Datasheet

Datasheet
Characteristics
General
Characteristic
Description
Channels
1
Waveforms Sine, Square, Pulse, Ramp, Noise, DC, Sin(x)/x, Gaussian,
Lorentz, Exponential Rise, Exponential Decay, and
Haversine
Sine Wave
1 μHz to 20 MHz
Sine Wave in
Burst Mode
1 μHz to 10 MHz
Effective
Maximum
Frequency Out
20 MHz
Amplitude Flatness (1 V
p-p
)
<5 MHz ±0.15 dB
5 MHz to 20 MHz ±0.3 dB
Harmonic Distortion (1 V
p-p
)
10 Hz to 20 kHz <–70 dBc
20 kHz to 1 MHz <–60 dBc
1 MHz to 10 MHz <–50 dBc
10 MHz to
20 MHz
<–40 dBc
THD
<0.2% (10 Hz to 20 kHz, 1 V
p-p
)
Spurious (1 V
p-p
)
10 Hz to 1 MHz <–60 dBc
1 MHz to 20 MHz <–50 dBc
Phase Noise,
Typical
20 MHz: <–110 dBc/Hz at 10 kHz offset, 1 V
p-p
Residual Clock
Noise
–63 dBm
Square Wave
1 μHz to 10 MHz
Rise/Fall Time
≤18 ns
Jitter (RMS),
Typical
<500 ps
Ramp Wave 1 μHz to 200 kHz
Linearity
≤0.1% of peak output at 10% to 90% of amplitude range
Symmetry 0.0% to 100.0%
PulseWave 1mHzto10MHz
Pulse Width 30.00 ns to 999.99 s
Resolution 10 ps or 5 digits
Pulse Duty
0.001% to 99.999% (Limitations of pulse duty width apply)
Edge Transition
Time
18 ns to 0.625 × Pulse Period
Resolution 10 ps or 4 digits
Lead Delay
Range
Continuous Mode: 0 ps to Period
Trigger/Gate Burst Mode: 0 ps to Period – [Pulse Width + 0.8
× (Leading Edge Time + Trailing Edge Time)]
Resolution 10 ps or 8 digits
Overshoot,
Typical
<5%
Jitter (RMS),
Typical
<500 ps
Characteristic
Description
Other Waveforms
1 μHz to 200 kHz
Noise Bandwidth
(–3 dB)
20 MHz
Noise Type
White Gaussian
DC (into 50 Ω)
–5Vto+5V
Arbitrary Waveforms
1mHzto10MHz
Arbitrary
Waveforms in
Burst Mode
1mHzto5MHz
Effective A nalog
Bandwidth
(–3 dB)
34 MHz
Nonvolatile
Memory
4 waveforms
Memory: Sample
Rate
2 to 128k: 250 MS/s
Vertical
Resolution
14 bits
Rise/Fall Time
≤20 ns
Jitter (RMS)
4ns
Amplitude, 50 Ω
Load
10 mV
p-p
to 10 V
p-p
Amplitude, Open
Circuit
20 mV
p-p
to 20 V
p-p
Accuracy
±(1% of setting + 1 mV), (1 kHz sine waveform, 0 V offset,
>10 mV
p-p
amplitude)
Resolution 0.1 mV
p-p
,0.1mV
RMS
,1mV,0.1dBm,or4digits
Units
V
p-p
,V
RMS
,dBm(sinewaveonly)
Output
Impedance
50 Ω
L
oad Impedance
S
etting
Selectable: 50 Ω,1Ω to 10.0 kΩ, High Z (adjusts displayed
amplitudeaccordingtoselectedloadimpedance)
Isolation <42 V
Peak
maximum to earth
Short-circuit
Protection
Signal outputs are robust against permanent shorts against
floating ground
External Voltage
Protection
To protect signal outputs against external voltages use fuse
adapter 013-0345-00
DC Offset Range,
50 Ω Load
±(5 V
Peak
–amplitudeV
p-p
/2)
DC Offset Range,
Open Circuit
±(10 V
Peak
–amplitudeV
p-p
/2)
Accuracy
±(1% of |setting| + 5 mV + 0.5% of amplitude (V
p-p
))
Resolution 1 mV
4 www.tektronix.com