md Table Of Contents i. Key layout of the handset Crees asseverate 2. Indicators 2.1. Indicators on the Base unit . 2.2. Indicators on the Handset Charger unit . . 3. Installation ce 3.1 Base unit DIP switch setting 3.2 Summary of the Programming and Function Codes . 3.3 System Security Code programming . 3.4 Handset ID setting eee .. 3.5 Standby Mode . 3.6 CO Line Ring Programming Ringer Type programming . 3.8 Handset Reset programming . . 4. Making outside line calls . S. Answering calls . 6.
wr ow lean After power on 10 seconds still without programmed, Base unit in Que-Of-Service mode ~ . Wink ~ 0.125sec on, 1.875sec off, repeatedly Base unit but can not find an idle channel, Base unit in Error mode .Flick 0.125sec off, 0.25sec on, 0.125sec off, 0.25sec on, 0.12Ssec « Lit off, 1.1255 on, repeatedly : Both the RF link are busy, Base unit in Busy mode — Base unit with 5.5.C. programmed, Base unit in Service mode 2.2. Indicators on the Handset Charger unit.
P— fend eo ean pe— 3.1.3. Reset the Base Unit You may 'RESET' the base unit by setting the dip switch, and clear ~. all the programming data back to the default setting. Set the DIP switch to the special patent 1234 ¥ DIP 1,2,3 : set to off. aR DIP 4 : set to on. Power on the base unit again, and set the base unit to a proper ID number as paragraph 3.1.1. 3.2. Summary of the Programming and Function Codes 3.2.1. Programming Codes ’ There are some programming parameters on the handset, and here is the list.
FUN } 2 PAUSE code, to insert a delay during digits FUN CONFERENCE code, to bridge 3-way conference call FUN DND code, to activate Do Not Disturb feature 3.3 System Security Code programming The (System Security Code) prevents your cordless system from or being used by other cordless telephone user. 3.3.1. Programming the System Security Code on the Handset. . Standby Press [ MEMO ] « Press twice for 3.5.C. programming mode code Enter [ ] 6 digits for new cede, say 775141.
prey 3.8 Handset Reset programming You may RESET the handset and clear all the programmed data, all + the parameters will back to the default values. ~ SPD memory : empty Handset ring assign : all 4 line will ring Ringer volume -: Mid level Ring Type : type 1 KF 5.8.C.
foe peed 6. When conversation is over . Press the [ CLR ] key, to resale the call Last number redial 6.1. Making An Outgoing Call by LNR Standby Press an available [ COx }, where xz = 1/2/3/4 Press the [ LNR ] to redial the last dialed number 6.2. Making An Outgoing Call by LNR with Lipreading . Standby Press the [ LNR | key After Last dialing number reviewed, and you want to dial the number Press an available [ Cox ], where x = 1/2/3/4, handset will dial out the number as display on the LCD 7.
Answering an Incoming Intercom Call Handset rings Press | any one of the digit ] key, or you may press the ( ICM | to pick up the ringing intercom call Re lase the Intercom Call When conversation is over Press ([ CLR ] key, to resale the call Dial Intercom Call and Single Page Call Interchanging : Reserve for future developing. Voice Page All Stations : Reserve for-future developing. Conference Call You may make a three-way conference call. 1.
Fed ¥ 15. Transferring a Call : 15.1. Transferring a Call . On line Press the { HOLD | key ‘Before the 10 seconds time-out, enter the transfer station number At the transferred handset will heard a transfer ring, and 15.2. Transferring recall . If the transferred call didn't answer over one minute, the system will recall to all the handsets to remind there is a line being held too long. + Press [ any one of the digit | key, or you may pass the recalling [ COx ] to pick up the CO ringing line 16.
Press the, [ MEMO ] key again, to store the number into memory A confirmation beep will be heard 6.3. Erasing the speed dial memory Handset standby mode Press [ MEMO | key Enter the memory location number or use the key to scroll the ‘memory location « Press the [ FUN ] key Press the [ CLR j kay, to erase the memory Press the [ MEMO } key again, to erase the memory + A confirmation beep will be heard 16.4. Using thé speed dialing .
— p— poe 17. 18. 2. Programming the FLASH time You may program the FLASH time duration as your service need, from 100ms up. .to sec. Default is 0.6 second. . Standby « Press [ MEMO ] . Press the [ * |] key, to enter the handset parameters programming Press the to select the FLASH Time programming mode . Enter 1 digit [ 7 ] for new FLASH time selection, 1 for 0.1lsec, 2 for 0.2sec, 0 for l.0sec, * for l. S5sec, # for 2.0sec.
Ld —— er faced Evian —— p—— + Standby Press ([ FUN |] key Press {[ DND key, to activate DND Press [ FUN | key Press [ DND key again, to disable DND 21. MUTE function The Mute feature turns off the microphone so the person at the other phone cannot hear you. The Mute feature automatically cancels when you hang up, change lines. On line Press the [ MUTE } key for privacy + Press the [ MUTE ] key again, to resume your conversation 22.
Np peer If you are on a call when battery low, end the conversation as soon as possible. Otherwise, you may lose the call. 25. Complete with Headset The Headset frees your hands so you can keep working. Plug the headset into the headset jack, you're all set. 26. Ringer Volume programming You may adjust the ringer level of the handset to one of the three levels (Low/Mid/Hi), each time you change it you will hear the ringer level setting for your reference. Default is the level Mid. 26.1.
