OWNER’S MANUAL If you do not have prior experience with a metal detector, we strongly recommend that you: 1) Adjust the Sensitivity to a low setting in the event of false signals. Always begin use at a reduced sensitivity level; increase sensitivity only after you have become familiar with the detector. 2) Do not use indoors. This detector is for outdoor use only. Many household appliances emit electromagnetic energy, which can interfere with the detector.
TABLE OF CONTENTS TROUBLE SHOOTING TROUBLE SHOOTING GUIDE Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Quick-Start Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HEADPHONE JACK TERMINOLOGY The detector has a 1/8” & 1/4” headphone jack on the left side of the housing. The following terms are used throughout the manual, and are standard terminology among detectorists. Optional Headphones come standard with a 1/8” stereo plug (the 1/4” adapter is not required). ELIMINATION When the headphone jack is connected, speaker audio is disabled. Using a detector with headphones facilitates detection of the weakest signals and also extends the battery life.
ASSEMBLY IN THE FIELD TECHNIQUES (continued) Hand-grip Assembly is easy and requires no tools. 1 ● Loosen both Locking Collars by rotating 100% counterclockwise. 2 ● Insert the Upper Stem into the S-Rod and click Silver Button into hole. 3 ● Position the Lower Stem with the Silver Strap Button toward the back. Using the Bolt and Knurled Knob, attach the Search Coil to the Lower Stem.
IN THE FIELD TECHNIQUES (continued) Swing the search coil slowly, overlapping each sweep as you move forward. It is important to sweep the coil at a consistent speed over the ground as you search. After identifying a target, your sweep technique can help in identifying both the location and the nature of the target. If you encounter a weak signal, try moving the coil in short, rapid sweeps over the target zone; such a short rapid sweep may provide a more consistent target identification.
BATTERIES IN THE FIELD TECHNIQUES The detector requires a single 9-volt ALKALINE battery (battery not included). Do not use ordinary zinc carbon batteries. PINPOINTING COIL MOVEMENT Accurate pinpointing takes practice and is best accomplished by “Xing” the target area. When swinging the coil, be careful to keep it level with the ground about one inch from the surface. Never swing the coil like a pendulum. Rechargeable batteries can also be used.
DEPTH AND TARGET DISPLAY QUICK-START DEMONSTRATION READING THE DISPLAY I. Supplies Needed • a Nail • a Zinc Penny (dated after 1982) • a Nickel • a Quarter II. Position the Detector a. Place the detector on a table, with the search coil hanging over the edge. Or better, have a friend hold the detector, with the search coil off the ground. b. Keep the search coil away from walls, floors, and metal objects. c. Remove watches, rings, and jewelry. d.
THE BASICS OF METAL DETECTING TARGET IDENTIFICATION A hobby metal detector is intended for locating buried metal objects. When searching for metals, underground or on the surface, you have the following challenges and objectives: Targets are identified both audibly and visually as follows: 1. Different pitch tones for different types of metals 2. An illuminated icon within the target category best describing it. 1. Ignoring signals caused by ground minerals. 2.
OPERATION and CONTROLS cont. THE BASICS continued NOTCH continued 4. Size and Depth of Buried Objects For example, the following settings tell us that: • The nickel, dime, quarter, and 50¢+ categories will be detected. • All other categories of targets (iron, foil, alum, and zinc) will not be detected. The relative depth of an object is displayed at the left of the display as a 1 digit number, 0 to 9 inches. The size of an object can be determined using sweep techniques described later in the manual.
OPERATION and CONTROLS OPERATION and CONTROLS POWERING UP MENU SELECTIONS Press • The detector always starts up with the DISCRIMINATION feature active. Motion is required to detect metal. • Sensitivity is at 70% of maximum • All target categories are illuminated, meaning that all metal objects will be detected. HOW TO WORK THE CONTROLS 1. DISC Use and to increase or decrease DISCRIMINATION level. Each time you press , a target category is eliminated from detection.
OPERATION and CONTROLS OPERATION and CONTROLS POWERING UP MENU SELECTIONS Press • The detector always starts up with the DISCRIMINATION feature active. Motion is required to detect metal. • Sensitivity is at 70% of maximum • All target categories are illuminated, meaning that all metal objects will be detected. HOW TO WORK THE CONTROLS 1. DISC Use and to increase or decrease DISCRIMINATION level. Each time you press , a target category is eliminated from detection.
OPERATION and CONTROLS cont. THE BASICS continued NOTCH continued 4. Size and Depth of Buried Objects For example, the following settings tell us that: • The nickel, dime, quarter, and 50¢+ categories will be detected. • All other categories of targets (iron, foil, alum, and zinc) will not be detected. The relative depth of an object is displayed at the left of the display as a 1 digit number, 0 to 9 inches. The size of an object can be determined using sweep techniques described later in the manual.
THE BASICS OF METAL DETECTING TARGET IDENTIFICATION A hobby metal detector is intended for locating buried metal objects. When searching for metals, underground or on the surface, you have the following challenges and objectives: Targets are identified both audibly and visually as follows: 1. Different pitch tones for different types of metals 2. An illuminated icon within the target category best describing it. 1. Ignoring signals caused by ground minerals. 2.
DEPTH AND TARGET DISPLAY QUICK-START DEMONSTRATION READING THE DISPLAY I. Supplies Needed • a Nail • a Zinc Penny (dated after 1982) • a Nickel • a Quarter II. Position the Detector a. Place the detector on a table, with the search coil hanging over the edge. Or better, have a friend hold the detector, with the search coil off the ground. b. Keep the search coil away from walls, floors, and metal objects. c. Remove watches, rings, and jewelry. d.
BATTERIES IN THE FIELD TECHNIQUES The detector requires a single 9-volt ALKALINE battery (battery not included). Do not use ordinary zinc carbon batteries. PINPOINTING COIL MOVEMENT Accurate pinpointing takes practice and is best accomplished by “Xing” the target area. When swinging the coil, be careful to keep it level with the ground about one inch from the surface. Never swing the coil like a pendulum. Rechargeable batteries can also be used.
IN THE FIELD TECHNIQUES (continued) Swing the search coil slowly, overlapping each sweep as you move forward. It is important to sweep the coil at a consistent speed over the ground as you search. After identifying a target, your sweep technique can help in identifying both the location and the nature of the target. If you encounter a weak signal, try moving the coil in short, rapid sweeps over the target zone; such a short rapid sweep may provide a more consistent target identification.
ASSEMBLY IN THE FIELD TECHNIQUES (continued) Hand-grip Assembly is easy and requires no tools. 1 ● Loosen Locking Collar by rotating 100% counterclockwise. 2 ● Insert the Lower Stem into the S-Rod and click silver button into hole. Press the silver button on the upper end of the lower sem Velcro Strap & slide the lower stem into the S-rod. 3 ● Position the lower stem with the silver button toward the back. Using the bolt and knurled knob, attach the search coil to the lower stem.
HEADPHONE JACK TERMINOLOGY The detector has a 1/8” & 1/4” headphone jack on the left side of the housing. The following terms are used throughout the manual, and are standard terminology among detectorists. Optional Headphones come standard with a 1/8” stereo plug (the 1/4” adapter is not required). ELIMINATION When the headphone jack is connected, speaker audio is disabled. Using a detector with headphones facilitates detection of the weakest signals and also extends the battery life.
TABLE OF CONTENTS TROUBLE SHOOTING TROUBLE SHOOTING GUIDE Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Quick-Start Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TREASURE HUNTER’S CODE OF ETHICS: • Always check Federal, State, County and local laws before searching. • Respect private property and do not enter private property without the owner’s permission. • Take care to refill all holes and try not to leave any damage. • Remove and dispose of any and all trash and litter found. • Appreciate and protect our inheritance of natural resources, wildlife and private property.
