MP1280 User Guide
User Guide Contents Overview............................................................... 1 Getting Started...................................................... 2 Unpacking myPower for iPhone 4..................... 2 Getting to Know myPower for iPhone 4............. 3 Using myPower for iPhone 4.................................. 4 Adhering myGuard™ Protector........................... 4 Placing Your iPhone 4 into the Battery Case...... 5 Removing Your iPhone 4 from the Battery Case......
Overview myPower™ for iPhone® 4, the ultra slim rechargeable battery case for iPhone 4, lets you talk, rock, view, share, and stay connected longer. This compact battery case doubles as a dock for automatic syncing, and as a case to protect your iPhone 4 from everyday wear and tear. Equipped with an efficient lithium polymer battery, myPower for iPhone 4 preserves your iPhone 4 battery by bypassing the battery and directly powering (rather than charging) your iPhone 4.
Getting Started Unpacking myPower for iPhone 4 Your myPower for iPhone 4 package includes the following: User guide (not shown) myGuard™ protector set (not shown) myPower for iPhone 4 Micro USB cable 2 MP1280
Getting to Know myPower for iPhone 4 Raised edge for iPhone 4 surface protection Replaceable battery module Control module Micro USB port for charging and automatic syncing USER GUIDE On/off switch preserves power Capacity indicator shows remaining power at a glance 3
Using myPower for iPhone 4 Use myPower for iPhone 4 to power your iPhone 4, or to charge your iPhone 4 while connected to external power. myPower for iPhone 4 bypasses the iPhone 4 battery to power (not charge) your iPhone 4, thus extending the overall life of the iPhone 4 battery. The battery will not charge iPhone 4 unless connected to an external power source. myPower for iPhone 4 is charged in two ways: by connecting to external power via a USB power adapter, or by connecting to a computer USB port.
case and the iPhone 4 back, it is very important that you adhere the protector onto the back of your iPhone 4. This will prevent any scratches on the back when the iPhone 4 is in or out of our battery case. Additional myGuard protectors are available online at www.tekkeon.com. 1. Ensure that your iPhone 4 is free of dust. 2. Holding the red label , peel the first backing from the myGuard protector. 3. Position and adhere myGuard to the back of your iPhone 4. 4.
3. Slide the battery module down over your iPhone 4 until it snaps into place. 4. When you’re ready to use the battery, slide the On/Off switch to the On position (to the right). The battery icon on your iPhone 4 will change to to indicate your iPhone 4 is being externally powered. 5. Use your iPhone 4 as you would normally. The iPhone 4 battery will not be used while iPhone 4 is in the case until myPower for iPhone 4 is empty, or you slide the power switch to off.
Removing Your iPhone 4 from the Battery Case 1. Gently pull the battery module from the control module to separate the two pieces. 2. Slide your iPhone 4 away from the 30-pin connector in the control module. 3. To store myPower for iPhone 4, slide the battery module onto the control module until it snaps into place or store the two pieces separately.
1. With or without your iPhone 4 inserted in the battery case, connect the micro USB connector to the micro USB port on myPower for iPhone 4. 2. Connect the USB connector to a wall outlet using a USB power adapter or to a computer USB port. The battery capacity indicator will turn to red to indicate myPower for iPhone 4 is being charged. If connected, your iPhone 4 battery icon will change to to indicate your iPhone 4 is being charged. 3.
Note: If you are charging iPhone 4 at the same time, you must use an iPhone 4-compliant USB adapter. Syncing Your iPhone 4 The intelligent design of myPower for iPhone 4 enables you to sync your iPhone 4 while charging it via a USB port on your computer. 1. With your iPhone 4 inserted in the battery case, connect the micro USB connector to the micro USB port on myPower for iPhone 4. 2. Connect the USB connector to a USB port on a computer.
Prolonging Battery Life Extreme heat and cold will affect your battery’s performance. At temperatures above 80°F (27°C), the battery will discharge more quickly, and in colder temperatures, the battery won’t charge well. Therefore, it is recommended that the battery is used at room temperature, or between 68°F to 77°F (20°C to 25°C), and is not used in temperatures outside the range of temperatures between 32°F to 104°F (0°C to 40°C).
Ultra Power battery which more than doubles your work or play time on your iPhone 4. 1. With the iPhone 4 in the battery case, gently pull the battery module from the control module and iPhone 4. 2. Slide the new battery module down over your iPhone 4 until it snaps into place. Note: You must charge your extra battery before swapping it while on the go. Troubleshooting If myPower for iPhone 4 does not power iPhone 4, take these steps: 1. Confirm that the On/Off switch is in the On position (to the right).
Accessories The following accessories for myPower for iPhone 4 can be ordered at the Tekkeon online store at www.tekkeon.com: Ultra Slim Replaceable Battery MP1280-12 Ultra Power Replaceable Battery MP1280-22 myCharger USB Power Adapter MP1650-40 Safety Precautions Do not shake, drop, or throw the battery. (Avoid rough handling, or excessive shock and vibration.) • Do not puncture or crush the battery. • Do not burn or short circuit the battery.
Limited Warranty The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase. In the event of a defect in operation during the warranty period Tekkeon, Inc. will replace the defective product when the owner returns all product contents. The limited warranty will be considered void if the unit is tampered with, subject to misuse, negligence or accidental damage, has been improperly serviced, or if the security seal is removed.
Customer Support Customer support for myPower for iPhone 4 is available at: Tekkeon, Inc. c/o myPower for iPhone 4 3002 Dow Avenue, #134 Tustin, CA 92780 888-787-5888 / 714-832-1266 Tekkeon, Inc. must issue a Return Merchandise Authorization (RMA) number for all exchanges or refunds. www.tekkeon.com © 2010 Tekkeon, Inc. All Rights Reserved. Rev A Patent Pending. myPower and eSwap are trademarks of Tekkeon, Inc. Specifications are subject to change without notice. iPhone is a trademark of Apple Inc.
