WM5030-OD WiMAX Outdoor Modem Quick Installation Guide Version 1.3 TECOM CO.
WM5030-OD QIG TABLE OF CONTENTS 1. UNPACK THE OUTDOOR MODEM....................................................................................................................... 1 2. MAKING CONNECTIONS ........................................................................................................................................ 2 3. OMK.................................................................................................................................................................
WM5030-OD QIG 1. UNPACK THE OUTDOOR MODEM The following figure lists the items shipped with WM5030OD outdoor modem: 1. PoE Adapter: Qty 1 2. 1.5 M 8P4C gray Ethernet cable (between computer and PoE): Qty 1 3. 1 M 8P8C white Ethernet cable (between PoE and Modem) note : Qty 1 4. Quick Installation Guide: Qty 1 5. WM5030-OD outdoor modem: Qty 1 6. Mounting kit: Qty 1 7. RJ45 connector water sealing plug: Qty 1 8. CD-ROM: Qty 1 9. 1.5M Power Cable for PoE Adapter: Qty 1 10.
WM5030-OD QIG 2. MAKING CONNECTIONS In order to configure WM5030 outdoor modem, please take the following steps: 1. Connect the white Ethernet cable between the RJ-45 connector located at the bottom of the outdoor modem and the “Data & Power Out” port of PoE adapter. 2. Connect the gray Ethernet cable between the “data in” port of the PoE adapter and your personal computer. 3. Plug the PoE adapter power cable to power outlet 4.
WM5030-OD QIG 3. OMK OMK (Outdoor modem Monitoring Kit) is a convenient tool for technician during installation, testing and maintenance for WM5030-OD. It is designed for easy carrying and an excellent tool to display radio quality for technician to adjust orientation and tilt of WM5030-OD for best reception from WiMAX base station. OMK features include: z CINR signal quality z Link status z Power indicator z Reset to factory default Figure 3.
WM5030-OD QIG Table 1: Definitions of OMK LED Color Function CINR 31 ≥ 29 > 27 > 24 > 20 > 15 > 10 > CINR Signal > CINR ≥ CINR ≥ CINR ≥ CINR ≥ CINR ≥ CINR ≥ CINR ≥ < 5dBm Indicator 31dBm 29dBm 27dBm 24dBm 20dBm 15dBm 10dBm 5dBm WiMAX Saturate Green Red RSSI > -20dBm: ON (saturate) LED WiMAX Green Operational: ON Not in operation: OFF Link LED Power Green Power-on: ON, Power-off: OFF LED Reset Push and hold for 20 seconds will reset WM5030-OD to factory default Butt
WM5030-OD QIG 4. NETWORK CONFIGURATION 4.1 Setup your computer to configure WM5030-OD Step 1: Complete prior section 2 to connect your computer and WM5030OD. Step 2: Make sure the power indicator on Modem is on. Step 3: Find your “Network Connections” setting in “Control Panel” Step 4: In your “Network Connections”, right click “Local Area Connection”, and then select “Properties”. (Ref. Figure 4) Figure 4.
WM5030-OD QIG Figure 5. TCP/IP Step 6: Enter 192.168.111.100 into IP address and 255.255.255.0 into Subnet mask, and click “OK”. (Ref. Figure 6) Figure 6. IP Configuration Step 7: Enter the IP address (default is 192.168.111.113) of WiMAX modem into Web Browser. A dialog Box will pop out to request for user login information (Ref. Figure 7). Please enter management username/password into the required fields, then click “Apply” to continue.
WM5030-OD QIG 4.2 Making Connection to WiMAX Network Step 1: Press “Disconnect” button. If user is already connected to WiMAX network, then new channel cannot be added to the scan list (Ref. Figure 8) Figure 8. Disconnect before Scanning Step 2: Type in the central frequency of the WiMAX operator, and select the correct bandwidth to add new frequency to the scan list (Ref. Figure 9). Figure 9. Add Operator Central Frequency to Scan List Note: A channel cannot be added when WiMAX modem is scanning.
WM5030-OD QIG Step 3. To use the authentication feature, user must provide security settings. Please first select “Authentication” at the right of the modem home page. If operator requires TLS setting, please follow steps 4-A. If operator requires TTLS, then please follow step 4-B (Ref. Figure 10). Figure 10. Choose TLS or TTLS for Authentication Note: The factory default Authentication setting is “None”.
WM5030-OD QIG Step 4-B: Please locate the proper CA Certificate file, User Certificate file and Decryption Key file to upload to WM5030-OD. Please contact your WiMAX operator for Password of Decryption Key file. Please select the desired Inner EAP category and enter Identity, Inner Identity and Password, then click “Apply” to configure. (Ref. Figure 12) Figure 12. TTLS Configuration Note: The above figures are just for example.
WM5030-OD QIG Step 6: Now, please change the network setting of your computer in Internet Protocol (TCP/IP) properties, select “Obtain an IP address automatically” and select “Obtain DNS server address automatically”. Figure 14. Configure Your Computer TCP/IP Setting Step 7: Open web browser such as Internet Explorer (IE) to access Internet to check whether you have successfully connected to the Internet.
