BROADBAND INTERNET ROUTER – USER’S MANUAL Version 1.
BROADBAND INTERNET ROUTER – USER’S MANUAL 10/100M Broadband Router GETTING TO KNOW 2 3 4 1 5 6 7 - Page 2 of 13 -
BROADBAND INTERNET ROUTER – USER’S MANUAL LED Indicator S/N Indicator Function 1 Power LED (Green) LED lights up steadily indicate that the power is applied to the router. 2 LAN 100Mb LED (Green) LED lights up steadily indicate that the respective LAN connection is at 100Mbps. LED lights off indicate that the respective LAN connection is at 10Mbps.
BROADBAND INTERNET ROUTER – USER’S MANUAL C. Reset Button While you forget the password to login the utility or want to re-configure it, press the button to restore the factory default configuration. Press the button during 1~5seconds, system will just restart. Press the button more than 5 seconds, system will restore default config (default IP is 192.168.1.1) D. Hardware ♦ 4 LAN Ports For linking computers or other Ethernet devices, e.g.
BROADBAND INTERNET ROUTER – USER’S MANUAL Utility Setup 1. Before Setup… Have the following information ready For ADSL service with PPPoE, obtain the following information from your ISP: a. The user login name b. The login password c. Service name (some ISP may not require you to use this) If you have a fixed public IP address, obtain the following information from your ISP: a. The assigned Gateway IP address b. Domain Name Server’s IP address c. Subnet Mask Release/Renew IP Address of the PC a.
BROADBAND INTERNET ROUTER – USER’S MANUAL 3) You will enter the Utility homepage 2.
BROADBAND INTERNET ROUTER – USER’S MANUAL User could set the router IP and DHCP range. DHCP function must be enabled if user need Auto-IP assign by router.(recommend) User can set advanced DHCP options, can check the IP list information and lease time as below Click ‘DHCP server reservation’, the reserved IP list will be showed, and also can set reserved IP by user. 3.
BROADBAND INTERNET ROUTER – USER’S MANUAL Different Wan connect type could be selected by different web page. 1) PPP over Ethernet a) For ADSL user, please select PPP over Ethernet, and fill in the user name , password. Can set the connection type as ‘ On demand’ or ‘Always On’, and also the Idle time or reconnect time. b) For some ISP need MAC as the user identification, please clone your network MAC to the router, just click the ‘ MAC clone ’.
BROADBAND INTERNET ROUTER – USER’S MANUAL 4. NAT(network address translation) function Usually all PCs connected to the router are protected from Internet intruders by a built-in firewall. For some kinds of Internet applications, for example, Internet interactive games, video-conferencing, VPN (Virtual Private Network), or as an e-mail server etc., computers must be exposed to the Internet. The DMZ Host feature allows 15 local users to be exposed to the Internet.
BROADBAND INTERNET ROUTER – USER’S MANUAL 5. Routing If your Cable/DSL Router is connected to more than one network, you may have to set up a static route between the two networks. A static route is a predetermined pathway that network data packets must travel to reach a specific host or network. Click ‘Static Routing table’ can set routing function 6. LAN filter This feature allows you to block/enable some LAN Computers access to the Internet.
BROADBAND INTERNET ROUTER – USER’S MANUAL - Page 11 of 13 -
BROADBAND INTERNET ROUTER – USER’S MANUAL 7. Wan filter This feature allow you to access or block to some internet domain 8. System tools User can setup some feature according below list 1. Router identity: user can set router name, contact and router location. 2. Set router’s clock: user can set router time or get from time server 3. Firmware upgrade: user can upgrade software if needed 4. Save or Reset: a. User must Save the config after any changing b.
BROADBAND INTERNET ROUTER – USER’S MANUAL 9. System Information This page show all the current information of router.
