Diagnostic Troubleshooting % 4 %#,-, -" ,. ,2,- & " + - +, ( -" 1- ' # !'(,-# ++(+ #' 1 ( , TableĂ6Ć5:ăExtended Diagnostics Error Index Code Descriptions Description Meaning 1 .-#/ #,)% 2 #& , & #' + & *.#,#-#(' +('- ) ' % ('-+(%, + -#/ .+#'! -" % 4 ,- # !'(,-# , , *. ' '2 #,-.+ ' & 2 ., - ,- #%.+ (+ #'! -" #'-( -" 1- ' # !'(,-# , &( (. " -" (E)Exit % % -0# #' ,.
Diagnostic Troubleshooting #"! + ' ! ' & !( ' !&'%( !' % '(%!& '" ' & !( ) ' ' & ( &,&' " % "% "(' ! ' ' ' * & ' "% ' # (! ' "! * & !)" "* ) % ' &# , !( , % !' !, & !! ! * & # % "% H (-)Delete .
Diagnostic Troubleshooting Diagnostic Menus ,'' ) '&)+!&% & + !*'# 0 * ) % !* ,* +& !*'# 0 ! %&*+! $ %,* %,* ) &$')!* & $ %, !+ $* % $ %, ! # * %, !+ $* ) )&.* & !+ $* + + % * # + . !# $ %, ! # * ) &#,$%* & *+ +,* !%2 &)$ +!&% ) ) &,) +! )* & $ %,* . ! $ 0 '' ) !% + $ %, ) &%#0 &% !* ') * %+ + %0 !- % +!$ + , *0*+ $ #& " ) % &,+!% $ %,* '&% %+)0 !%+& %0 $ %, + ) !* #.
Diagnostic Troubleshooting H 4 & (% #$- -. ./- $( $ . - .# . .# . -. , +/$, - .$)( !,)' .# /- , -/ # - .# !,)(. * ( & 0 ,$!$ .$)( . -.- ), .# . .# . -. $- !), -.$'/&/- )(&3 -/ # - .# ' (/ & &$ , .$)( . -.- #$- -. ./- ) - (). *,)0$ ! $&/, -. ./- ) 2 /. .#$- . -. - & . $. $( $0$ / &&3 4???? #$- -. ./- $( $ . - .# . ( )*.$)( 1 - !)/( .# . 1 (). *, - (. $( .# /,, (. $(-.,/' (. )(!$"/, .$)( ), .# . -/ -3-. ' 1 - !)/( .# . $ (). # 0 1),%5 $(" )''/($ .$)( * .
Diagnostic Troubleshooting Diagnostic Terminal Mode (RSĆ232ĆC) The RSĆ232ĆC port drives a terminal which conforms to the ANSI 3.64 stanĆ dard. In this mode, the terminal provides a screenĆdriven, interactive human interface. This mode is useful when either the display or touch panel is not functioning properly, or when it is desired to remotely use the diagnostics with a modem and phone link.
Diagnostic Troubleshooting System Mode (GPIB & RSĆ232ĆC) # &!4 -. $ "()-.$ - ( 2. ( $ "()-.$ - , --$ & /-$(" .# .1) )'' ( - &$-. $( & 4 TableĂ6Ć6:ăSystem Mode Commands Header Argument TEST Notes .4)(&3 TEST [XTND] .4)(&3 TEST [MAN] .4)(&3 DIAG? / ,34)(&3 # TEST )'' ( $(0)% - &!4 -. $ "()-.$ - ), 2. ( $ "()-.$ 2 /.$)( # TEST )'' ( 1$.#)/. ,"/' (.- $($.$ . - &!4 -. $ "4 ()-.$ - # TEST )'' ( 1$.# ,"/' (. XTND $($.$ . - 2.
Diagnostic Troubleshooting DIAG? " & !" ! ! ! ! # ' ! ' ! ! %! ! % % ! $ DIAG PASSED: NONE ! ! ! ! ' ! ! %! ' ! ! ! ! ! & ! ! " ! DIAG FAILED: E1311, E1711, E1721, E1731 ! ! ! ! %! ! ! ! ! ! ! " ! DIAG FAILED: E1311, D1211, T1431
Diagnostic Troubleshooting Battery Testing # #)& - !)/, &$.#$/' .. ,$ - .) *,)0$ *)1 , 1# ( .# $(-.,/4 ' (. $- ./,( )!! # !)&&)1$(" $- /--$)(- *,)0$ ,$. ,$ !), . ,'$($(" $! .. ,3 # - 2 $.- &$! .$' ( $- .#/- /-$(" $( ),, . $(-.,/4 ' (. )* , .$)( .. ,3 - &$! .$' 1$&& .3*$ &&3 2 !$0 3 ,- ! .# .. ,3 0)&. " ' -/, - . _ +/ & .) ), ", . , .# ( .# 0)&. " &$-. $( .#$- - .$)( .# ( .# $, /$. -#)/& )* , . ),, .&3 !,)' _ .) _ # - 0)&.
Diagnostic Troubleshooting Clearing NVRAM !"+.! ,+3!.71, !("7 !/0 !#%*/ 8 10 &1/0 "0!. 0$! 4! 10%2! ,.+ !//+. $ / .1* %0/ !.*!( % #*+/0% / 8 0$! ".+*0 , *!( 100+*/ .! / **! 5 0$! 4! 10%2! ,.+ !//+. " 0$! 4! 10%2! ,.+ !//+. /!*/!/ 0$ 0 0$! * 100+*/ * +*(5 0$!/! 03+ 100+*/ .! ,.!//! %* % ! (+/! 1.%*# 0$%/ 0%)! 0$!* 0$! 4! 10%2! ,.+ !//+. .!/!0/ %0/ 0+ !" 1(0 /0 0! 0$! !'/! 1.! . /! !)+.5 "1* 0%+* $%/ !//!*0% ((5 !7 /0.+5/ (( /0+.! /!00%*#/ * /0+.
Diagnostic Troubleshooting FRU Name Abbreviations &&5)9-%7-216 2* " 1%0)6 %5) /-67)( -1 !%&/) = TableĂ6Ć8:ăBoard FRUs FRU Board Board No 752&) 5-9) &2%5( # 2:)5 211)'7 &2%5( )+8/%725 &2%5( ! !-0) %6) 21752//)5 &2%5( ! ! 2'.
Diagnostic Troubleshooting Component and Module Name Abbreviations # ' % $ ! % & $ $ # $% + TableĂ6Ć9:ăComponent Module FRUs FRU Board % * & ) &% ' $! * $ # "& $ % # ( # # % % # % & %% #* ( # &!! * & NOTE The Executive, Display, Time Base, and Acquisition firmware is packaged in a single firmware (FW) kit; the individual parts are not available as separate components.
Diagnostic Troubleshooting Executive Subsystem Error Codes Error index codes for the Executive subsystem are listed in Table 6Ć10 along with the suspected FRUs.
Diagnostic Troubleshooting TableĂ6Ć11:ăExecutive Processor Status LED Configuration GND TP201 (MSB) DS307 DS306 Significance ") $, ! $! %&% * '& ! $! %&% $! %&% ! % TP205 (LSB) +5V DS307 DS306 Figure 6Ć33:ăA17 Executive Processor Board Test Point and Status LED Locations , %&% & * '& ( #$" %%"$ !' & %&% ! ( $ & "! #$" , '$ % & "! & "!% %# ! & ( $ & "! #$" '$ %& $ !"& & & ! & %'
Diagnostic Troubleshooting TableĂ6Ć12:ăExecutive Processor Manual Tests Test Verification Procedure Front Panel % , - % ,& & ' &' "*& ,"( '" !' % ' ) , #% && ' % ,& '" ) % , ' % "# % ' "! & ' &' ) % & ' "# % ' "! " , * ' "' ) &( ! ( " & ' &' % $( % & "# % '"% !' % ' "! ! ! + (' "! , ! ' Routine #"#.
Diagnostic Troubleshooting TableĂ6Ć12:ăExecutive Processor Manual Tests (Cont.) Test Verification Procedure Internal I/O $# # / "% $# ( ) () + ' ( ) % ! ). $ ) #()'*" #) )$ #0 ' ) )$# ( ) '$* )( #) '# ! (% ' ( ) () ' &* ' ( $% ' )$' #) ' ) $# # # - *) $#!. # ) Routine %$%0*% " #* , ) ) Loop "$ ( ) )$ On # ) Terse # All "$ ( ) )$ Off ) ' #+$ # ) ( ) () .$* ( $*! + ' .
Diagnostic Troubleshooting TableĂ6Ć12:ăExecutive Processor Manual Tests (Cont.) Test Verification Procedure GPIB ąInrpt Reset ąReset Status ąData Lines ąInterrupt These tests verify the Executive processor interface to the internal GPIB circuitry. The major external GPIB functions are not tested. This test requires operator interaction and can be executed only in the Routine popĆup menu with the All and Loop modes set to Off.
Diagnostic Troubleshooting DS200 DS201 DIAG 2 (MSB) DIAG 0 (LSB) Figure 6Ć34:ăA15 MMU Board Test Point and Status LED Locations Time Base Processor Error Index Codes ,,*, %) !2 * !- "*, .$! %(! -! +,* !--*, ,! '%-.! %) '! 4 TableĂ6Ć15:ăTime Base Processor Kernel Error Index Codes Error Indexhex Suspect Hybrid/ IC FRUs Suspect Board FRUs $! !,,*, %) !2 * ! %.- *" .$! "%,-. %(! -! &!,)!' .!-. .$ . " %'- ,! ,! ",*( .
Diagnostic Troubleshooting
Diagnostic Troubleshooting Acquisition Processor Error Index Codes ..+. &*!"3 +!"/ #+. 0%" -1&/&0&+* ,.+ "//+. ." (&/0"! &* (" 5 TableĂ6Ć16:ăAcquisition Processor Kernel Error Index Codes Error Indexhex Suspect Hybrid/ IC FRUs Suspect Board FRUs %" "..+. &*!"3 +!" &0/ +# 0%" #&./0 -1&/&0&+* '".*"( 0"/0 0% 0 # &(/ ." ." ! #.+) 0%" -1&/&0&+* + .! /0 01/ / *! "" &$1." 5 #+.
Other Troubleshooting *+4 4'%5+0/ 1307+&'4 #&&+5+0/#- +/(03.#5+0/ #/& 130%'&63'4 (03 5306$-'; 4*005+/) # (#6-5: 50 5*' -'7'- Power Supply Module *+4 130%'&63' 3'26+3'4 #/ 95'/&'& +#)/045+%4 108'3 4611-+'4 5306$-'; 4*005+/) (+9563' '('3 50 #$-' ; (03 # %0.1-'5' &'4%3+15+0/ 0( 5*' '26+1; .'/5 3'26+3'& Module Troubleshooting ( #/: 08'3 611-: .0&6-' 130$-'.
Other Troubleshooting CRT, A7 CRT Socket Board, or A8 CRT Driver Board *+4 130%'&63' 3'26+3'4 # 5'45 5'3.+/#- #/& # %0.1#5+$-' ; ; 4'3+#+/5'3(#%' %#$-' '('3 50 #$-' ; (03 # %0.1-'5' &'4%3+15+0/ 0( 5*' '26+1; .'/5 3'26+3'& Module Troubleshooting ( 5*' 108'34;0/ 5*' " -+)*5 +4 0/ $65 5*' &+41-#: )+7'4 4%3#.$-'& +/(03.#5+0/ 03 /0/' #5 #-- 5*'/ 5*' #/& 3+7'3 $0#3& #3' 4641'%5 *' (0--08+/) 580 130%'&63'4 *'-1 :06 &'5'3.
Other Troubleshooting Fuse Testing The A14 I/O board has four fuses (see Figure 6Ć37). F200 supplies +5 V to the A12 Rear Panel board. F800 supplies +5 V to the A10 Front Panel ConĆ trol board and the A9 Touch Panel board. F600 supplies +15 V to the A14 I/O board, card cage, A10 Front Panel Control board, A9 Touch Panel board, A11 Front Panel Button board, and A12 Rear Panel board (reduced to +12 V).
Other Troubleshooting '' +)52'3 < #/& < (02 4*' -0%#4+0/ 0( 4*' -+/' (53' #/& 4*' $0#2& (53'3 2'31'%4+6'-9 "*'/ # (53' .534 $' 2'1-#%'& 5/30-&'2 4*' (53' (20. 4*' $0#2& ' %#2'(5/04 40 &#.#)' 4*' 30-&'2 1#&3 0/ 4*' $0#2& 4 .#9 $' *'-1(5- 40 342#+)*4'/ 4*' (53' -'#&3 0/ 4*' 2'#2 0( 4*' $0#2& $'(02' 2'.06+/) 4*' -'#&3 (20. 4*'+2 *0-'3 +/ 4*' %+2%5+4 $0#2& '('2 40 4*' Parts List 3'%4+0/ (02 4*' %022'%4 6#-5' #/& 1#24 /5.
Other Troubleshooting Fuse (F200) Fuse (F600) Fuse (F602) Fuse (F800) Figure 6Ć37:ăA14 I/O Board Fuse Locator Diagram CSA 803A Service Manual 6Ć105
Other Troubleshooting Time Base Calibration Errors )# 6 )'/0/ 0&# 0'*# /# ! )' . 0',+ #..,./ 0& 0 ! + --# . ,+ 0&# /!.##+ +" 0&# /1/-#!0#" $ 1)04 / 0& 0 ! 1/# 0&# #..,. &# / .# )'/0#" '+ 0&# ,."#. ,$ *,/0 0, )# /0 )'(#)4 /,1.!# ,$ 0&# #..,. '*# /# ! )' . 0',+ #..,./ 3&,/# #..,. !,"#/ .# %.# 0#. 0& + & 2# 03, "'$$#.#+0 $,.*/ "#-#+"'+% ,+ 3&#+ 0&# #..,. ,!!1./ $ 0&# #..,. ,!!1./ "1.'+% -,3#.6,+ 0&#+ 0&# *#// %# 3')) / 4 Time base calibration failed at power up: 2XX 3&#.
Other Troubleshooting TableĂ6Ć18:ăTime Base Calibration Errors Error Message Error Code Suspect FRU "%&( *"$ ) #" ( *"&% '(& # $ "$ ) #" ( *"&% "# * '&+ (,&% &( $'#"%!
Other Troubleshooting Acquisition Calibration Errors % (,!*!+!&% #! ) +!&% ))&)* & ,) $ ** -!## '' ) &% + * ) % &##&- / %,$ ) + + !% ! + * !% - ! (,!*!+!&% */*+ $ + ))&) - * + + &##&-!% + !* %,$ ) + ) -!## *+)!% & ! + &,)1 ! !+ ))&) & * + + ) ,* +& ! %+! / '&**! # ,#+/ * &##&-!% .
Options ()2 2%#3).- #.-3!)-2 )-&.1,!3).- .- )-2314,%-3 !-$ /.6%1 #.1$ ./3).-2 !5!)+!"+% &.1 8.41 Instrument Options .41 )-2314,%-3 ,!8 "% %04)//%$ 6)3( .-% .1 ,.1% ./3).-2 "1)%& $%2#1)/: 3).- .& %!#( !5!)+!"+% ./3).- )2 ')5%- )- 3(% &.++.6)-' $)2#422).- /3).)-&.1,!3).- )2 )-#.1/.1!3%$ )-3. 3(% !//1./1)!3% 2%#3).-2 .& 3(% ,!-4!+ 2%3 %&%1 3. 3(% !"+% .& .-3%-32 &.1 3(% +.#!3).- .& ./3).- )-&.1,!3).- .1 &413(%1 )-&.1,!3).- !-$ /1)#%2 .& )-2314,%-3 ./3).-2 2%% 8.
Options Power Cord Information %$, ' $' , ) %%'$%' ) %!* $# *' ) $# ( (*%%! , ) #()'*" #) ! . $, '. $' $# * )$' #) ) $# + ( ) $!$'. $ # $ ) $# * )$'( # ) %$, ' $' -$* ' &* ' %$, ' $' $) ' ) # ) $# (*%%! ' ' )$ *' . $, '. $' !* #) .
Electrical Parts CSA 803A Service Manual 8Ć1
8Ć2
Block Diagrams CSA 803A Service Manual 9Ć1
Block Diagrams Board Level Block Diagrams .
Block Diagrams #* % #"'%# ) % " % # ' ! +% ( ' #* % # ( '#% #* % # ' ( ' ' ' % " " $ % ' #" !$ % #* % ( '#% ( '#% ( '#% ( '#% ( '#% ( '#% ' ( ' #* % ( ' #* % "& Figure 9Ć4:ăA4 Regulator Board Block Diagram 9Ć10 Diagrams
Block Diagrams ) % * ## +&) # 0 *+* %&*+ * " +)& %* )&$ +)& *+) ,+ &% ) * # ) ) ) %',+ ) ) & % / ) +)& ) - +& +)& *+) ,+ &% ) ) $ * ) * # ) ) - +& +)& *+) ,+ &% ) + ) ) %',+ & )&$ & )&$ (, * + &% .*+ $* )&, +)& *+) ,+ &% (, * + &% .
Block Diagrams 3 %/-.(!). 3 %/-.(!). 3 %/-.(!). *,$2*). ' 0!!+ $, /$. *$'- ,$ $ - ! ,*( ,!!) '/! %/-.(!). %/-.(!). %/-.(!). * &!. * , !! $"/,! 3 ! ,!!) '/! & -.!, ) ! .!, ! ( /,,!). $($. $"# ) ,$ *'. "! !)!, .*, 1) #,*)$2 .$*) *$'- !,.$ ' 0!!+ $, /$. !" /- %/-.(!). %/-.(!).
Block Diagrams ( ) % '&+)'%% ) '&+)'% '&+)'% #"& % %$ * + '&+)'% ,!! ) * + &- )+ ) + & ) / / &+ )! # %' $ & ) +') )#&+ ) % + / / ) &* #- ) ,!! ) * + &+ )! / / ) &* #- ) ,!! ) + & ) / / '&+)'%% ) + & ) '&+)'% ,!! ) '.
Block Diagrams #*- ,+# # " !( 1$$#. 0 1$$#. 0 1/ 0 1$$#. "".#// 0!& 3#!10'2# 0 1/ ,+# #+#. 0,. "".#// 1$$#. #) 4#" 0 1$$#. "".#// #!,"# #)#!0 0!& 0, # . +#) ,+0.,) 1$$#. '*#. ,+0.,) ' %+,/0'! ),!(/ '*#. ,+$'%1. 0',+ ,%'! # ) '*# ),!( 0 1$$#. "".#// 1$$#. ),!( #+#. 0,. 0, .,+0 +#) ,+0.,) ,+0.,) 1$$#. ,+0.,) Figure 9Ć9:ăA14 I/O Board Block Diagram , .,* '*# /# ,+0.,))#. '*# /# ,+0.,))#. +0#.$ !# '!.,-.
Block Diagrams 601%+ %0%1 . %0%1 %,%/!1-/ 5%#21(3% /-#%00-/ %0%1 2+%/(# /-#%00-/ 51%,0(-, %0%1 2&&%/ !1#'%$ %*%#1 %0%1 -,1/-**%/ !1! 2&&%/ ,!"*% !1! 20 !,) 4(1#' !1! 2&&%/ $$/%00 20 $$/%00 2&&%/ -,1/-* 20 -,1/-* 2&&%/ /-+ ,1%//2.1 -,1/-**%/0 $$/%00 %#-$% %*%#1 - $$/%00 !1#'%0 %*%#1 !1#'%0 5%#21(3% 601%+ !1! 20 5%#21(3% 601%+ $$/%00 20 5%#21(3% 601%+ -,1/-* 20 - -7+(#/-./-#%00-/ ,1%//2.
Block Diagrams ,)* $ ( )) * &%- &# *!# $ ( )) * ) ** (, "+' ( )) & % $&(, # * !* * * % ( *&( $&(, &% ! +( *!&% " $&(, * + () !* * * ! %&)*! ) &%*(&# &* ( & ( &%% *&( Figure 9Ć12:ăA18 Memory Board Block Diagram 9Ć16 Diagrams
Block Diagrams $' , )(-+)&& + ) + -+) (, & - -+) (, '*&$(" -+) (, -+) (, -+) ,% 0 )&- " , -+) +$/ ) + -+) ,% 0 '*&$(" )'* +-' (-, '*&$(" -+) $"( &, .
Block Diagrams )1 1- )',!* &&0%1 !+.*),' %!$ ,.210 + )1 1- !/)!"*% !), ,.21 2&&%/ ,.21 2*1).*%4%/ 4 1- %,1%/ #!*% 2*1).*)%/ 4 1- 4 !), ), -,3%/1%/ /1 /+ /" &&0%1 -//%#1)-, )1 + 1- + -+.!/!1-/ %3%* )1 1- /!,0)1)-, -')# )1 2+"%/ -+.
Replaceable Parts "#+ + ,#(' (', #'+ %#+, ( ," * )% % (&)(' ',+ (* ," + + *# %(/ -+ ,"#+ %#+, ,( # ',# 1 ' (* * * )% & ', ) *,+ Parts Ordering Information )% & ', ) *,+ * . #% % *(& (* ,"*(-!" 1(-* %( % $,*('#0 ' + *.# ', * (* * )* + ', ,#. " '! + ,( $,*('#0 #'+,*-& ',+ * +(& ,#& + & ,( (&&( , #&)*(. (&)(' ',+ + ," 1 (& . #% % ' ,( !#. 1(- ," ' #, ( ," % , +, #* -#, #&)*(.
Replaceable Parts Using the Replaceable Parts List * +" ( $ %(# * %$ $ * &" " (*) )* ) (( $ %( '+ ! ( *( , " $ ()* $ $ * )*(+ *+( $ *+( ) % * " )* - "" "& /%+ $ * "" * $ %(# * %$ /%+ $ %( %( ( $ ( &" # $* & (*) Item Names $ * &" " (*) )* $ * # # ) ) & ( * (%# * ) ( &0 * %$ / %"%$ +) % )& " # * * %$) $ * # # # / )%# 0 * # ) && ( ) $ %#&" * %( +(* ( * # # $* * %$ ( " * "%
Replaceable Parts TableĂ10Ć1:ăBoard FRUs CSA 803A Service Manual FRU Part Number Description 31.#& 1*5& .6&1 4//+8 22&,#+8 .6&1 .--&$3 &(4+"3.1 .4$) "-&+ 22&,#+8 .3 &/+"$&"#+& 1%&1 1.-3 "-&+ .-31.+ 1.-3 "-&+ 433.- -/43 43/43 &,.
Replaceable Parts CROSS INDEX - MFR. CODE NUMBER TO MANUFACTURER Mfr.
Replaceable Parts CROSS INDEX - MFR. CODE NUMBER TO MANUFACTURER Mfr.
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts 4 5 3 2 1 18 14 17 15 16 7 3 6 8 16 6 15 14 7 9 13 4 10 12 11 Figure 10Ć1:ăCabinet CSA 803A Service Manual 10Ć7
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty 12345 Name & Description Mfr. Part No. $ " # " # ! % " # $ Mfr.
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts 1 2 3 A12 4 5 6 7 8 9 10 5 11 5 29 38 A10 12 37 16 33 13 16 36 32 A7 14 35 5 34 15 33 16 31 2 30 2 29 18 17 19 28 20 27 21 26 2 2 25 24 2 22 23 Figure 10Ć3:ăChassis, Rear CSA 803A Service Manual 10Ć11
Replaceable Parts Fig. & Index No. Tektronix Part No. $$ ") ") & $ $ %# ' " & #$ !" ## " # ! " ! " % # # # %#$ #$ " % & " % $ ##) $ " # ( $ Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts 3 4 2 1 A13 5 A4 1 6 7 8 9 22 A17 21 A18 20 A14 19 A15 12 18 17 12 16 10 A3 11 A8 15 12 12 13 A1 14 A5 12 Figure 10Ć4:ăCircuit Boards CSA 803A Service Manual 10Ć13
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts A27 A28 A20 A21 A22 A23 A19 A26 Figure 10Ć5:ăAcquisition Module CSA 803A Service Manual 10Ć17
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty 12345 Name & Description Mfr. Code Mfr. Part No.
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts Fig. & Index No. Tektronix Part No. Serial No. Effective Dscont Qty Mfr. Code 12345 Name & Description Mfr. Part No.
Replaceable Parts 1 2 6 5 3 4 Figure 10Ć7:ăAccessories CSA 803A Service Manual 10Ć21
Replaceable Parts 10Ć22 Mechanical Parts List
