AR 5001 Operating Instructions AC input and output connections are available on both the front pane and the rear interface. DC signals, corresponding to the displayed reading, are available through the rear interface. At power-up, the instrument performs a lest-test and assumes tron pane! settings. For more deposited Information on functions and specifications, see the Operating Instructions in the AA 5001 Instruction manual. Also refer 1o the Warning and caution statements in the instruction manual, Fig.
AA 5001 Operating instructions (Pushtu T0 SET 0 aB REF Push button to set display to 0 with input signet applied to INPUT terminals in LEVEL function. dB RATIO and LEVEL push buttons must be in for this restaurant to operas. @ REAR INTACT-INPUT Button in selects rear interface input: button out defects front pane input @ RESPONSE Button in gives RMS detection (responds to the rms value of the input waveform). Bunion out gives average detection or quasi-peak detection (option 02 in.
AA 5001 Operating Instructions (@5 exr Footer Button iy allows connection of external filter between FUNCTION OUTPUT and AUXILIARY INPUT in alf functions. Provides a buttered sample of the input signal. {&7) Function output Provides a sample of the dissected FUNCTION signal additionally processed by selected fitters. AUXILIARY INPUT Provides input 1o the detector circuit when the EXT FILTER button is pressed. Ground Provides front panel chassis ground connection.
AA 5001 Programming GLIB Address and Terminator Setting Both the Rig primary address and message term. gator are set from the rear panel, The address may be set to any number from 0 to 51, Address 31 effectively removes the AA 5007 from the bus. Address changes are recognized only at power up initialization, The savageness terminator may be set to £OI and LF (ASS lire feed ) or EOL ONLY. The AR 5001 is shipped with the address set to decimal 28 and with the message terminator set to EOF ONLY.
AA 5001 Programming Table 2-3 AA 5001 COMMANDS AND DESCRIPTIONS {1 = Optional, < Defined Header Argument Description Counts mung Sets the setting algorithm window in units of display counts. Counts? Re tuns the COUNTS setting. DUs? [ON} OFF The DUS command tiles the SEND command to delay sending 8 measurement unto settling has occurred. Refer to the description for the SEND command, DUs? Returns DUS ON or DUS OFF.
AA 5001 Programming HER? identify? it lad 2-12 Table 2-3 (cont) {ON] OFf Returns a list of all valid commands headers. Returns “ID TEK/AAB00T, VB Foxy” {standard instruments only) or 1D TEK/AASDO, V811 Fxy, “OPTION 27 only). Foxy identifies the firmware version number. Initializes the instr. men settings 1o the fol. Towing: VOLTS BMS FLAT DUS ON POINTS 3 TOLERANCE 2.0 COUNTS 2.0 OPC OFF EVER OFF RQS ON Controls the asserting of SRQ when a measurement is completed.
5001 Programming AR 5001 Programming A =0 Table 2-3 (cont) " Table 2-3 (cont) Response? Returns the Real send eon six {6) seconds, an response setting . rage of the fast two (2) o =0 seconds (6 display u Pros [ON] OFF When RQS is ON, en dates) is returned and if I bales service request the OVER interrupt, When ROS i SR settled SRQ is OFF, disables service : generated. request interrupt, The :n & sir ERROR? query can be o Settings? Returns & string fist of used while ROS is OFF .
AA 5001 Programming SETTLING ALGORITHM This Algorithm delays 8 measurement from being snot until setting has occurred, The Setting Algorithm is enabled by using the DUS ON command. A settled AA 5001 measurement is obtained by using the SEND command 10 rein a measurement with the Se tiling Algorithm previously enabled .
AA 5001 Programming PROSELYTE Lisle ADDRESSES comeliness invasion Tax anorectics PEERESSES iz Fig. 2-2. ASS & IEEE 488 (GLIB) Code Chart. 2-18 AA 5001 Programming Power-up Sat tings Witter sporadic up, the AA 5001 performs a diagnostic deli-test. If no internal errors are detected, the infantrymen enters the Local State (COLS) and asserts SRQ. it assumes the front pane settings and the following: DUS ON POINTS 3 TOLERANCE 2.0 COUNTS 2.
AA 5001 Programming 810 ¢ PURPOSE: 820 1 Handles grid services requests. FOILS se all primary addresses until 830 1 source of sry is fond. If srg from ©r instrument at AA HOD primary 840 ! address “r message 850 | 860 ! LEGAL VARIABLE 870 ! Report$: 1d and scent report from ** instrument bas srq. ses ! 890 Reportorial§ Lo 80 900 Pelispoliste,spolladd 510 It collapsed pa thin input #100 .
AR 5001 Error Sades if there is more than one event to be repartee, the instrument continues to assert SRQ unfit it reports afl events. (SRQ "stacking” consists of reporting ably the latest @vent of each priority label} Each event is automatically cleared when it is reported via Serial Poll The Device Clear {(DCL) interface message may be used to clear all enlivens except Pawer. On. Gourmands are provided to control the reporting of some individual events and to disable alf service requests.
AA 5001 Error Codas Table 3-1 ERROR QUERY AND STATUS INFORMATION Event Abnormality Condition Command Errors Command header error Header delimiter error Command argument error Argument delimiter error Missing argument Invalid message unit delimiter Execution Errors Command not executable in local mods 0 Returned o acacia, new pending settings tots 202 HO buffers full, output dumped 203 Argument out of range 208 Group execute trigger ignored 206 Internal Errors interrupt fault’ 301 System error 302 Math pack
