Quick start manual TechniMedia UHD
EN 1 Illustrations TV connections / Local control FR IT 1 2 3 4 5 22 23 6 7 8 9 10 11 12 13 14 15 16 17 18 Connections 1 Common Interface 2 Card reader 3 Audio output analogue (3,5 mm jack plug) 4 Headphone output (3.
EN 1 Illustrations FR IT On/Standby Sleep Timer Remote control code Sound on/off Numeric keypad keys Recording TV/Radio mode Stop / DVR Rewind 0/AV (source selection) Fast forward Pause / playback Arrow keys SFI WWW Page up Page down Back Info OK Options selection Volume +/- Channel +/- Function selection Function keys/off Zoom/Format Audio channel PiP / PaP / PaT Genre Menu Timer Teletext Freeze frame / Jogshuttle 3
2 Please read this first EN Dear customer, FR This quick start guide only describes the most important connection options and the basic operating steps to enable you to start operating the TechniMedia UHD quickly, and does not replace the operating manual. Many additional functions are described in the operating manual that are not mentioned in this quick start guide.
3 Connecting a EN Connection/s connecting the satellite antenna to LNB-Input 1/LNB-Input 2 When operating with an antenna signal, the LNB must be connected to LNB Input 1. b Connecting the cable connector (digital and/or analogue) and/or the DVB-T antenna to the antenna input on the TV. c Connecting the television to a BluRay/DVD player using an HDMI cable. d Connecting the digital audio output to a surround sound system.
EN FR IT The following references (a b c) refer to the connection example on page 5. 3.1 Satellite antenna a Connect the LNB inputs 1 / 2 using two separate antenna feed cables that are set up identically to be able to use the full range of functions. or If there is only one antenna signal available, connect this to LNB input 1 on the television. Also note points 7.16, 8.1 and 10.6 of the operating manual. 3.
4 Basic operation EN Dear Customer, FR The following section starts by covering basic operation as well as recurrent operating steps for the TV. This should make it easier to read the instruction manual, since it avoids repeated description of identical steps at each individual stage. IT If it is necessary for a function or setting for the TV to be different from the basic operation, the difference in operation is described in detail in the relevant section in the instruction manual.
EN 4.2 Calling up the main menu and navigating through the menus / functions FR The following example will illustrate how you reach the main menu and call up a submenu. The objective of the example is to call up the Picture settings menu. IT > Press the Menu button. The main menu appears on the screen. > Select the Settings menu item by using the arrow keys to move the highlight to this item. > Press the OK button to open the Settings menu.
> Use the up/down arrow keys to highlight the Picture settings item. EN FR IT > The Picture settings menu is opened by then pressing the OK button. You can also highlight the individual menu items in the same way as you highlight an item on a submenu to open it and alter the respective settings. The menu items in some menus have to be highlighted by moving sideways. This is done by pressing the right/left arrow keys.
EN FR IT 4.3 Accepting settings / Exiting menus and functions In some menus and functions the changes made must be accepted manually in order to save them permanently. If this does not happen, the function or the values that existed before the change was made will be reset automatically on exiting the menu. If an Accept field or the green function key with Accept is displayed in the bottom line of the screen, you can see that the changes made must be saved manually to be accepted.
4.4.1 Arrow selection method > EN If is shown on the left and on the right, next to the set value, you can alter this using the left/right arrow keys. IT 4.4.2 Selection list If is shown on the right, next to the set value, the value is changed using the selection list. > Press the OK button to open the selection list. > Highlight the setting you want using the up/down arrow keys.
EN FR 4.4.3 Entering numbers > IT Enter the new setting you want using the numeric keypad key if a question mark or a number value or is shown inside the highlight. Note the number of digits used in the entry since there must always be the same number used. This means that if a five-digit value is required, for example "10600", but you only wish to set a four-digit value, for example "9750", then you must enter a "0" at the beginning for every unused position.
The SMS keyboard is operated using the numeric pad on both the alphabetic and the QWERTY keyboard and can be used at any time. The coloured buttons thus incorporate the functions described above. > Press one of the numeric pad keys 0 - 9 and select the various letters, numbers, characters and symbols. The first letter of the respective row of characters is highlighted after first pressing a numeric pad key.
EN 4.5 Options selection FR In some menus and operating modes (e.g. TV mode, music/images playback etc.), you have the option of calling up additional functions and options via the options selection IT function. > Press the Options button to open the options selection function in the lower right-hand corner of the screen. In this example we can see the options selection for the channel list. > Each additional press of the Options button moves the highlight down one line each time.
5 Initial installation EN During initial installation of the TV, the AutoInstall installation wizard starts automatically. Using the installation wizard is the simplest way for you to create the most important settings for your TV. The initial installation shown here simply serves as an example. The exact process for the initial installation will depend on the settings you select. Therefore please follow all instructions displayed on screen carefully.
EN Display mode FR IT > Use the up/down arrow keys to select your preferred display mode and confirm by pressing the OK button. You can change the selected display mode again to whatever you want after AutoInstall, as described in section 10.1 of the instruction manual. When using the intense or natural image modes, observe the information displayed and points 3.3.3, 7.10 and 10.1 of the operating manual and confirm by pressing the OK button.
Number of antenna signals (DVB-S) EN Select the number of attached DVB-S antenna feed lines. If the DVB-S source has been disabled, this page of the installation wizard does not appear; you are taken directly to the “Antenna settings (DVB-T)” page instead. > Use the right/left arrow keys to select the attached antenna signals and confirm by pressing the OK button. Antenna configuration (DVB-S) In this step of the installation you can adjust your TV setup to the configuration of your satellite antenna.
EN Antenna configuration (DVB-T) FR In this step, a channel range is displayed with the signal levels of the channels so you can align the DVB-T antenna to ensure optimal reception. The “channel search / ISIPRO” appears immediately if DVB-T has been disabled. IT > Use the up/down arrow keys to highlight the Antenna supply field and confirm by pressing the OK button. > Switch the antenna feed on and off using the up/down arrow keys to highlight to relevant input and confirm with OK.
Channel search / ISIPRO - DVB-S only EN FR IT > To download the available current channel list, use the up/down arrow keys to highlight the ISIPRO - service list update line and start the process by pressing the OK button. After the service list update, an automatic channel search on all other configured reception sources is then carried out via “All Channels”.
EN Software updates FR IT > If you do not want to wait for a search for new software or a software download, you can, if necessary, skip this step by pressing the Info button. > If there is no new TV software available, you can press the OK button to go to the next step in the installation wizard. > If, on the other hand, new TV software is found, the automatic software update can be started by pressing the OK button. While doing this also observe items 15.5 and 18 in the instruction manual.
watchmi > EN Select the desired option using the arrow keys and then confirm by pressing the OK button. FR IT Off The watchmi service is switched off. On The watchmi service is switched on. Please also note the further instructions and explanations regarding watchmi under point 7.26 of the operating manual. Loading SFI data In order that the data in the electronic programme guide SFI (SiehFernInfo) can be displayed, you must first download it.
EN Product registration FR By registering your product you secure further benefits and help us to tailor our products and services to suit you even better. IT Please note that an Internet connection is required to do so. Exiting the installation wizard > Confirm the final message from the installation assistant by pressing the OK button. 6 Operating the unit 6.1 Switching the TV on and off 6.1.
process takes several seconds to complete. 6.1.2 Switching on from standby mode > Switch the TV on by pressing the On/Standby button on the remote control or on the TV, or the Channel +/- keys on the remote control or on the TV, or a numeric key between 0 and 9 on the remote control. If the user-dependent parental lock (TechniFamily) outlined under point 10.9 of the operating manual is activated, the user selection as per point 7.1.3 of the operating manual will now be displayed. 6.1.
EN 6.2 Selecting a channel FR 6.2.1 Using the channel up/down buttons IT > You can switch between channels one at a time using the Channel +/- buttons on the remote control or on the TV. 6.2.2 Using the numeric pad keys > Use the numeric keypad keys to enter the number of the channel you want.
6.2.3.2 Selecting a list EN To make it easier for you to find channels, your device provides various channel lists. You can select your favourite’s lists or display the channels sorted alphabetically from the list of all channels, the TV provider lists or according to genre. > Press the OK button to open the active channel list. > Using the right/left arrow keys you can now select your favourite’s lists and the overall list and, using the Option selection function, you can filter the channel list (e.g.
EN FR IT 6.3 AV source > Press the AV button to open the AV sources selection window and select a device connected to the TV’s HDMI inputs (HDMI 1 / 2 / 3) or to the Scart socket (EuroAV). > Select the source you want using the up/down arrow keys and confirm by pressing the OK button to switch over to the selected input. To do this also observe items 7.2.1 - 7.2.3, 7.2.6, 10.9 and 12 in the instruction manual. 6.4 Channel/source information 6.4.
EN 6.5 Receiving encrypted channels > FR Insert a CI-/CI+ module into the slot with the top facing to the back and insert the Smartcard into the card slot in the CI-/CI+ module, with the golden chip to the rear and pointing in the direction of insertion or > Insert the Smartcard into the device’s card reader with the golden chip to the front and pointing in the direction of insertion. When doing this you should also observe point 7.5 of the operating manual. 6.5.
EN FR IT The sound modes can be configured as desired as described in point 10.2 of the operating manual. 6.9 Display mode Using the image mode selection function you can switch between the Economic (home use), Natural (standard), Intense (presentation), Film (Cinema) and PC (Graphics) image modes directly during operation. > You can select the sound you want using the sound mode item in the Options selection. The image modes can be configured as desired as described in point 10.
6.13 Format switchover / Zoom > EN Pressing the Zoom/Format button allows you to select the various pre-defined formats (original, optimum, optimum 16:9, full zoom and stretch) as well as the user-defined setting, where you can adjust the picture as you wish.
EN FR IT 6.17 SFI programme information guide Your TV has SFI electronic programme information. You can use this to display programme information for a single or a number of digital channels on the screen and to obtain a very quick overview of the current programmes, or programmes being broadcast that day, or on subsequent days. To do this also observe sections 7.18 and 10.8 of the instruction manual. > Press the SFI button to call up the electronic programme guide.
6.18 Selecting a function > EN You can open the Navigation menu (NAV menu) to select the function you want by pressing the function selection button. FR IT To do this also observe sections 7.21 and 10.9 of the instruction manual. 6.19 HbbTV The symbol application. in the infobox indicates that the broadcaster provides an HbbTV > Switch on the HbbTV function via Option selection under HbbTV on so that it can be used for the current operating phase.
EN 6.20 Internet FR Your device can use an existing broadband connection to access the Internet. To do this, the TV must be connected to your home network/DSL router via either LAN or WLAN. IT Internet access provides you with various Internet functions such as unrestricted browsing, use of interactive services, video on demand and the new ISIO Live TechniSat service portal. When using this please be sure to note the messages and displays on the screen as well as sections 7.25, 10.4.1 and 10.4.
6.20.1.1 Selecting a list EN Your TV provides various Internet lists to make it easier for you to find web links. You can select and display all your configured Favourite lists as per section 13. FR > Use the Internet lists item in the Options selection to select the Internet list you want. 6.20.1.2 Filtering by genre > Using the Option selection > View option you can configure the way the currently displayed Internet list is sorted.
EN FR IT 6.20.3 Navigating in the open website > Once the desired website has loaded and is displayed, depending on the setting under point 10.5.2.6 of the operating manual, either a highlighted area/frame or term/text appears, or the mouse cursor appears at a position on the screen. > You can use the arrow keys to move the highlight/frame, or the cursor, to the areas provided (e.g. a forwarding link, a button, dropdown list etc.). > The associated action is accepted by pressing the OK button.
6.20.9 Ending Internet use > EN To switch from a web page you have called up back to normal mode, press the WWW >To switch to TV/Radio mode from an accessed web site, press the TV/Radio button or press the WWW button three times. 7 Operating the DVR The DVR function (DVR=Digital Video Recorder) means you no longer have to use an external recorder (e.g. video or DVD recorder) to record programmes, as you can use this function to record them to a USB storage device.
EN FR IT 7.1.3 Ending manual recording > First select the recording to be ended by selecting the channel on which the recording is running as described under section 6.2 of the quick start manual. > Pressing the Stop button generates a query as to whether the recording should be stored or discarded. > Select Store to save the recording, or Discard not to save the recording, or Back to continue with the recording. 7.1.
EN FR IT > You can start to playback a recording by highlighting it and then confirming with OK. In doing so also be absolutely sure to observe section 10.9 in the instruction manual. The broadcast information can be displayed and hidden by pressing the Info button repeatedly. 7.2.1.1 When in TV mode > In TV mode press the Stop / DVR button to switch directly to the DVR Navigator.
EN FR > During playback press the Fast forward or Rewind button. The message uu or tt appears in the aforementioned small infobox. The film is now played back at 4x speed, in the chosen direction. > If you press the Fast forward or Fast rewind button again, the speed will increase to 16x and the message uuu or ttt appears. > If you press the Fast forward or Fast rewind button again, the speed will increase to 64x and the message uuuu or tttt appears.
2235543951001
