CAUTION—ELECTRIC TOY: Not recommended for children under 8 years of age. As with all electric products, precautions should be observed during handling and use to prevent electric shock.
This device complies with the part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
YOUR RUBIK’S ® TOUCHCUBE™ You hold in your hands the world’s first completely electronic, solvable Rubik’s® Cube. Each vibrantly lit square contains cutting edge, easy to use touch sensor technology. Swipe your finger across the squares to effortlessly slide the lights, mimicking every move of the original puzzle. If you’re ever stuck, the TouchCube can give you a hint or solve it step by step right before your eyes.
TOUCHCUBE CONTROLS Power – Press and hold for 1.5 seconds to activate. Scramble – Double tap to begin Hint Power Mode – page 5 Solve Mode – page 5 Scramble Mode – page 5 Undo Mode – page 5 Hint Mode – page 5 Sound Control Mode – page 6 Display Mode and Charging Information – page 7-9 Reset Reset Information – page 7-8 NOTE: Please follow the icons on each side for the product’s features. Colors may vary.
Solve – Double tap to begin Solve Mode. Undo – Double tap to activate Undo Mode. Sound Control – Double tap to enter Sound THE CHARGING DISPLAY STAND Recharge light Red – Charging Green – Fully Charged Contact points – Align contact points on your TouchCube with the ones on the base (Solve cubie should face the back of base) and make sure the recharge light is lit to ensure that the TouchCube is charging. Reset area – Press the TouchCube to the bottom of the charging display stand to restart the Cube.
BASIC CONTROLS Horizontal/Vertical Rotation – To eliminate accidental moves, your TouchCube’s Swipe built-in accelerometer only activates the top face. Turn the Cube to the side you want to move and swipe horizontally or vertically on the active face to move three adjacent cubies in a row or column. The TouchCube works and moves just like a regular Rubik’s ® Cube! Swipe Tips • The TouchCube moves rows or columns just like the original Rubik’s ® Cube so you cannot move the lights diagonally.
FUNCTIONS Function modes can be activated as detailed below. Besides the On/Off cubie, every center/function cubie can only be used when its side is facing up and active. Most functions require a double tap – similar to a double-click with a computer mouse. Simply press twice on the center/function cubie quickly to activate these functions. Power Mode – Press and hold the On/Off cubie to power the TouchCube On or Off.
FUNCTIONS (cont) Sound Control Mode – Double tap the Sound Control Mode cubie to enter the Sound Control Mode. First, select the mode of SFX you would like the TouchCube to play. If the Sound Control face is yellow, this Clockwise: Counterclockwise: Increase Volume Decrease Volume indicates the TouchCube is in Classic sound mode, an exact recording of the original Rubik’s ® Cube. If the face is blue, it is in Modern sound mode, which is a pleasant swipe sound.
DISPLAY CHARGING MODE & RECHARGING YOUR TOUCHCUBE Your TouchCube will enter Display Mode while recharging, scrambling and then solving itself to create a captivating show when you are not playing with it. Recharge your TouchCube by placing it in its included recharging display stand. Make sure the Solve Mode cubie is facing the back of the stand (where you plug in the adapter). The On/Off cubie should face front and line up with the recharge light.
If the TouchCube is still stuck or frozen, you can perform a second level reset by pressing the Undo Mode cubie and holding it down for 1.5 seconds. Then, while holding down the Undo Mode cubie, press and hold down the On/Off cubie for 1.5 econds. The TouchCube will flash and then reset. If your TouchCube continues to malfunction for any reason after a second level reset, turn it off and leave it powered down for 5 minutes. When you restart your TouchCube, it will operate normally.
The TouchCube and the charging display stand may become warm during normal use. Always allow adequate ventilation around the TouchCube & charging display stand away from flammable items, using care while handling them. Do not attempt to open or service this product yourself as doing so will void your warranty. Please contact Techno Source’s Customer Assistance regarding any troubleshooting or repair questions.
FREQUENTLY ASKED QUESTIONS & TROUBLESHOOTING The TouchCube is not charging properly Please ensure that the back of the stand (where you plug in the adapter) is lined up with the Solve Mode Cubie on the TouchCube. You may need to adjust the position of the Cube slightly to make sure that the contact points on the Cube have a strong connection with the ones on the recharging display stand. If the TouchCube still does not charge, please reset it with the designated reset area.
WARRANTY & SERVICE INFORMATION Techno Source’s warranty obligations for this hardware product are limited to the terms set forth below: HARDWARE WARRANTY Techno Source USA warrants to the original purchaser that the hardware product shall be free from defects in material and workmanship under normal use for ninety (90) days from the date of retail purchase.
NOTES
www.rubikstouchcube.com www.technosourceusa.