EN
Main Connections (For UK only) EN CAUTION: For UK Only CONNECT THE MAIN LEAD INTO AC MAINS POWER SOCKET POWER SUPPLY 230V. It must not be connected to D.C. mains. Note: The mains lead of the set is fitted with a moulded plug. If the mains socket are not compatible or if for any reason the plug is removed please follow the directions below. The moulded plug cannot be rewired and if removed must be disposed of safely.
Safety Information CAUTION! Invisible laser radiation when open. Avoid exposure to beam. Class 1 laser product. This system must be opened only by qualified technicians to prevent accidents caused by the laser beam. LASER λ = 780nm, P max=5 mW Rating Information : At the bottom of the unit. This unit complies with the existing requirements. In accordance with the rating plate of the unit, this unit current standards concerning electrical safety and electromagnetic compatibility.
Safety Information SPECIFICATIONS: EN TECHNICAL Power supply AC 230V ~50Hz Clock backup:9V 6F22 Power consumption: 7W Please respect the environment. Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling. Do not place the system near wet areas such as bathrooms and pool side. Do not expose this appliance to rain or moisture Avoid storing the system at humid places or near abnormally heated areas. Power is continuously supplied to the system.
Before you begin This clock radio is equipped with a memory holding system that can be powered with 9V battery (not included). The power failure protection circuit will not operate unless battery is installed. When normal household power is interrupted, or AC cord is unplugged, the battery will power the clock radio to keep track of time and alarm settings programmed into the memory.
Operating the Clock EN Setting time: 1. Press the SET button, the “ : “ will flash on the display . or FWD to set the time. 2. Press REV 4 Tip Tip: No icon will be flashing if all selectors are set, if you see any icon flashing on display, press the SET button repeatedly to confirm everything is set correctly.
Operating the Radio EN FM MW TUNING MW / FM Tuning the Stations Antennas 1. Press ON to turn on the radio. 2. Slide the MW/FM switch to the desired broadcast band. 3. Turn the TUNING knob to select a station. 4. Press OFF to turn off the radio. MW antenna - A built-in ferrite rod antenna eliminates the need for an outside antenna for MW reception. Rotating the unit slightly may improve the reception of distant MW stations.
Operating the CD player EN Listening to compact disc Selecting play mode 1. Lift to open the CD compartment door. 2. Insert a disc and close the door. 3. Press PLAY/PAUSE . 4. Adjust volume to your desired level. or FWD to skip back5. Press REV ward and forward. 6. Press STOP to stop CD playback. 1. Start CD playback. 2. During playback, press CD MODE to toggle between different play mode. When there is no disc in the CD compartment, “nd” will show on display. 6 - repeat the current track.
Operating the Alarm EN Setting the WAKE Time Waking by Selected Source Your digital clock operates on a 24 hour standard mechanism. You may be woken up by ALARM DIO or CD . 1. Press the SET button until ALARM 1 / ALARM 2 icon is blinking. or FWD to set the wake 2. Press REV time. The time decrements or increments will follow by a faster rate when you press or FWD . and hold either REV 3. After the ALARM time is set, press SET repeatedly until no icon is blinking. 1. Select an MW or FM station. 2.
Operating the Clock Radio EN Sleep Mode In sleep mode, the radio or CD will turn off automatically. Simply: 1. Listen to CD or radio. or 2. While holding SLEEP, press REV to set the sleep time. The time FWD range is from 1 minute to 2 hours. 3. Release SLEEP and the current time will be shown again. The radio or CD will turn off when the preset time elapses. If you decide to turn off the radio or CD sooner, press SNOOZE or OFF. 4.
Operating the Clock Radio Snooze Alarm Operation Seconds Time Display This operation allows extra sleep time after the alarm is on. The alarm will turn off by pressing SNOOZE until the snooze period is over. Snooze function can be used repeatedly up to 2 hours. After this, the alarm will turn off until the next alarm conditions are met. Set the “quiet” period as follow: The unit may display in seconds. 1. Press and hold SNOOZE. or FWD to set the 2.
