OPERATING INSTRUCTIONS LCD40-920 COLOUR TELEVISION WITH REMOTE CONTROL For assistance, please call our Tesco Electrical Helpline on 0845 4566767 Downloaded from www.Manualslib.
Contents Features ................................................................. 2 Accessories ............................................................ 2 Introduction ............................................................. 2 Preparation ............................................................. 2 Safety Precautions ................................................. 3 Power Source ..................................................... 3 Power Cord ...............................................
Accessories Features • Remote controlled colour LCD TV. • Fully integrated digital TV (DVB-T). • HDMI connectors for digital video and audio. This connection is also designed to accept high definition signals. EPG SCREEN • 200 programmes from VHF, UHF(analogue). • 300 programmes for digital mode (IDTV). • OSD menu system.
Safety Precautions Please read the following recommended safety precautions carefully for your safety. Power Source The TV set should be operated only from a 220-240 V AC, 50 Hz outlet. Ensure that you select the correct voltage setting for your convenience. Power Cord Do not place the set, a piece of furniture, etc. on the power cord (mains lead) or pinch the cord. Handle the power cord by the plug.
Headphone Volume Excessive sound pressure from earphones and headphones can cause hearing loss. Installation To prevent injury, this device must be securely attached to the wall in accordance with the installation instructions when mounted to the wall (if the option is available). LCD Screen The LCD panel is a very high technology product with about a million thin film transistors, giving you fine picture details.
Overview of the Remote Control 1. Standby 2. Yellow / Feature menu / Current language (*) (in DTV mode) 3. Blue / Install menu / Favourite mode (*) (in DTV mode) 4. PIP / PAP mode EPG 5. Guide (in DTV mode) SCREEN LANG SUBTITLE SLEEP 6. Sleep timer 7. Subtitle on-off / TXT subtitle 8. Numeric buttons DEF 1 2 3 JKL MNO PQR 6 9. TV – Digital TV mode 10. Volume up 11. Programme up / Page down (in DTV mode) GHI ABC 4 5 STU VWX YZ 7 8 9 FAV 0 TV DTV V 12. AV / Source selection 13.
LCD TV and Operating Buttons 1. Standby button 2. TV/AV button 3. Programme Up/Down buttons 4. Volume Up/Down buttons ” / “ ” Note: Press “ buttons at the same time to view main menu. Viewing the Connections- Back Connectors 12 1. S/PDIF Digital Out outputs digital audio signals of the currently watched source. Use a digital optic cable to transfer audio signals to a device that has S/PDIF input. 2.
5. SCART 1 inputs or outputs for external devices. Connect the SCART cable between SCART sockets on TV and SCART socket on your external device (such as a decoder, a VCR or a DVD player). Note: If an external device is connected via the SCART sockets, the TV will automatically switch to AV mode. If both sockets are employed at the same time, SCART 1 will override SCART 2 unless manually selected. Note: You should connect the decoder to EXT-1, if you are planning to watch a scrambled channel.
Viewing the Connections - Side Connectors 1. CI Slot is used for inserting a CI card. A CI card allows you to view all the channels that you subscribe to. For more information, see “Conditional Access” section. 2. Headphone jack is used for connecting an external headphone to the system. Connect to the HEADPHONE jack to listen to the TV from headphones (optional). 3. Video Input is used for connecting video signals of external devices.
Power Connection IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz. • After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. • You may also connect through the SCART 1 or SCART 2. Use a SCART cable as shown below. Note: These three methods of connection perform the same function but in different levels of quality. It is not necessary to connect by all three methods. • Plug the power cable to the mains socket outlet.
Using Other Connectors You can connect a range of optional equipment to your LCD TV. Possible connections are shown below. Note that cables shown in the illustration are not supplied. • To connect external speakers, use an audio cable. Do not reverse the AUDIO LEFT and AUDIO RIGHT jacks. Turn on the LCD TV and external speaker set after all connections are made. Refer to your speaker set’s manual for further queries.
Operation with the Remote Control Input Selection Once you have connected external systems to your TV, you can switch to different input sources. • Press “SOURCE” button on your remote control for directly changing sources. or, • Select “Source” option from the main menu by using “ ” or “ ” button. Use then “ ” or “ ” button to highlight an input and press “ ” button to select. Note : You can mark desired source options by pressing the OK button.
If an active antenna is connected to your TV, you can select this option as On. Antenna power should be “Off” when standard antenna is used instead of the active antenna. See Configuration Menu in the following sections for more information. Press OK button on the remote control to continue and the following message will be displayed on the screen: Select your Country, Language and Text language by using “ ” or “ ” and “ ” or “ ” buttons. Press OK or RED button to continue.
• Press EPG button to view the EPG menu. • Electronic Programme Guide appears on the screen. It is able to get Information of the channel - programs weekly by means of 7-DAY-EPG. All programs of channels are displayed. On the bottom of the screen; info bar, showing all the available commands, will be displayed. following warning message display on the screen (* for UK only): Digital Teletext (** for UK only) • Press the TELETEXT ( ) button. • The digital teletext information appears.
Moving the channels in the channel list IDTV Menu System The IDTV menu can only be viewed when watching digital terrestrial broadcasting. Press the “ ” button to turn IDTV on while the TV is in analogue mode. • Press “ ” or “ ” buttons to select the channel that will be moved. • Press “ ” or “ ” buttons to select the “Move” item on Channel List menu. Press the “M” button. The menu below appears on the screen: Note: If you enter the same programme number of the channel that you want to move, “....
Renaming Channels Setting Favourites To rename a specific channel, the channel must be highlighted by pressing “ ” or “ ” button. Then highlight the Edit Name item by pressing “ ” or “ ” button as illustrated below. Press the OK button to activate the rename feature. To set a favourite you should highlight the “Favourites” item at the bottom of the Channel List menu. Then press OK button and Edit Favourite List menu appears on the screen.
on the remote control. Then “Add Timer” window appears. Channel: “ ” or “ ” keys will navigate the user through the TV or Radio list. Date: Starting date is entered via the Left/Right or the numeric buttons. Start: Starting time is entered via the Left/Right or the numeric buttons. End: Ending time is entered via the Left/Right or the numeric buttons. Duration: Duration between Start and End time. Repeat: You can set a timer to be repeated as Once, Daily or Weekly.
channels as well. If it is set as OFF manually, encrypted channels will not be located while in automatic search or manual search. Use “ ” or “ ” button to select Scan Encrypted and then press “ ” or “ ” button to set this setting as On or Off. Receiver Upgrade Over Air Download (OAD) Dolby D Digital (* for EU countries only) (optional) In the Configuration Menu, highlight the Dolby D item by pressing “ ” or “ ” buttons. Use the “ ” or “ ” buttons to set the Dolby D Digital as On or Off.
Parental Control Use “ ” or “ ” buttons to go to Parental Lock option. Press OK button to enter the menu. A dialog box asking for the lock key will be displayed. The key is set to “0000” initially. Enter PIN. If it is incorrect, “Wrong Pin” OSD will be displayed. If it is correct, the Parental Control menu will be displayed: screen. Current Time,Time Zone Setting and Time Zone will be available. Use “ ” or “ ” buttons to highlight the Time Zone Setting. Time Zone Setting is set using “ ” or “ ” buttons.
In the configuration menu, highlight the Language Settings item by pressing “ ” or “ ” buttons. Press OK and Language Settings submenu will be displayed on the screen: Use “ ” or “ ” buttons to highlight the menu item that will be adjusted and then press “ ” or “ ” button to set. Notes: • System Language determines the on-screen menu language. • Audio Language is used for selecting the soundtrack of a channels.
First Time Installation The user can use this item to load default settings, which were loaded to the receiver at the factory. To install factory settings, highlight “First Time Installation” menu item and press OK button, then you will be asked whether or not to delete the settings. Selecting “Yes” by pressing OK button while the “Yes” is highlighted will delete the existing channel table.
Press “ ” or “ ” button to select Film Mode. Analogue TV Menu System Press “ ” or “ ” button to set this feature On or Off. Picture Menu Turn this feature on when you are watching. films to see the fast motion scenes clearly. Game Mode Select Game Mode by pressing “ ” or “ ” button. Use “ ” or “ ” button to set Game Mode as On or Off. When Game Mode is set to On, specific game mode settings, which are optimized for better video quality, will be loaded.
Volume PIP/PAP : PIP/PAP window sound. Press “ ” or “ ” button to select Volume. Press “ ” or “ ” button to change the level of the Volume. Active : Sound of the current selection. Inactive : Sound of the currently inactive window. Equalizer Sound Mode (optional) Press “ ” or “ ” button to select Equalizer. Press “ ” button to view equalizer menu. Press “ ” or “ ” button to select Sound Mode.
Note: See Appendix E for all PIP/PAP modes. Sleep Timer Press “ ” or “ ” button to select Sleep Timer. Use “ ” or “ ” button to set the Sleep Timer. The timer can be programmed between Off and 120 minutes in steps of 10 minutes. If Sleep Timer is activated, at the end of the selected time, the TV goes automatically to standby mode. Child Lock Press “ ” or “ ” button to select Child Lock. Using “ ” or “ ” button, you can switch to PIP, PAP mode or turn off the feature.
Band Press “ ” or “ ” button to select Menu Timeout. Use “ ” or “ ” button to change menu timeout to 15 sec, 30 sec or 60 sec. Band can be selected either C or S. Press “ ” or “ ” button to set Band. Teletext Language Channel Press “ ” or “ ” button to select Teletext Language. Use “ ” or “ ” button to change Teletext Language to West, East, Turk/Gre, Cyrillic, Arabic or Persian. Channel can be changed by “ ” or “ ” button or numeric buttons.
Store Press “ ” or “ ” button to select Store Program. Press “ ” or OK button to store the settings. “Stored...” will be displayed on the screen. Program Table Select Program Table by pressing “ ” or “ ” button. Country Press “ ” or “ ” button to select your country. If you want to exit from A.P.S. function, press the BLUE button. By moving the cursor in four directions you can reach 20 programmes in the same page.
Source Menu Press “ ” or “ ” button and select the sixth icon. Then press “ ” or OK button. Source menu appears on the screen: Select Autoposition item by using “ ” or “ ” buttons. Press OK or “ ”, “ ” button. Warning: Please ensure auto adjustment is performed with a full screen image to ensure best results. H (Horizontal) Position This item shifts the image horizontally to right hand side or left hand side of the screen. Select H Position item by using “ ” or “ ” button.
Displaying TV Information Zoom Modes Programme Number, Programme Name, Sound Indicator and Zoom Mode information is displayed on the screen when a new programme is entered or “INFO/ ” button is pressed. Mute Function To cancel mute, there are two alternatives; the first one is pressing the “ ” button and the second one is increasing the volume level.
14:9 This zooms up the wide picture (14:9 aspect ratio) to the upper and lower limits of the screen. Press once to enlarge top half of the page, press again to enlarge the bottom half of the page. Press again to revert back to normal size. “ ” Reveal Shows hidden information (e.g. solutions of games). “OK” Hold Holds a text page when convenient. Press again to resume. Cinema This zooms up the wide picture (16:9 aspect ratio) to the full screen.
Remote Control Tips Screen Care Clean the screen with a slightly damp, soft cloth. Do not use abrasive solvents as they may damage the coating layer of the TV screen. For your safety, unplug the mains plug when cleaning the set. When moving the TV, hold it properly from the bottom part. Image Persistence Your TV no longer responds to the remote control. Perhaps the batteries are exhausted. If so you can still use the local buttons at the bottom of the TV.
Appendix A: PC Input Typical Display Modes Appendix B: AV and HDMI Signal Compatibility (Input Signal Types) The display has a maximum resolution of 1920 x 1200. The following table is an illustration of some of the typical video display modes. Source Your TV may not support different resolutions. Supported resolution modes are listed below. EXT-1 (SCART 1) If you switch your PC to an unsupported mode, a warning OSD will appear on the screen.
Appendix C: Supported DVI Resolutions When connecting devices to your TV’s connectors by using DVI converter cables (not supplied), you can refer to the following resolution information.
Specifications TV BROADCASTING PAL/SECAM B/G D/K K’ I/I’ L/L’ RECEIVING CHANNELS VHF (BAND I/III) UHF (BAND U) HYPERBAND MHEG-5 ENGINE compliant with ISO/IEC 13522-5 UK engine Profile 1 Object carousel support compliant with ISO/IEC 135818-6 and UK DTT profile for UK Frequency range: 474-850 MHz for UK models Digital Reception 170-862 MHz for EU models Transmission standard: DVB-T. MPEG-2 Demodulation: COFDM with 2K/8K FFT mode FEC: all DVB modes Video: MP@ML, PAL, 4:3/16:9 Audio: MPEG Layer I&II 32/44.
Important Instruction For your own safety read following instruction carefully before attempting to connect this unit to the mains supply.
50164710 Downloaded from www.Manualslib.