Datasheet

Characteristics
TDS3000C Series Electrical Characteristics
TDS3012C TDS3014C TDS3032C TDS3034C TDS3052C TDS3054C
Bandwidth 100 MHz 100 MHz 300 MHz 300 MHz 500 MHz 500 MHz
Calculated Rise 3.5 ns 3.5 ns 1.2 ns 1.2 ns 0.7 ns 0.7 ns
Time (typical)
Input Channels 2 42424
External Trigger Input Included on all models
Sample Rate on 1.25 GS/s 1.25 GS/s 2.5 GS/s 2.5 GS/s 5 GS/s 5 GS/s
Each Channel
Record Length 10 k points
Vertical Resolution 9 bits
Vertical Sensitivity, 1 MΩ 1 mV/div to 10 V/div
Vertical Sensitivity, 50 Ω 1 mV/div to 1 V/div
Input Coupling AC, DC,GND
Input Impedance 1 MΩ in parallel with 13 pF or 50 Ω
DC Gain Accuracy +
2%
Maximum Input Voltage,1 MΩ 150 V
RMS
with peaks at < 400 V
Maximum Input Voltage,50 Ω 5 V
RMS
with peaks at < 30 V
Position Range + 5 div
Bandwidth Limit 20 MHz 20 MHz 20 MHz, 150 MHz 20 MHz, 150 MHz 20 MHz, 150 MHz 20 MHz, 150 MHz
Time Base Range 4 ns to 10 s 4 ns to 10 s 2 ns to 10 s 2 ns to 10 s 1 ns to 10 s 1 ns to 10 s
Time Base Accuracy +20 ppm over any 1 ms time interval
Input/Output Interfaces
Ethernet Port RJ-45 connector, supports 10Base-T LAN
USB Port Front-panel USB 2.0 host port
Supports USB flash drive
GPIB Port Full talk/listen modes, setting and measurements
(Optional with TDS3GV Communications Module)
RS-232-C Port DB-9 male connector, full talk/listen modes; control of all modes, settings and measurements
Baud rates up to 38,400
(Optional with TDS3GV Communications Module)
VGA Video Port DB-15 female connector, monitor output for direct display on large VGA-equipped monitors
(Optional with TDS3GV Communications Module)
External Trigger Input BNC connector, input impedence > 1 MΩ in parallel with 17 pF; max input voltage is 150 V
RMS
Acquisition Modes
DPO – Captures and displays complex waveforms,
random events and subtle patterns in actual signal
behavior. DPOs provide 3 dimensions of signal infor-
mation in real time:Amplitude, time and the distribu-
tion of amplitude over time.
Peak Detect – High frequency and random glitch
capture. Captures glitches as narrow as 1 ns (typical)
using acquisition hardware at all time base settings.
WaveAlert
®
– Monitors the incoming signals on all
channels and alerts the user to any waveform that
deviates from the normal waveform being acquired.
Sample – Sample data only.
Average – Waveform averaged, selectable
from 2 to 512.
Envelope – Min-max values acquired over one
or more acquisitions.
Single Sequence – Use the Single Sequence
button to capture a single triggered acquisition
sequence at a time.
Trigger System
Main Trigger Modes – Auto (supports Roll Mode for
40 ms/div and slower), Normal,Single Sequence.
B Trigger – Trigger after time or events.
Trigger After Time Range – 13.2 ns to 50 s.
Trigger After Events Range – 1 to 9,999,999 events.
Trigger Types
Edge – Conventional level-driven trigger. Positive or
negative slope on any channel. Coupling selections:
AC, DC,Noise Reject, HF Reject,LF Reject.
Video – Trigger on all lines or individual lines,
odd/even or all fields on NTSC, PAL, SECAM.
Extended Video – Trigger on specific lines in broad-
cast and non-broadcast (custom) standards and on
analog HDTV formats (1080i, 1080p,720p, 480p).
Requires TDS3VID or TDS3SDI application module.
Pulse Width (or Glitch) – Trigger on a pulse width
<, >, =,≠ to a selectable time limit ranging from
39.6 ns to 50 s.
Runt – Trigger on a pulse that crosses one
threshold but fails to cross a second threshold
before crossing the first again.
Slew Rate – Trigger on pulse edge rates that are
either faster or slower than a set rate. Edges can be
rising, falling or either.
Pattern – Specifies AND,OR, NAND,NOR when true
or false for a specific time.
State – Any logic state.Triggerable on rising or
falling edge of a clock. Logic triggers can be used
on combinations of 2 inputs (not 4).
Comm – Provides isolated pulse triggering required
to perform DS1/DS3 telecommunications mask
testing per ANSI T1.102 standard. Requires
TDS3TMT application module.
Alternate – Sequentially uses each active channel
as a trigger source.
TDS3000C • www.tektronix.com/oscilloscopes
3
Digital Phosphor Oscilloscopes
TDS3000C Series