User guide

ManualsBrandsTeeJet ManualsComputers744A Sprayer Control

VOYAGER

570G

U S E R M A N U A L

744A Sprayer Control

Summary of content (14 pages)

PAGE 1
VOYAGER 570G 744A Sprayer Control ® U SS EE RR U M MA AN NU UA AL L
PAGE 2
744A Sprayer Control Table of Contents CHAPTER 1 - INTRODUCTION.....................................................................1 SYSTEM CONFIGURATIONS.............................................................................................................................1 KIT CONTENTS......................................................................................................................................................3 CONTROL HOUSING ASSEMBLY..........................................
PAGE 3
744A Sprayer Control ii www.teejet.
PAGE 4
744A Sprayer Control CHAPTER 1 - INTRODUCTION SYSTEM CONFIGURATIONS Figure 1-1: Solenoid Valves 744A Console Mounting Bracket 64-50023 • Manual spray controller in a compact package. • Liquid filled 100 PSI or 300 PSI pressure gauge.
PAGE 5
744A Sprayer Control Figure 1-2: Ball Valves Figure 1-3: Plumbing Diagram - Diaphragm Pump 744A Console Cable, Extension 10’ 45-10086 To 744A Controller Throttling Valve TeeJet Jet Agitatior TeeJet DC: XX/XX 45-10072 45-10086 DC: xx/xx 45-05385 DC: xx/xx Harness, 744 Console 12’ 45-10072 Cable, Power Fused 45-05385 Tank Shut Off Regulating Valve Diaphragm Pump TeeJet 45-10080 DC: xx/xx Harness, 744 Ball Valve 45-10080 Boom Valves 1-3 Line Strainer Boom 1 Gauge Tee Valve, Regulating 35-02115
PAGE 6
744A Sprayer Control KIT CONTENTS Unpack the installation kit and identify the required parts. Item Part Number Description Quantity 1 67-20004 Tee Fitting, Nylon (Black)..........................................................................................1 2 67-20003 Male Connector, Nylon.............................................................................................1 3 67-20002 Tubing Nut, Nylon..................................................................................
PAGE 7
44A Sprayer Control Item Part # Description 3 67-20002 Tubing Nut, Nylon 4 67-20005 Close Nipple, Nylon (Black) 5 65-50005 Tubing Insert, Brass 6 64-50023 Mounting Bracket, Nylon 7 60-10026 Lock Knob 8 60-50000 1/4” External Tooth Lock Washer 9 60-50003 1” Bolt, Steel, Zinc Plated 10 60-50001 Flat Washer, Steel, Zinc Plated 11 60-50009 Lock Washer, Steel, Zinc Plated 4 www.teejet.
PAGE 8
744A Sprayer Control Item Part # Description 12 350-0062 Hex Nut, Steel, Zinc Plated 13 67-20001 Male Coupling, Nylon 14 90-50141 Accessory Bag - Items 2, 3, 5, & 7-13 15 75-50033 Control Housing 100 psi Liquid 16 75-50035 Control Housing 300 psi Liquid 17 98-70025 744A Manual Illustration CONTROL HOUSING ASSEMBLY New consoles have boom switches, guage lamps/LEDs and boom LED soldered to the circuit board.
PAGE 9
744A Sprayer Control Item Part Number Description (continued) 8 32-50010 Toggle Switch 9 350-2610 Plastic Screw 10 64-50030 Foam Spacer 11 64-50025 Back Housing 12 64-50029 Elbow, Nylon (Black) 13 64-50032 Output Cable Shield, Neoprene 14 64-50026 Receptacle Fuse Shield, Neoprene 15 604-0014 Fuse, 15A Figure 1-6: Assembly 9 5 10 6 15 8 13 8 4 14 6 7 12 3 1 6 8 www.teejet.
PAGE 10
744A Sprayer Control CHAPTER 2 - INSTALLATION MOUNTING BRACKET 1. Make sure all switches on the 744A Sprayer Control are turned to the “Off” position. 2. Determine the best location for the 744A Sprayer Control in the vehicle cab according to the following guidelines: • pressure gauge should be readily visible • switches should be within easy reach • controller bracket should rest on a flat surface • 12 volt DC power source must be accessible (maximum draw 10 amps) 3.
PAGE 11
744A Sprayer Control Figure 2-2: Figure 2-2: T-Tap Connector Assembly To Terminal of 144 Directo Valve Step A Step B Step C Ball Valve Connector Input Power Cable The Input Power Cable consists of three wires. The red wire should be connected to a 12 Volt power supply within the cab of the vehicle (i.e., ignition switch). If the power source is located outside of the cab, the power cable should exit the cab through the same 1.0” (3.0 cm) diameter hole as the output control cable.
PAGE 12
744A Sprayer Control Pressure Gauge Tube Assembly 1. Determine the location at which the coupler is to be installed. Cut the tubing at that point. 2. Remove the tube nuts from the 3 couplers and slide the tubing through the nuts. The threaded portion of the nut should face their respective couplings. The tube should protrude approximately ½” beyond the nut. 3. One brass tube insert is provided. This must be used with the gauge coupling assembly. 4.
PAGE 13
744A Sprayer Control CHAPTER 3 - MAINTENANCE Routine Procedures Several routine procedures should be followed to help maintain the 744A Sprayer Control system. 1. Check all wires and connections for wear, damage, and frayed ends to prevent shorting out of the system. 2. Make sure that the mounting bracket for the 744A Sprayer Control is mounted securely. 3. All connections and terminals should be free of corrosion. 4.
PAGE 14
744A Sprayer Control U S E R M A N U A L TeeJet 744A manual Sprayer Control for use with Solenoid or Ball Valves • Manual spray controller in a compact package. • Liquid filled 100 PSI or 300 PSI pressure gauge. • Lighted pressure gauge for night use. • Heavy-duty switches with LED indicators. • Available in a variety of kit forms using solenoid or ball type control valves. • DirectoValve shutoff ball valves are ordered separately for 744A ball valve kits. • Kits include wiring harness.