Operation Manual

RQTV0168
Checking the DAB signal quality
To improve reception by adjusting the antenna while monitoring signal quality on the
display.
 Press [DAB MENU] to enter menu mode.
“SCAN FAILED” appears if no stations are memorized. If this occurs, adjust the
antenna and try Auto scanning or change the Auto scan frequency range.
 Within 10 seconds, press [ALBUM or ] to select
“SIGNAL QUALITY” and then press [ENTER].
 Press [ALBUM or ] to select the frequency.
To exit
Press [DAB MENU] again.
In order to enjoy the new stations after adjusting the antenna, it is necessary to
perform Auto scanning and update the station memory.
DAB
DAB
DAB
Note
Note
7
DAB (continued)
➡
Page 2 for the position of remote control buttons.
Frequency block Frequency
Reception quality
0 (poor) - 8 (excellent)
Changing the Auto scan frequency range
Only the frequencies currently used in the UK as of March 2007 on BAND III are Auto
scanned (“United Kingdom”, factory setting).
Select “ALL BAND III” when you want to store stations on other frequencies to
memory.
 Press [DAB MENU] to enter menu mode.
 Within 10 seconds, press [ALBUM or ] to select
“DAB SCAN MODE” and then press [ENTER].
 Within 10 seconds, press [ALBUM or ] to select “UNITED
KINGDOM” or “ALL BAND III” and then press [ENTER].
Auto scan begins automatically after the change has been made.
To exit
Press [DAB MENU] again.
When the “DAB SCAN MODE” is changed, the DAB preset channels are erased and if
the DAB play timer has been set the timer switches to off.
DAB
DAB
DAB
Note
ALL BAND III Frequency
Frequency
block
Frequency
(MHz)
Frequency
block
Frequency
(MHz)
5A 174.928 10N 210.096
5B 176.640 10B 211.648
5C 178.352 10C 213.360
5D 180.064 10D 215.072
6A 181.936 11A 216.928
6B 183.648 11N 217.088
6C 185.360 11B 218.640
6D 187.072 11C 220.352
7A 188.928 11D 222.064
7B 190.640 12A 223.936
7C 192.352 12N 224.096
7D 194.064 12B 225.648
8A 195.936 12C 227.360
8B 197.648 12D 229.072
8C 199.360 13A 230.784
8D 201.072 13B 232.496
9A 202.928 13C 234.208
9B 204.640 13D 235.776
9C 206.352 13E 237.488
9D 208.064 13F 239.200
10A 209.936
Shaded areas are frequencies used currently as of March 2007 in the “United
Kingdom”.
The remote control and main unit are factory-set to “REMOTE 1” mode.
If your remote control affects other equipment during operation, you can switch to
operate in “REMOTE 2” mode.
To switch to “REMOTE 2” mode
 (While pressing and hold [MUSIC PORT] on the main unit)
Press and hold [2] until “REMOTE 2” appears on the main unit display.
 Press and hold [ENTER] and [2] for at least 2 seconds.
The main unit and remote control are now set to operate in “REMOTE 2” mode.
To return to “REMOTE 1” mode
Perform steps 1 and 2 above but use [1] instead of [2] for both steps. (“REMOTE 1”
appears on the main unit during step 1.)
The remote control cannot work with the main unit if their modes are different.
“REMOTE 1” or “REMOTE 2” appears on the main unit when you operate the remote
control.*
* If “REMOTE 1” appears (The main unit is in “REMOTE 1” mode.)
Press and hold [ENTER] and [1] on the remote control for at least 2 seconds.
If “REMOTE 2” appears (The main unit is in “REMOTE 2” mode.)
Press and hold [ENTER] and [2] on the remote control for at least 2 seconds.
Changing the main unit and remote control mode
SC-EN35 DBEB.indd 7 28/03/2007 14:20:17