NEW! Follow along with your smartphone to make assembly even easier! FitSpine LX Series Assembly Instructions TM Models LX4, LX5, LX6, LX7, LX8, LX9 For gravity-assisted stretching and decompression FULL 5 YEAR T Y W AR RA N To download and print the Teeter FitSpine LX™ instructions, visit the Product Manuals page at teeter. com. EN * Specifications may vary from this image and are subject to change without notice. The LX4 is shown here. Your actual model may vary.
Congratulations on your purchase of a Teeter FitSpine LX™ Series Inversion Table! For the best experience, it is critical that you follow the assembly instructions, read and fully understand the Owner’s Manual attached to the equipment, and review the Getting Started DVD prior to using your new Teeter Inversion Table. Teeter Decompression Devices are multiple user, reusable devices for home use, intended to provide traction to the spine while stretching the para-spinal muscle and soft tissues.
BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table. Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity. IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE ! WARNING FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.
Parts for Assembly Parts vary by model (noted) and are not shown to scale. Hardware drawings located on the insert inside each Hardware Kit. ITEM NO. ITEM NAME ITEM NO.
Understanding Your Inversion Table Before reading further, study the drawing below to familiarize yourself with the important components of your Teeter Inversion Table. 1 2 3 6 4 7 5 Located on back of table bed. 8 13 14 9 12 11 17 15 The LX4 is shown here. Your actual model may vary.
Safety Warning Labels & Product Specifications Important: Please review all labels and supporting materials before using your inversion table. This drawing indicates the locations of the warning labels found on your product. If a label is missing, illegible or is removed, contact Teeter Customer Service to request a complimentary replacement label. Note: Image and labels below not shown at actual size. 57.0 in (144.8 cm) 60.8 in (154.4 cm) 27.5 in (69.9 cm) The LX4 is shown here.
Before Beginning Assembly Unpack and Prepare Your Workspace • If possible, assemble the equipment at or near the space in which you intend to use it to avoid moving it later. • Unpack all parts and support materials. Set aside packing materials and clear your work area. • Locate the Hardware Kits packaged with the manuals. They are labeled to correspond with the assembly process. • The Getting Started DVD provides step-by-step instruction on how to assemble your product.
For All Models STEP 1 Assemble Boarding Platform IMPORTANT: Do not fully tighten the bolts until all the bolts have been screwed in and the platform is properly aligned. FIGURE 1 • Remove the A-frame from the box and place it on its back side so that the open ends of the A-Frame are pointing up (Figure 1). • Locate the Boarding Platform and the Boarding Platform Hardware Kit, including (2) Rubber Feet and (4) Boarding Platform Bolts.
For All Models STEP 2 Assemble Handles and Handle Brackets NOTE: If your Teeter came with an optional Caddy (included with the LX9), stop here and open the Caddy packaging. Follow the included instructions to attach the Caddy to the Left Handle before assembling the Handles to the A-Frame. FIGURE 5 IMPORTANT: Do not fully tighten the bolts until all the bolts have been screwed into the Handles AND the Handle Brackets.
For All Models STEP 3 Assemble Roller Hinges to Table Bed NOTE: Some models come with Traction Handles pre-assembled to the Roller Hinges. The assembly instructions detailed below still apply. FIGURE 10 UNLOCKED Pivot Pin Bracket Pin LOCKED Bracket Cam Lock • Familiarize yourself with the 3-Hole Roller Hinge and Cam Lock terms (Figure 10). ! WARNING NEVER disassemble the Roller Hinge Pivot Pin.
For All Models STEP 4 Assemble Table Bed to A-Frame • Face the front of the A-Frame where the Crossbar is located (Figure 15). FIGURE 15 • Grasp both Roller Hinges, right above the Cam Lock, and lift the Table Bed. Allow the top of the Table Bed to rotate toward the floor so that the back of the Table Bed is now facing you and the top of the Table Bed is in front of the Crossbar (Figure 16). REAR • Lower each Roller Hinge Pivot Pin into the A-Frame hinge plates one side at a time (Figure 20).
For All Models STEP 5 Assemble Main Shaft to Table Bed 3 FIGURE 20 4 5 6 7 8 9 • Your model’s Main Shaft may differ from what is shown in the figures, however the assembly instructions remain the same. H • Facing the front of the A-Frame, hold the Main Shaft in your left hand with the height markings facing up. Slide the end of the Main Shaft into the Main Shaft Housing (Figure 20) located at the base of the Table Bed.
For All Models STEP 6 Attach Angle Tether & Head Pillow Attach Angle Tether FIGURE 24 • The tether will come pre-assembled to the A-Frame. • Unfold the adjustable tether and clip it to the U-Bar on the underside of the Table Bed (Figure 24). • Slide the buckle to lengthen or shorten the strap depending on your desired maximum angle of inversion.
For All Models Misassembly Check ! WARNING If your Teeter Inversion Table looks like either of these images, your inversion table has been misassembled and is unfit for use. Improper assembly could result in serious injury or death! Image A Go back to Step 3 for instruction. Demonstrates that the Roller Hinges have been assembled upside down into the Table Bed and must be corrected. 12 Image B Go back to Step 4 for instruction.
For All Models Before Inverting Ensure Owner’s Manual is Attached FIGURE 26 The Owner’s Manual contains important information on how to use your Teeter Inversion Table, including how to personalize the user settings, properly secure and release the Ankle Lock System, and test and adjust the rotation control. • If not already attached, thread the provided metal chain through the pre-punched hole in the upper corner of the Owner’s Manual.
FULL 5 YEAR WARRANTY The Teeter warranty set forth below and on Teeter.com applies to the Inversion Table only. Accessories may come with their own terms. This warranty applies to US and Canadian customers only. For international customers, please consult your local distributor for warranty information which will vary depending on country.
Find These Great Products and More at teeter.com! T3 Massager P2 Back Stretcher Better Back Foam Rollers Better Back Neck Restore ™ ™ Countless options for self-massage, trigger point therapy, and myofascial release to resolve tension and pain gently and naturally. ™ Prepare the body for movement, accelerate recovery, minimize muscular imbalances, and improve overall flexibility with the Teeter collection of textured Foam Rollers.
