2/1-port FXS ATA WiFi-Router Quick User Guide 2/1-port FXS ATA WiFi-Router Quick User Guide Preliminary Copyright © All Reserved, 2007 QUG-TSIP-2512GR-R3-960604 Copyright © 2007, M/C:TSIP-2512GR-R3 Page 0
/1-port FXS ATA WiFi-Router Quick User Guide FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
2/1-port FXS ATA WiFi-Router Quick User Guide ! WARNING! 1. Read these installation instructions carefully before connecting the 2/1-port FXS ATA WiFi-Router to its power source. 2. To reduce the risk of electric shock, do not remove the cover from the 2/1-port FXS ATA WiFi-Router or attempt to dismantle it. Opening or removing covers may expose you to dangerous voltage levels. Equally, incorrect reassembly could cause electric shock on re-use of the appliance. 3.
2/1-port FXS ATA WiFi-Router Quick User Guide 1 Introduction The 2/1-port FXS ATA WiFi-Router is a SIP- based high performance WiFi IP gateway with embedded router. It is ideal for residential/SOHO or even SME VoIP communications. It can support 2 FXS ports for phone or FAX. Furthermore, this product is configurable for matching with different telephones, facsimiles, voice mail systems, IVR system and different country networks over the world by software settings.
2/1-port FXS ATA WiFi-Router Quick User Guide 3 About The WiFi ATA LED Indications: There are 9 LED indicators in the router to show the Power (PWR), LAN Port4 (LAN4), LAN Port3 (LAN3), LAN Port2 (LAN2), LAN Port1 (LAN1), WAN Port (WAN), Telephone port1 (FXS1), Telephone port2 (FXS2) status. DC IN: Power input jack 2.5mm diameter, external wall-mount 13V/800mA power adaptor. Reset (RST) button: For factory default setting. FXS port: There is one or two two RJ-11 Type analog telephone jack interface.
2/1-port FXS ATA WiFi-Router Quick User Guide 4 Installation Figure 4.
2/1-port FXS ATA WiFi-Router Quick User Guide Figure 4.2 The Connection of 2/1-port FXS ATA WiFi-Router at Home(2) Figure 4.
2/1-port FXS ATA WiFi-Router Quick User Guide Please refer to the figure Fig.4.1 ~ 4.3 above. Then please connect one analogue phones to FXS1 port. And then use an Ethernet cable (CAT-5) to connect the WAN port to the broadband network end (e.g. an ADSL modem, a cable modem, or a router etc). Step 2: Connect power With the power adaptor in the product package, please plug its power cord to the rear panel of 2/1-port FXS ATA WiFi-Router. Then plug the power plug to the wall outlet.
2/1-port FXS ATA WiFi-Router Quick User Guide - Please input the username: “guest” and password: “guest”. Then click “Login” button. - You also can login as an administrator by input the username: “admin” and password: “admin”. Then click “Login” button. - After get in the web page, it is highly recommended to change Username and Password. You can change your username (login) name and password in System management-> User Management page. After you finish the Settings, please click the Save button.
2/1-port FXS ATA WiFi-Router Quick User Guide - After configuration, please “Save” to update the settings in the router. - You can click “Factory Default” button to restore to factory default setting in System management->Reset Setting page.
2/1-port FXS ATA WiFi-Router Quick User Guide Before you place a call, you must setup SIP configuration in Telephony Setting page. Port1 is for FXS1, port2 is for FXS2. - You must give number, Login ID, Password - Check Proxy Enable box to enable SIP proxy function and then give proxy address in Proxy Addr field. - Check Outbound Proxy Enable box to enable outbound proxy function and then give outbound proxy address in Outbound Proxy Addr field.
2/1-port FXS ATA WiFi-Router Quick User Guide - Step 1. Hook flash the phone, then you can hear the dial tone, dial the numbers you want to call and press “#” to call out. - Step 2. If you hear busy tone after hooking flash the phone, it means you can’t dial a second call now. You just need to hook down the phone. - Step 3. If you hear ring tone after hooking down the phone, pick up it to release a call, or you can ignore it. It will automatically stop when the remote hang up this call.
