A700 Owner’s Handbook Picture Frame
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. IMPORTANT SAFETY INFORMATION Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a slightly damp cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
CONTENTS SAFETY INFORMATION.................................................................................................2 INTRODUCTION............................................................................................................4 UNPACKING.................................................................................................................4 CONTROLS AND FUNCTIONS.........................................................................................5 REMOTE CONTROL HANDSET.....
IINTRODUCTION UNPACKING Your Digital Picture Frame (DPF) enables you to view digital pictures from either a memory card or from a USB drive. The DPF is compatible with the following card formats: SD™ (Secure Disk), MMC™(Multimedia Card), MS™ (Memory Stick) and SDHC (Secure Disk High Capacity). The Frame will also support a USB 2.0 or 1.1 drive.
CONTROLS AND FUNCTIONS 8 1. 2. 3. 4. 5. 6. 7. 8. 6 7 SD/MMC/MS Card Slot USB Socket 5V DC Input Socket ON/OFF Switch Navigation Keys* Detachable Stand 7” Display Screen Remote Control Sensor 5 4 3 2 1 *NAVIGATION KEYS 1. Play/Pause; Confirm/Enter; hold to enter main menu 2. Previous/Left button 3. Down button; Rotate photo while playing a slideshow 4. Next / Right button 5.
REMOTE HANDSET HANDSET KEYS AND FUNCTIONS 1 Press to set the player in and out of Standby. 2 Press to move the cursor upward. 3 Press to move the cursor leftward or select the previous picture. 4 MENU Press to return to the main menu. 5 Press to move the cursor downward. 6 Press to select the previous picture when viewing pictures Switch to the previous page in thumbnail mode. 7 Press to zoom the picture. 8 Press to select 4:3 or 16:9 aspect ratio for a picture 9 SETUP Press to go to the setup menu.
PLACEMENT Remove the stand from the clip at the rear of the frame GETTING STARTED HANDSET PREPARATION Remove the protective strip from the battery compartment to activate the battery. If the handset behaves erratically or fails to operate the battery should be replaced. 1: Press the catch at the side of the battery compartment. Slide out the battery cage 2: Remove the old battery. Place the new battery in the cage with the polarity as shown. Close the cage.
CONNECTING POWER If the DPF is being switched on for the first time, or after a default setting reset, you must first select a display language. ON buttons on Use the ( ) or ( ) buttons on the DPF or the the handset to make your selection. Press the button on the DPF or OK on the handset to confirm. OFF In the next screen, Use the ( ) or ( ) buttons on the DPF or the buttons on the handset to select YES or NO. Plug the DC power jack of the adapter into the DC socket in the DPF.
INSTALLING A USB DEVICE OR MEMORY CARD To insert a memory card. Position the card with the cropped corner facing the top of the screen and press gently in. To release a memory card. Grip both sides of the card and gently pull out. When first switched on the pictures will display as a Slide Show. Thereafter the display will depend on the setup you have customised. • If you switch on the DPF with a USB drive and a memory card inserted in the frame, the USB drive photos will be displayed.
• To go back one picture at a time: Press the key • To resume normal slideshow play: Press the OK key again. ZOOM AND PAN Press the key to cycle the picture size: → x2 → x4 → x8→x16 →Normal... Entering ZOOM mode automatically pauses the slideshow. When the Zoom is positive (i.e greater than 1) • Press the keys to pan the picture to left or right • Press the keys to pan the picture up or down • To resume slideshow play: cycle Zoom to Normal and press OK.
THUMBNAIL MODE You can enter thumbnail mode in two ways: During a Slideshow: Press the key NAVIGATING A SLIDESHOW VIA THE OSD MENU During a slideshow: Press the OSD key The OSD menu appears on the screen and slideshow pauses. Press the or key on the handset to navigate between the icons on the OSD menu. • To start the slide show from the current picture, highlight and press the OK key on the handset. • To skip to theprevious picture, highlight and press the OK key.
Accessing Thumbnail Mode from the Main Menu VIEWING THE CLOCK Switch the ON /OFF switch on the frame to ON. or Press the key to bring the frame out of standby Press MENU to display the main menu Press the or key on the handset to select a memory device. Switch the the frame to ON. or Press the key Press the or key toselect Clock. Press OK The Clock time/date will display. 23:37:06 20/08/10 Friday Press Press USB Card Clock Calendar Setup NOTE: The Time and Date should be set in the Setup Menu.
SYSTEM SETUP Access the Main Menu. Select SETUP: Press OK. (You can also enter the Setup Menu at by pressing the SETUP key on the handset) There are three Setup menus Press or to select the Photo Setup Menu. Press OK to enter the menu and display the menu contents. Main Menu USB Photo Setup Card Clock Calendar Setup Photo Setup Sliding show time 3s Photo Mode 5s Transition Effect 15 s Date Stamp 1 min Shuffle 15 min 1 hour Sliding show time The Sliding Show Time.
photo was originally taken - providing the date was correctly set up on the camera taking the original picture. Press OK to confirm and return to the Photo Setup Menu. Press or to select Shuffle. Press Press OK to confirm and return to the Photo Setup Menu. Press or to select Transition Effect.
CLOCK/CALENDAR SETUP Press or to select Clock/Calendar setup. Press OK Setting the Time The Default Time Format is for a 24 hour clock. Before setting the time you may wish to change the time format to 12 hour (AM/PM). Clock/Calendar Setup Press Press Show photo Off Clock/Calendar Setup Set time On Show photo 12hr Set time format Set time 24hr Set date Set time format Set date format Set date or or Set date format to select Show Photo. Press to select On or Off.
Setting the Language The language setting affects all the menus and selections in the DPF. Setting the Date The Default Date format is Month/Date/Year (mm/dd/yy). Before setting the date you may wish to change the format to dd/mm/yy.
Auto Run This setting selects the display which comes on when the DPF is switched on or brought out of Standby, Photo is the default. . Press or to select Power on/Power off. Press Press the keys to cycle Hour, Min and Frequency. Press or to change the values. You can set the On/Off time to operate once only, or daily. The default is OFF. If you set a Power ON time the frame wiill “Wake up” at the appointed time and then display the “Auto Run” option which you have selected. Press OK to confirm and return.
TROUBLESHOOTING AFTER USE If your DPF seems not to be working as well as you might expect, please work through this checklist before returning the product to Tesco. The DPF will not switch on. Switch off, Check the power supply connections, switch on again. The DPF will not recognise a memory card. Re-insert the card. You may need to reformat the card. The DPF will not play pictures on a card. The pictures must be in jpg form and smaller than 8000x8000 pixels. The handset is erratic.
CARE AND CLEANING Care and cleaning operations should be carried out with the unit unplugged from the mains. Clean the plastic parts with a barely damp cloth and then dry carefully. Do NOT touch the screen with bare fingers, hard or pointed objects. Clean the screen carefully with a special cloth, with a special optical cleaning cloth available from opticians and photography stores.. SPECIFICATIONS Power Supply: Power adaptor: Picture Format: USB Compliance: Memory Card: Weight: DC 5V DC 5V1.
Tesco Stores Ltd, Delamare Road, Cheshunt, Herts, EN8 9SL Technika Helpline: 0845 456 6767 (Calls cost up to 4p per minute from a BT landline, other providers may vary)
