Datasheet

Arbitrary Fun ction G enerators — AFG3000C Series
Characteristic AFG3011C AFG3021C
AFG3022C
AFG3051C
AFG3052C
AFG3101C
AFG3102C
AFG3251C
AFG3252C
Other Waveforms
1µHzto100kHz 1µHzto500kHz 1μHz to 800 kHz 1 µHz to 1 MHz 1 µHz to 2.4 MHz
NoiseBandwidth(-3dB)
10 MHz 25 MHz 50 MHz 100 MHz 240 MHz
Noise type
White Gaussian
Internal Noise Add
When activated, output signal amplitude is reduced to 50%
Level
0.0% to 50% of amplitude (V
p-p
) setting
Resolution
1%
DC (into 50 Ω)
-10Vto+10V -5Vto+5V –5Vto+5V -5Vto+5V -2.5Vto+2.5V
Arbitrary Waveforms
1 mHz to 5 MHz 1 mHz to 12.5 MHz 1 mHz to 25 MHz 1 mHz to 50 MHz 1 mHz to 120 MHz
Arbitrary waveforms in
Burst Mode
1mHzto2.5MHz 1mHzto6.25MHz 1mHzto12.5MHz 1mHzto25MHz 1mHzto60MHz
Effective analog
bandwidth (-3 dB)
8 MHz 70 MHz 100 MHz 225 MHz
Nonvolatile memory
4 waveforms
Memory: Sample rate
(1K=1024 points)
2to128K:250MS/s 2to128K:250MS/s 2to16K:1GS/s
>16 K to 128 K: 250 MS/s
2to16K:1GS/s
>16Kto128K:250MS/s
2to16K:2GS/s
>16 K to 128 K: 250 MS/s
Vertical resolution 14 bits
Rise/Fall time
≤80 ns ≤14 ns ≤10 ns ≤8ns ≤3ns
Jitter (RMS), typical
4ns 4ns
1nsat1GS/s
4nsat250MS/s
1nsat1GS/s
4nsat250MS/s
500 ps at 2 GS/s
4nsat250MS/s
Ampli
tude
Range (50 Ω load)
20 mV
p-p
to 20 V
p-p
10 mV
p-p
to 10 V
p-p
10 mV
p-p
to 10 V
p-p
20 mV
p-p
to 10 V
p-p
≤200 M
Hz: 50 mV
p-p
to5V
p-p
>200 M
Hz: 50 mV
p-p
to4V
p-p
Range (open circuit or
High Z)
40 mV
p-p
to 40 V
p-p
20 mV
p-p
to 20 V
p-p
20 mV
p-p
to 20 V
p-p
40 mV
p-p
to 20 V
p-p
≤200 MHz: 100 mV
p-p
to 10 V
p-p
>200 MHz: 100 mV
p-p
to8V
p-p
Accuracy
±(2% of setting +2 mV)
(1kHzsinewave,0V
offset, >20 mV
p-p
amplitude)
±(1% of setting +1 mV) (1 kHz sine wave, 0 V offset, >10 mV
p-p
amplitude)
Resolution 0.1 mV
p-p
,0.1mV
RMS
, 1 mV, 0.1 dBm or 4 digits
Units
V
p-p
,V
RMS
, dBm (sine wave only) and Volt (high/low setting)
Output impedance 50 Ω
Load impedance setting
Selectable: 50 Ω,1Ω to 10.0 kΩ, High Z (Adjusts displayed amplitude according to selected load impe dance)
Isolation <42 V
pk
maximum to earth
Short-circuit protection Signal outputs are robust against permanent shorts against floating ground
External voltage
protection
To protect signal outputs against external voltages use fuse adapter 013-0345-xx
DC Offset
Range (50 Ω load) ±(10 V
pk
–Amplitude
pp
/2) ±(5 V
pk
– Amplitude
pp
/2) ±(5 V
pk
– Amplitude
pp
/2) ±5 V
pk
DC ±2.5 V
pk
DC
Range (open circuit or
High Z)
±(20 V
pk
–Amplitude
pp
/2) ±(10 V
pk
– Amplitude
pp
/2) ±(10 V
pk
– Amplitude
pp
/2) ±10 V
pk
DC ±5 V
pk
DC
Accuracy
±(2% of |setting| + 10 mV +
1% of amplitude (V
p-p
))
±(1% of |setting| + 5 mV + 0.5% of amplitude (V
p-p
))
Resolution 1 mV
www.tektronix.com 3