Datasheet

OSCILLOSCOPE SELECTION GUIDE
8 | TEK.COM
DPO70000SX DSA8300
Additional Resources
Channels
2 or 4 analog channels
Six modules support up to 8 single ended or
4 differential channels and/or 2 optical channels
Bandwidth
23 GHz to 70 GHz
Up to 70+ GHz Electrical bandwidth and 80+ Optical bandwidth
modules available with intrinsic jitter as low as <100 fs RMS
Sample Rate
50 GS/s to 200 GS/s 300 ks/s Maximum sample rate
Max Record
Length
Up to 1Gpoints
50 to 16,000 per channel native record length; with up to
1M points when using available IConnect Signal Integrity
Software, 10M samples (100k unit intervals, 100 samples
per unit interval) when equipped with available 80SJNB
Jitter, Noise and BER Analysis software
Trigger Types
Pinpoint
™
Triggering, Edge, Glitch, Pulse Width, Runt, Time-out,
Transition, Setup/Hold, Pattern, State, Window, Trigger Delay
(by Time and by Event), Visual Trigger*
*Optional
Clock Input/Prescale Trigger, TDR clock (generated
internally), Clock Recovery from Optical Sampling modules
and Electrical Clock Recovery modules, and Phase
Reference time base supports acquisitions Free Run mode
and Trigger Direct Input for <100 fs RMS intrinsic jitter typical
Optional Serial Bus
Decode and Analysis
SR-COMP: RS-232/422/485/UART; SR-EMBD: I2C, SPI; SR-ENET:
10/100Base-T Ethernet SR-PCIE: PCI Express; SR-USB: USB; SR-810B: 8b/10b
80SJNB Jitter, Noise, BER, Serial Data Link and PAM4 Analysis
Software; IConnect Signal Integrity Software; 100GBASE-SR4
Transmitter & Dispersion Eye Closure (TDEC) Automation Test Solution
Connectivity
USB2.0 Host (4 on front)/3.0 Host (4 on rear), USB Device, LAN
(10/100/1000 Base-T Ethernet, LXI Class C Compliant), DVI, VGA,
DisplayPort (2)
3 USB 2.0 Port(s) connector on the front panel, 4 USB 2.0 Ports
on the rear panel; LAN PORT, RJ-45 connector, supports
10BASE-T, 100BASE-T, 1000BASE-T on rear panel;
1 Serial Port, DB-9 COM1, COM2 ports; 1 DVI IEEE488.2
connector on rear panel; 1 DVI connector, female on rear panel,
DVI to VGA 15-pin D-sub connector adapter provided; PS2
Serial Ports Mouse and keyboard inputs; Audio Ports 1/8 in.
microphone input and line output
Waveform Math
and Analysis
53 Automated Measurements, Waveform and Screen Cursors, Arithmetic and
Advanced Waveform Math, FFT, Measurement Statistics, Waveform Histograms
Optional: DPOJET Noise, Jitter and Eye Analysis Tools; Frequency Counter-Timer;
PAM4 Transmitter Analysis Software; Serial Data Link Analysis; 10G/40G/100G
KR4/CR4 Transmitter Compliance; DDR Memory Bus Analysis; DisplayPort 1.2/1.4
Test Software; MIPI D-PHY Transmitter Debug and Compliance Test Solution;
EDP Compliance Test Package; Ethernet Compliance Testing; Fiber Channel
Essentials; HDMI 2.0 Analysis and Compliance; High Speed Serial Link Training
Analysis; HDMI Compliance Testing; MIPI M-PHY Debug and Compliance Test;
NBASE-T TekExpress Conformance and Debug Software; PCI Express Gen1/2/3/4
TekExpress Compliance/Debug; Power Measurement and Analysis Software;
SAS-3 Tx Compliance Test; SATA PHY Transmitter Test; SignalCorrect Cable,
Channel, and Probe Compensation Software; SFP+ Compliance and Debug
Solution; Embedded Serial Triggering and Analysis (I2C, SPI); USB 2.0/3.0/3.1
Automated Compliance Test; SignalVu Vector Signal Analysis
Over 120 automated measurements include RZ, NRZ, and
pulse signal types, and the following measurement types, plus
8 math waveforms using the following math functions: Add,
Subtract, Multiply, Divide, Average, Differentiate, Exponential,
Integrate, Natural Log, Log, Magnitude, Min, Max, Square
Root, and Filter. In addition, measurement values can be
utilized as scalars in math waveform definitions; Mask support
for many applications, standard masks are available as
predefined, built-in masks; Automated Masked Margin based
on Mask Hit Ratio as required by many standards.
Software
Optional: TekScope Anywhere
™
Windows
®
7 Ultimate (32-bit) Operating System; IConnect
Signal Integrity Software for frequency domain analysis,
S-parameter measurements, and impedance characterization
80SJNB Jitter, Noise, BER, and Serial Link analysis including
Cross-Talk aware TJ (BUJ and PAM4 Analysis); 80SJARB Jitter
Analysis of Arbitrary Data with J2-J9 measurements, and
support for pattern lengths to PRBS31; 100GBASE-SR4 (IEEE
802.3bm) optical transmitter characterization measurements,
including TDEC, signaling rate, Average Launch Power, OMA,
ER, Transmitter Eye Mask
Upgrade
• Increase bandwidth
• Upgrade older platforms to the latest platforms
• Add extended record length, up to 1 G points
• Add measurements and analysis
(jitter, mask, RF)
• Modular architecture lets you add channels or bandwidth
• Add TDR, optical and electrical standards support
• Add advanced analysis, compliance test, frequency domain
analysis software
• Add clock recovery trigger pickoff (CRTP) to select optical modules
• Enhance system jitter floor performance to <100 fs RMS
ADVANCED SIGNAL ANALYSIS
AND SAMPLING OSCILLOSCOPES