User's Manual
Table Of Contents
- OPERATING INSTRUCTIONS
- 1.1 Controls and Display
- 1.2 Transceiver Basic Operation
- 1.3 About Commands
- SECTION 2
- 2.1 Channel Operating Parameters
- 2.2 Editing Channel Operating Parameters
- 2.3 Scan and Multi-Mode Operation
- 2.4 Controlling User Access
- 2.5 Encrypted Operation
- 3.1 Operator Level 1 Commands
- 3.1.1 Select the Operating Memory for the Main Channel
- 3.1.2 Increase Display Brightness
- 3.1.3 Edit Channel Operating Mode
- 3.1.4 Scroll Backwards through Available Memories
- 3.1.5 Start/Stop Scan
- 3.1.6 Scroll Forewards through Available Memories
- 3.1.7 Edit Channel Operating Frequency
- 3.1.8 Decrease Display Brightness
- 3.1.9 Edit Channel Squelch Mode
- 3.1.10 Command Level Up
- 3.1.11 Toggle memory: current/home
- 3.1.12 Toggle Talk Around
- 3.1.13 Erase Encryption Keys
- 3.2 Operator Level 2 Commands
- 3.2.1 Create/Edit All Channel Information
- L2-1.1. Entering a Memory Number (refer to L1-1 for details)
- L2-1.2. Enter a Scan List & Enabling/Disabling Scan (refer to L2-5 for details)
- L2-1.3. Enter a Text Description (refer to L2-6 for details)
- L2-1.4. Enter an Operating Mode (refer to L1-3 for details)
- L2-1.5. Enter a Frequency (refer to L1-7 for details)
- L2-1.6. Enter the Squelch Parameters (refer to L1-9 for details)
- 3.2.2 Copy Guard to Main
- 3.2.3 Lock Keypad
- 3.2.4 L2-4 not used.
- 3.2.5 Edit Scan List & Enable/Disable Scan
- 3.2.6 Edit Memory Text Description
- 3.2.7 Create Shadow Memory
- 3.2.8 Copy Main to Guard
- 3.2.9 Encryption ON/OFF
- 3.2.10 Command Level Up
- 3.2.11 Command Level Down
- 3.2.12 L2–#. Not Used.
- 3.2.1 Create/Edit All Channel Information
- 3.3 Operator Level 3 Commands
- 3.3.1 Select Boot Channel
- 3.3.2 Assign Key by KeyTag
- 3.3.3 Set Numeric Edit Mode: Decimal or Hexadecimal
- 3.3.4 Display Firmware Release and Version Information
- 3.3.5 Edit Scan Parameters
- 3.3.6 Configure PTT Timer
- 3.3.7 Side Tone Audio Level Adjust
- 3.3.8 PC Data Upload/Download
- 3.3.9 Display Channel Squelch Parameters
- 3.3.10 Command Level Up
- 3.3.11 Command Level Down
- 3.3.12 Unused
- 3.4 Maintenance Commands (Level 4)
- 3.4.1 Set Default Record
- 3.4.2 Set Restricted Level Access Mode
- 3.4.3 Set Command Permissions
- 3.4.4 Set Memory Edit
- 3.4.5 L4-5. not used
- 3.4.6 L4-6. not used
- 3.4.7 Set Frequency Display
- 3.4.8 Assign KeyTags to Encryption Keys
- 3.4.9 Set Squelch Restrictions
- 3.4.10 Command Level Up
- 3.4.11 Command Level Down
- 3.4.12 L4-# not used
- 3.5 Supervisor Commands (Level 5)
- 4.1 Appendix A. Installing the Jumper for Restricted Level Access.
- 4.2 Appendix B. CTCSS Tone and DCS Code Tables
- 4.3 Appendix C. Programming Channel data using TDP and a PC.
- 4.4 Appendix C. 2.5 kHz & 6.25 kHz Valid Frequencies
- 4.5 Appendix D. Default Tables
TDFM-136B Operating Instructions 08RE399
3.1.8 Decrease Display Brightness
Level 1 Key Scope: Main and Guard
Press and hold the down arrow (8) key to decrease the brightness of the LED character display, it
stops when the key is released or at minimum, whichever occurs first.
3.1.9 Edit Channel Squelch Mode
Level 1 Key Scope: Main and Guard
Select the Squelch Mode for the active memory (determined by front panel switch positions), and
edit the value if applicable. Note that the scope of the command is subject to restrictions imposed
by the Squelch Permissions – see L4-3. Edit Squelch is a duplex command: Receive followed by
Transmit. At start the cursor appears at the Squelch Mode indicator position as follows:
Figure 3-6 . Editing the Squelch Mode
Edit Keys
step up/down through available squelch modes.
accept the entry and exit
abandon the entry and exit
The available options are constrained by the operating mode as per table 3-3.
Table 3-3. Receive and Transmit Squelch Modes
Analog
Digital
Rx
Tx
Rx
Tx
Noise
CTCSS Tones
Monitor
3
TalkGroup + NAC
B
CTCSS Tones
DCS Codes
NAC Only
ID Call
DCS Code
Inhibit
"
TalkGroup + NAC
B
Inhibit
"
Once the Squelch Mode has been selected, if applicable, the user will be allowed to edit the value
of the selected mode (subject to restrictions imposed by the Squelch Permissions – see L4-3).
Analog - Noise Squelch Value
Scope: receive only, range 0-16 ($0-$F)
If Noise (Rx) is chosen, the prompt line will display the current value for noise squelch level and
place the cursor on the first digit available for the user to edit:
Figure 3-7 . Editing the Noise Squelch Value
Technisonic Industries Ltd. 31
+!)*#$%&'
,-./