et6000_ug_fnl 10/26/06 4:17 PM Page 1 Handsfree Bluetooth Speakerphone ® ET6000 User Guide
et6000_ug_fnl 10/26/06 4:17 PM Page 2
et6000_ug_fnl 10/26/06 4:17 PM Page 1 USER GUIDE Contents Overview..............................................................................................................................2 Getting Started ....................................................................................................................2 Unpacking ezSpeak ........................................................................................................2 Getting to Know ezSpeak ................................
et6000_ug_fnl 10/26/06 4:17 PM Page 2 Overview ezSpeak ™ by Tekkeon is a Bluetooth® speakerphone with a digital display that gives you the freedom to cut loose from your Bluetooth mobile phone. With advanced features like stored number redial, last number redial and voice dialing, you can use ezSpeak to make and receive calls without ever touching your mobile phone. And, you can use ezSpeak in your car, at home, or anywhere that is convenient for you. ezSpeak is designed with Bluetooth v1.
et6000_ug_fnl 10/26/06 4:17 PM Page 3 Getting to Know ezSpeak Volume Up/Volume Down Increases the speaker volume, mutes/unmutes the microphone, and enables scrolling through stored numbers Charging Lamp Indicates when ezSpeak is being charged or fully charged Digital Display Provides caller ID, call status, indication of device connection, volume level, and low battery indication Speaker Answer Button Used to initiate pairing, connect/disconnect the paired phone, and make/receive calls USER GUIDE M
et6000_ug_fnl 10/26/06 4:17 PM Page 4 Setting Up ezSpeak Before using ezSpeak, you must: • Charge ezSpeak • Pair ezSpeak to your mobile phone • Mount ezSpeak to your visor (for in car use) Directions for each of these activities are provided in the following three sections. Once these steps are completed, you will be ready to use ezSpeak! Charging ezSpeak Before using ezSpeak, you must charge the device for a minimum of two hours.
et6000_ug_fnl 10/26/06 4:17 PM Page 5 Pairing ezSpeak to Your Mobile Phone Pairing is the process of linking ezSpeak with your Bluetooth mobile phone or other Bluetooth device that supports a headset and/or handsfree profile. Before using ezSpeak with your mobile phone you must pair the devices. After this process is complete, you can use ezSpeak with your paired mobile phone. You can pair ezSpeak with up to seven Bluetooth devices.
et6000_ug_fnl 10/26/06 4:17 PM Page 6 Mounting ezSpeak When used in a car, ezSpeak is designed to be mounted to your car visor. You can use the visor clip with or without the optional swivel clip. To Mount ezSpeak with the Visor Clip 1. Attach the visor clip to ezSpeak by sliding the clip into the bracket on the rear of ezSpeak as shown. 2. Slide the clip onto your car visor. To Mount ezSpeak with the Visor Clip and Swivel 1.
et6000_ug_fnl 10/26/06 4:17 PM Page 7 Using ezSpeak Powering ezSpeak To Turn On ezSpeak 1. Press and hold on the display. approximately two seconds until the display lights up and “ET6000” appears NOTE: To conserve power, the display will turn off after being idle for approximately eight seconds. To view the display, simply press . To Turn Off ezSpeak 1. Press and hold ezSpeak turns off.
et6000_ug_fnl 10/26/06 4:17 PM Page 8 To Make Calls Using Voice Dialing (if supported by your mobile phone) . “Voice Dial” appears on the display and your phone is put into voice dialing mode. 1. Press 2. After you hear a beep (usually between one to four seconds), speak the name of the person you wish to call. You will hear the spoken name (if provided by your phone) and the call is automatically connected to ezSpeak.
et6000_ug_fnl 10/26/06 4:17 PM Page 9 To Receive a Call 1. When you hear ring tone or see “Ringing” and the calling number (if provided) on the display, press . The call is automatically connected to ezSpeak and “Call Active” appears in the display. To Reject an Incoming Call (if supported by your mobile phone) 1. When you hear ring tone or see “Ringing” and the calling number on the display, press “Call Reject” appears on the display, and the call is sent to your voice mail. .
et6000_ug_fnl 10/26/06 4:17 PM Page 10 Transferring Calls You can transfer calls between your mobile phone and ezSpeak. To Transfer Calls from Your Mobile Phone to ezSpeak 1. With the call connected to your mobile phone, press . “Transferring” and the connected number appear on the display and the call is transferred to ezSpeak. To Transfer Calls from ezSpeak to Your Mobile Phone (if supported by your mobile phone) 1.
et6000_ug_fnl 10/26/06 4:17 PM Page 11 Muting ezSpeak You can mute and un-mute the microphone temporarily so that you cannot be heard by the connected party. To Mute ezSpeak 1. While in talk mode, press and hold the microphone is muted. approximately two seconds. “Mute” appears on the display and To Un-Mute ezSpeak 1. When the microphone is muted, press and hold microphone is no longer muted. USER GUIDE .
et6000_ug_fnl 10/26/06 4:17 PM Page 12 Troubleshooting Issue Solution When you initiate the Bluetooth device pairing feature on your mobile phone, your phone cannot find ezSpeak. Verify that ezSpeak is placed in pairing mode (“Ready to Pair” appears on the display). If not, place ezSpeak in pairing mode. ezSpeak is not communicating with your mobile phone. Ensure that ezSpeak is on and charged, and that you have paired it with your Bluetooth mobile phone.
et6000_ug_fnl 10/26/06 4:17 PM Page 13 Troubleshooting (continued) Issue Solution Your mobile phone does not accept voice commands when you are using ezSpeak. Ensure that your mobile phone supports this feature and is set to voice control mode. If your mobile phone supports voice dialing and you are in a noisy environment, dial the number from the mobile phone as the loud background noise may interfere with the voice commands. You are encountering poor reception via ezSpeak.
et6000_ug_fnl 10/26/06 4:17 PM Page 14 Limited Warranty The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase. In the event of a defect in operation during the warranty period Tekkeon, Inc. will replace the defective product when the owner returns all product contents.
et6000_ug_fnl 10/26/06 4:17 PM Page 15 FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
et6000_ug_fnl 10/26/06 4:17 PM Page 16 Customer Support If you product is in need of repair or replacement, please contact the Tekkeon Customer Support Center at: Tekkeon, Inc. c/o ezSpeak 3002 Dow Avenue, #134 Tustin, CA 92780 888-787-5888 / 714-832-1266 www.tekkeon.com Tekkeon, Inc. will issue a Return Merchandise Authorization (RMA) number for all repairs or exchanges.
et6000_ug_fnl 10/26/06 4:17 PM Page 17
et6000_ug_fnl 10/26/06 4:17 PM Page 18 www.tekkeon.com © 2006 Tekkeon, Inc. Rev A All Rights Reserved ezSpeak™ is a trademark of Tekkeon, Inc. Cut loose. Stay loose.
