X800 Owner’s Handbook Picture Frame
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. IMPORTANT SAFETY INFORMATION Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a slightly damp cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
CONTENTS SAFETY INFORMATION.................................................................................................2 INTRODUCTION............................................................................................................4 UNPACKING.................................................................................................................4 CONTROLS AND FUNCTIONS.........................................................................................5 REMOTE CONTROL HANDSET.....
IINTRODUCTION UNPACKING Your Digital Picture Frame (DPF) enables you to view digital pictures from either a memory card or from a USB drive. The DPF is compatible with the following card formats: SD™ (Secure Disk), MMC™(Multimedia Card), MS™ (Memory Stick) and SDHC (Secure Disk High Capacity). The Frame will also support a USB 2.0 or 1.1 drive.
CONTROLS AND FUNCTIONS 1 2 3 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 4 5 6 7 5V DC Input Socket USB Socket SD/MMC/MS Card Slot Display Screen Remote Control Sensor Detachable Stand MENU/OPEN OSD Key Navigation Keys* EXIT (Return) key ON/OFF Switch Stand Attachment 8 9 10 11 *NAVIGATION KEYS 1. Play/Pause; Confirm/Enter; hold to enter main menu 2. Previous/Left button 3. Down button; Rotate photo while playing a slideshow 4. Next / Right button 5.
REMOTE HANDSET HANDSET KEYS AND FUNCTIONS 1 Press to set the player in and out of Standby. 2 Press to move the cursor upward. 3 Press to move the cursor leftward or select the previous picture. 4 MENU Press to return to the main menu. 5 Press to move the cursor downward. 6 Press to select the previous picture when viewing pictures Switch to the previous page in thumbnail mode. 7 Press to zoom the picture. 8 Press to select 4:3 or 16:9 aspect ratio for a picture 9 SETUP Press to go to the setup menu.
PLACEMENT Remove the mount from the magnetic clip at the rear of the frame. Insert it into the attachment hole. Twist the mount clockwise until it attaches firmly to the frame. After the mount has been attached, you can set the DPF in the landscape or portrait orientation. GETTING STARTED HANDSET PREPARATION Remove the protective strip from the battery compartment to activate the battery. If the handset behaves erratically or fails to operate the battery should be replaced.
CONNECTING POWER If the DPF is being switched on for the first time, or after a default setting reset, you must first select a display language. Use the ( ) or ( ) buttons on the DPF or the buttons on the handset to make your selection. Press the button on the DPF or OK on the handset to confirm. In the next screen, Use the ( ) or ( ) buttons on buttons on the DPF or the the handset to select YES or NO. ON Press the YES NO button on the DPF or OK on the handset to confirm.
INSTALLING A USB DEVICE OR MEMORY CARD To insert a memory card. Position the card with the cropped corner facing the bottom of the screen and press gently in. To release a memory card. Grip both sides of the card and gently pull out. SD Card, etc When first switched on the pictures will display as a Slide Show. Thereafter the display will depend on the setup you have customised.
When the Zoom is positive (i.e greater than 1) • Press the keys to pan the picture to left or right • Press the keys to pan the picture up or down • To resume slideshow play: cycle Zoom to Normal and press OK. VIEWING PICTURES Switch the ON /OFF switch on the frame to ON or press the button on the handset to bring the frame out of Standby. If there is a memory device inserted the device will start a slideshow. When the frame detects a memory devices it displays all the viewable images.
NAVIGATING A SLIDESHOW VIA THE OSD MENU During a slideshow: Press the OSD key The OSD menu appears on the screen and slideshow pauses. 3 To zoom in the picture, highlight and press the OK key. When a picture is magnified • Press the keys on the handset to pan the picture left / right. • Press the keys on the handset to pan the picture up / down. • Press the OK key again to resume normal slideshow play. 4 To rotate the picture to the left, highlight and press OK.
Accessing Thumbnail Mode from the Main Menu THUMBNAIL MODE You can enter thumbnail mode in two ways: During a Slideshow: Press the key. Switch the ON /OFF switch on the frame to ON. or Press the key to bring the frame out of standby Press MENU to display the main menu Press the or key on the handset to select a memory device. Press OK: Thumbnail Mode will deploy. The pictures display in pages of 15 thumbnails. The picture you were viewing is highlighted. Picture details appear at the bottom.
Press or to select the Slide Show Time. Press OK to enter the menu and display the menu contents. The Sliding Show Time. alters the time each slide displays on screen. Press or to select a Slide Show Time. Press OK to confirm and return to the Setup Menu. SYSTEM SETUP Access the Main Menu. Select SETUP: Press OK. (You can also press the SETUP key on the handset to enter Setup) Slide Show Time 3s Transition Effect 3s Language 15s Brightness Contrast Press or to select Transition Effect.
Setting the Language The language setting affects all the menus and selections in the DPF. These parameters are all set in the same manner. There are seven settings +3,+2,+1, 0, –1, –2, –3. The changes display immediately. Press or to select Brightness/Contrast/Saturation. Press OK. Press or to select a parameter. Press OK to confirm and return.
DEFAULT This setting returns the DPF to factory settings. Slide Show Time YES Transition Effect NO TROUBLESHOOTING If your DPF seems not to be working as well as you might expect, please work through this checklist before returning the product to Tesco. The DPF will not switch on. Switch off, Check the power supply connections, switch on again. The DPF will not recognise a memory card. Re-insert the card. You may need to reformat the card. The DPF will not play pictures on a card.
AFTER USE Though you can leave the frame in Standby indefinitely we do not recommend this for the following reasons: • The connected AC adaptor cable could be a source of danger. • You will consume power unnecessarily. Otherwise, switch the set off via the POWER switch. Unplug the adaptor from the mains and then unplug the adaptor from the DPF. Unplug any memory card or USB stick. Store the unit and power adaptor in a cool dry place, out of the reach of children and pets.
