Operating instructions

Playing back
English
(20)
English
(21)
20 21
Pitch control
(fine adjustment to pitch)

Speed selector button indicators of the
main unit during pitch control
1
Press [-] or [+] on the control unit
to make adjustment.
z
The pitch can be set within
approximately ±16% of the currently set
turntable speed [33/45/78].
z
The current set value appears on the
display of the control unit.
The display differs depending on the
display mode.
(Switching the display mode

21)
z
The turntable speed changes each time
the pitch is set while the turntable is
rotating.

To return to the prescribed turntable speed
Press [RESET] on the control unit.
The value immediately returns to the prescribed
turntable speed. (33
1
/
3
, 45 or 78.26 rpm)
* The display of the control unit shows the
prescribed setting.
The turntable speed becomes the prescribed
turntable speed in the turntable speed setting
mode and 0.0% in the pitch setting mode.

When the display mode is “Turntable
speed setting”

When the display mode is “Pitch setting”
＋ 0.1%
33
33
33.34
－ 0.1%
33
33
33.32
0.0%
33
33
33.33
＋ 16.0%
33
33
38.67
－ 16.0%
33
33
28.00
↑
↑
↑
・・
・・
・・
・・
↑
↑
↑
↑
[
＋
]
[
＋
]
[
ー ]
[
ー ]
[
＋
]
[
＋
]
[
ー ]
[
ー ]
The specified
turntable speed
The specified
turntable speed
The adjusted value
(turntable speed)
The adjusted value
(percentage)
(Initial setting)
* Pressing the button increases or decreases the
value.
* Holding the button down accelerates the increase
or decrease.
z
Blue LED on: Without pitch control (0.0%)
z
Orange LED on: During pitch control
z
The value to two
decimal places is
displayed.
z
The turntable speed
can be adjusted in
increments of ±0.01
turn.
z
The value to one
decimal place is
displayed.
z
The pitch can
be adjusted in
increments of ±0.1%.
0.0%
33
33.33
33
(Display mode: Turntable speed setting)
(Display mode: Pitch setting)
Note
z
The pitch can be set for each turntable
speed.
z
Turning off the power button cancels the
pitch control setting. Turning on the power
button again returns the value to the initial
setting.
START・STOP
33 45 78
Indicators
↑
The specified
turntable speed
The adjusted value
(turntable speed)

Operation during “Turntable speed
measurement”
Operating the buttons as below changes the
display mode to “Turntable speed setting”
allowing you to make the setting.
* The display mode returns to “Turntable
speed measurement” if no operation is
performed within three seconds.
· [-]/[+]: The pitch can be adjusted.
(

20)
· [RESET]: The value immediately returns to
the prescribed turntable speed.
· [33/45/78]: The turntable speed changes
each time the button is pressed.
Operation and display of the control unit
Switching the display mode
1
Press [DISPLAY] on the control
unit.
Each time [DISPLAY] is pressed, the display
mode changes in order of “turntable speed
setting”
→
“Pitch setting”
→
“Turntable
speed measurement”
→
“Turntable speed
setting”
→
...
0.0%
33
33.33 rpm
33
33.33 rpm
33
(33
1
/
3
turns)
(Turntable
speed setting)
(45
turns)
(Pitch setting)
(Stop state)
(During
rotation)
(Turntable
speed
measurement)
(

See below.)
(78
turns)
Turntable speed setting
1
Press [33/45/78] on the control
unit.
Each time [33/45/78] is pressed, the
turntable speed changes in order of “33”
→
“45”
→
“78”
→
“33”
→
...
z
The turntable speed changes each time
the pitch is set while the turntable is
rotating.
↑
↑
↑
↑
↑
↑
33.33
33
33.33
33
45.00
45
78.26
78
Note
z
An averaged value is displayed.
-- . -- rpm
33
Turntablespeedmeasurement
The actual turntable speed can be measured in
this display mode. Switch the display mode (see
above) to enter this mode.
z
“rpm” appears after the numerical value.
z
“--.-- rpm” appears when the turntable has
stopped.