IG7500 Administration Manual Copyright © 2012 TECOM Co., Ltd. All Rights Reserved.
IG7500 Administration Manual Environment The equipment you have purchased must not be disposed of with household waste. You should return these to your distributor if they are to replace or dispose of them in an approved recycling centre. FCC Statement This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause interference to radio communications.
IG7500 Administration Manual WARNING! ! 1. Read these installation instructions carefully before connecting the equipment to its power adapter. 2. To reduce the risk of electric shock, do not remove the cover from the equipment or attempt to dismantle it. Opening or removing covers may expose you to dangerous voltage levels. Equally, incorrect reassembly could cause electric shock on re-use of the appliance. 3. Do not expose the equipment to fire, direct sunlight or excessive heat. 4.
IG7500 Administration Manual Table Of Contents 1. 2. 3. 4. Introduction .................................................................................................................................... 6 Getting to Know the IG7500 ........................................................................................................... 7 2.1 Front Panel................................................................................................................................. 7 2.2 Rear Panel....
IG7500 Administration Manual 4.8 Diagnostics................................................................................................................................34 4.9 Logout ......................................................................................................................................34 Appendix 1: Product Summary .............................................................................................................
IG7500 Administration Manual 1. Introduction The IG7500 Gateway supports a FXS port and a FXO port, both have a separate SIP account assigned to register to remote SIP Sever. The IG7500 also support IP networking systems. The IG7500 design is designed for hosted IP providers that want to provide fax services, support PSTN failover, and managed WLAN for the customers.
IG7500 Administration Manual 2. Getting to Know the IG7500 2.1 Front Panel The front panel contains several LEDs that indicate the status of the IG7500. Figure 2-1.
IG7500 Administration Manual 2.2 Rear Panel The rear panel contains the ports for the IG7500's data and power connections. Figure 2-2. Rear Panel of IG7500 Label Line TEL WAN LAN USB RST DC-IN USB Power Function RJ-11 connector: Connects the device to your PSTN lines. RJ-11 connector: Connects the device to your analog phone. RJ-45 connector: Connects the device to your cable modem, or to your ADSL Modem. It’ s to connect to the remote network.
IG7500 Administration Manual 3. General Features (Some enhanced features as described will be added soon.) 3.1. FXS Application It needs to program the FXS IP account in Web (Voice – Extension), and get the registration well first. 3.1.1 Make an outbound call Dial a phone number. When dialing the pound (#” ) key or waiting Interdigit Timeout (programmed in “ Web – Voice – Transmission; Default: 5 seconds), the FXS IP call is formed.
IG7500 Administration Manual number (programmed in “ Web – Voice – Extension à FXO) through the IP line immediately. If the FXO IP account is at Fail state, and the FXS is at idle state, the PSTN line will ring the FXS phone. 3.2.3 Call Abandon For PSTN call, IG7500 provides the facility to monitor the call status. If the remote party hangs up, the ongoing call will be terminated. The PSTN line monitor is accomplished through monitoring the loop-break signal, polarity reversal or busy tone.
IG7500 Administration Manual IG7500 also provide Caller ID Generation to the Caller ID equipped Single Line Telephone. 3.4.2 PSTN Backup In case of power failure, IG7500 automatically switches the first PSTN line to the Single-line analog phone.
IG7500 Administration Manual 4. Configuration (Some enhanced configuration items as described will be added soon.) 4.1 Setup l Connect the IG7500 to PC. l The default LAN IP of the IG7500 is 192.168.1.1. l The default WAN IP of the IG7500 depends on upper router’s DHCP server. l For web login, the default user name is “admin1234”, the default password is “123456”. l For telnet login, the name/password is the same as web login. 4.
IG7500 Administration Manual l l l l l l Wireless Mobile Network Voice Management Diagnostics Logout Figure 4-2.
IG7500 Administration Manual 4.3 Device Info This information reflects the current Status of IG7500 connection. It includes the following topics: l Summary l Statistics l Route l ARP l DHCP 4.3.1 Summary In the page (Figure 4-2) you can get the information reflects the current software version and connection status. It includes Device Info, Network Info and Date/Time.
IG7500 Administration Manual Figure 4-4. Device Info – Statistics – WAN 4.3.3 Route In this page you can get the IP route information of the device. (Figure 4-5) Figure 4-5. Device Info – Route 4.3.4 ARP This page shows an ARP table which maps IP network addresses to hardware addresses used by data link level protocol. (Figure 4-6) Figure 4-6.
IG7500 Administration Manual 4.3.5 DHCP This page shows a DHCP Leases table which shows the all used IP addresses under IG7500’ s DHCP Server. (Figure 4 -7) Figure 4-7.
IG7500 Administration Manual 4.4 Advanced Setup Advanced Setup allows system administrator to configure the following topics: l WAN l LAN l NAT - Virtual Servers - DMZ Host l Quality of Service - DSCP Marking - Bandwidth Control l Dynamic DNS l File Server l Print Server 4.4.1 LAN It allows you to set LAN IP and Subnet Mask for LAN interface. A DSP IP address can be configured for FXO/FXS application. You can also enable or disable DHCP Server and configure related settings.
IG7500 Administration Manual Figure 4-9. Advanced – WAN (Static IP Mode) The Dynamic Host Configuration Protocol (DHCP) is an Internet protocol for automating the configuration of computers that use TCP/IP. DHCP can be used to automatically assign IP addresses, to deliver TCP/IP stack configuration parameters such as the subnet mask and default router, and to provide other configuration information. This page shows the setting of WAN interface which is DHCP mode (Figure 4-10). Figure 4-10.
IG7500 Administration Manual Figure 4-11. Advanced – NAT – Virtual Servers 4.4.3.2 DMZ Host IG7500 will forward IP packets that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer. Enter the computer's IP address and click "Save Settings" to activate the DMZ host. Clear the IP address field and click "Save Settings" to deactivate the DMZ host. (Figure 4 -12) Figure 4-12. Advanced – NAT – DMZ 4.4.
IG7500 Administration Manual Figure 4-13. Advanced – Quality of Service – DSCP Marking 4.4.4.2 Bandwidth Control Bandwidth Control allows you to control WAN port's upstream bandwidth according to your settings, and it can ensure the highest priority IP packet traffic throughput. By default, all voice packets ha ve been queued in the highest IP packets, and the others have been queued in the normal IP packets if they have not been set in the traffic class rule. Figure 4-14.
IG7500 Administration Manual Figure 4-15. Advanced – Dynamic DNS Now IG7500 support for two DDNS provider, DynDNS.org and TZO. Specify the register hostname and choose the related interface. Fill in the username/password or email/key and click “Apply/Save”. IG7500 will update the current IP with DDNS provider when click “Apply/Save ” or system reboot successfully. IG7500 will also update the current IP automatically with DDNS provider in the programmed Update Cycle.
IG7500 Administration Manual Figure 4-17.
IG7500 Administration Manual 4.5 Wireless Use the Wireless screen to configure the IG7500 for wireless access. It is separated into 7 parts: l Basic - Primary l Security l Advanced l Station Info l Power Saving The configurable items for each part would be described in the following. 4.5.1 Basic 4.5.1.1 Primary This page allows you to configure the basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, and hide the network from active scans .
IG7500 Administration Manual Figure 4-19. Wireless – Security 4.5.3 Advanced It allows you to configure advanced features of the wireless LAN interface. You can select a particular channel on which to operate, force the transmission rate to a particular speed, set the fragmentation threshold, set the RTS threshold, set the wakeup interval for clients in power-save mode, set the beacon interval for the access point, set XPress mode and set whether short or long preambles are used.
IG7500 Administration Manual Figure 4-20.
IG7500 Administration Manual 4.6 Voice Use the Voice screen to configure the IG7500’s voice related parameters. It allows system administrator to configure the following topics: l Extension l Transmission The configurable items for each part would be described in the following. 4.6.1 Extension Use the Extension screen to configure IG7500’ s FXS/FXO SIP registration account to remote Server. (Figure 4-21) Figure 4-21. Voice –Extension -1 Figure 4-22.
IG7500 Administration Manual FXO/FXS Settings: Phone Number: It’s the assigned phone number from uplink server. Auth ID: The Account ID of registration to uplink server. It’ s used for Digest Authentication. Auth Password: The Password of registration to uplink server. It’ s used for Digest Authentication. SIP Proxy: The position of uplink SIP proxy server. IP address and domain name are all supported. SIP Proxy Port: The SIP signal port of uplink registrar server.
IG7500 Administration Manual Figure 4-23. Voice – System – Transmission – 1 Audio: It is used to set many Audio-related options. It will be applied to the all FXS and PSTN lines. Country: It may be used to determine not only the Caller ID detection/transmission method but also ring/tone cadence/frequency. RTP Packet Size: 10/20/30/40/50/60 ms. Codec G.711 u-law, G.711 a-law, G.726-16, G.726-24, G.726-32, G.726-40: IG7500 supports different audio priority.
IG7500 Administration Manual Figure 4-24. Voice – System – Transmission – 2 FXO: It is used to set many central office line options. Loop Break Detection Time: For every PSTN/FXO call, system provides the facility to monitor the call status. If the remote party hangs up, the ongoing call must be terminated. The PSTN line monitor is done by the loop-break signal or busy tone. The value range is: Disable/100/200/…/1000 ms.
IG7500 Administration Manual 4.7 Management The system administrator can do the following functions to manage the configurations, events, and software update of the IG7500. l Settings - Backup - Update - Restore Default l Access Control - Services - Password l System Log l Time Settings l Update Software l Reboot 4.7.1 Settings The settings area allows the administrator to create a backup, update the system, and restore the system to factory default. 4.7.1.
IG7500 Administration Manual 4.7.1.3 Restore Default Click “ Restore Default Settings” to restore the factory default settings. This would be helpful when the settings mass up. After IG7500 returns to factory default settings, the wizard setup is invoked automatically when the administrator accesses to IG7500’s web server. (Figure 4-27) Figure 4-27. Management – Settings – Restore Default 4.7.
IG7500 Administration Manual Figure 4-29. Management – Access Control – Password 4.7.3 System Log This allows system administrator to view the system log. (Figure 4-30) When you configure the system log options, The log messages can be saved in the internal memory filesystem. The log messages can sent to the specified UDP port of the specified log server also. Click “Apply/Save” button that you can save the new configuration. Figure 4-30. Management – System Log 4.7.
IG7500 Administration Manual Figure 4-31. Management – Time Setting – Internet Time – Automatically 4.7.5 Update Software The new released software could be upgraded from the Local PC side or remotely. Click the “ Browse” to locate the new software image file in the PC. Then, click “ Update Software” to process the software update. NOTE: The upgrade process takes about 5 minutes to complete, and your IG7500 will reboot. (Figure 4-32) Figure 4-32. Management – Update Software 4.7.6 Reboot Figure 4-33.
IG7500 Administration Manual 4.8 Diagnostics This page provides the following information to users: (錯誤! 找不到參照來源。) l The network connection information on the net. l The status of IG7500's PSTN Line. l The status of IG7500’s FXS.
IG7500 Administration Manual Appendix 1: Product Summary Hardware n n n n n n n n n 1 FXO port (PSTN) 1 FXS Port (fax) 1 10/100/1000 Ethernet WAN port 4 10/100 Ethernet LAN ports 802.11n access point 3 USB 2.0 host ports WPS button Power plug Reset button Voice Features n SIP : Compliant with IETF RFC3261 standards n SDP : Compliant with IETF RFC2327 standards n Codec : G.711u, G.711a, G726-16, G726-24, G726-32 and G.726-40 (G.729a optional) n T.168 echo cancellation, adaptive jitter buffer & T.
IG7500 Administration Manual n Priority queues for upstream traffic based on ToS field. n Bandwidth Control 3G n 3G HSDPA dongles for WAN backup and 3G interface n Bandrich, Huawei, ZTE and D-Link dongles will be supported by default, other dongles will be supported upon request VoIP Protocols n n n n n n SIP (RFC 3261) SDP(RFC2327, RFC3264) Real Time Protocol (RTP ; RFC 1889) MD5 (RFC3261 HTTP) digest authentication G.168 Echo Cancellation Voice Codec: G.711u, G.711a, G726-16, G726-24, G726-32 and G.
IG7500 Administration Manual n Syslog n Device Diagnostic, Enable remote test following : Test the connection to your local network, The connection to your Internet service provider, The status of PSTN Line, The status of FXS Power Requirement n Input : Voltage Range 90~264 VAC n Output : 12VDC / 1 .
