Optional Accessories External Microphone CP-2016-007 sold as a pair Bluetooth® Module CP-2016-004 Plugs into the Aura SoHo ™ Conference Phone Accessory Bay so you can use your cell phone to make conference calls. Digital Adapter Module CP-2016-003 Plugs into the Aura SoHo ™ Conference Phone Accessory Bay, so you can connect to your office digital PBX phone system. All Accessories are available from our website: www.spracht.com Accessory Bay © 2009 Spracht. All rights reserved.
SPRACHT AURA SOHO™ Conference Phone USER GUIDE
TABLE OF CONTENTS Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 Package Contents - -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 2 Aura SoHo™ Conference Phone Design - - - - - - - - - - - - - - - - 3 Wall Adapter Design - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 Safety Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5 Setup Tips - -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
Introduction Thank you for choosing the Aura SoHo™ Full Duplex Conference Phone, providing full featured, high performance conferencing for small office and home office environments. THE AURA SOHO™ CONFERENCE PHONE FEATURES: Full duplex communication- Now you can have simultaneous two way conversations. 360 coverage - Four built-in microphones provide 360 coverage so all participants can be heard clearly from anywhere in the room.
Package Contents 1. Aura SoHo™ Conference Phone 2. Wall Adapter 3. Phone Cable 4. Main Cable 5. 6’ Power Cord 6.
Aura SoHo™Conference Phone Design 1 2 3 8 4 7 6 5 BUTTONS LEDs 1. Power On/Off 2. Mic Mute - Red 3. Mute Microphone locations 4. Flash 5. Redial 6. Volume Up/Down B 7. Conference 8. Hold CONNECTORS A. Main Cable C A B. External Microphone Connector (for optional extra mics) B C.
Wall Adapter Main Cable Connector Phone Cable Connector For Wall Plug Back of Wall Adapter Mounting Holes 4
Safety Precautions The Aura SoHo™ Conference Phone is an electrical product. As with any electrical product, observe reasonable precautions to avoid risk of fire or electrical shock. • Do not use this product near water, such as near a sink or bath tub, or in a wet area, such as in a wet basement. Caution: This product is for indoor use only. • Do not use a telephone during an electrical storm; there is some risk of electrical shock from lightning.
Setup Setting up the Aura SoHo™ Conference Phone 1. Plug the power cord into the Wall Adapter. 2. Insert the power supply plug into an available electrical outlet. 3. Connect one end of the included phone cable into the Phone Connector port on on the Wall Adapter. 4. Connect the other end of the phone cable into a telephone phone jack located, for example, on the wall.
Setup Phone into a digital phone network or it may damage the unit. You will need a Digital Phone Adapter Module in order to use the Aura SoHo™ Conference Phone with a PBX, available for purchase on our website, www.spracht.com. 5. Connect one end of the included Main Cable into the Main Cable Connector port on on the Wall Adapter. IMPORTANT: Please use only the cable provided. The Main Cable is different from a network cable.
Setup for VoIP Analog Adapter boxes IMPORTANT NOTICE: The Aura SoHo™ Conference Phone has echo and noise cancellation which is optimized for ANALOG telephone lines (land lines). If you have a standard Analog phone line, the instructions on this sheet do not apply to you. Please proceed to page 10, Using the Aura SoHo™.
Setup 2. Confirm the Aura SoHo™ Conference Phone is connected properly by pressing the Power button �. The keypad back light will go on and you will hear a dial tone. Wait for 5 seconds, then press the Power button � again to turn OFF the unit. 3. Next, you will be changing the Aura SoHo™ Conference Phone setting to VoIP mode. The unit should be in On Hook state, which means no dial tone, and the keypad back light will be off. Press these keys on the keypad: 1, 0, 1.
Using the Aura SoHo™ Conference Phone TO MAKE A CALL Press the Power Button � to turn on the Aura SoHo™ Conference Phone, then enter the phone number for your call. ADJUST SPEAKER VOLUME Press the Volume Up ^ or Volume Down v button to adjust the speaker volume. ANSWER A CALL Press the Power Button � when the Aura SoHo™ Conference Phone rings. END CALL Press the Power Button � to end a call. REDIAL Press the REDIAL button to call the last number dialed.
MICROPHONE MUTE Press the MUTE button to turn off the microphones in the Aura SoHo™ Conference Phone. The red indicator light above the MUTE button will be on when muted. While in MUTE mode, you will be able to hear the other end of the call, but they will not hear you. Press the MUTE button again to resume speaking to the caller(s). The red light will go out. CONFERENCE NOW The patented ConferenceNow™ button allows for you to press one button to connect with the Conferencing Service.
Reprogram Conference Number The Aura SoHo™ Conference Phone comes preprogrammed with the number for Spracht’s conferencing service provider. If you decide to use this service, all you have to do is press the CONF button to make a conference call. The Conference Center’s number is the factory default. If you already have your own conferencing service, you will have to reprogram the CONF button to the number of your service if you want to make one touch conference calls.
in reprogram mode, press and hold the CONF button for 10 seconds. After 5 seconds, the backlight will come on; when the backlight starts flashing, you may release the CONF button. Enter the new Conference Center Phone Number. The maximum number of digits you can enter is 16, the minimum is 3. This number will be stored in memory. Press the HOLD button, and the number will be stored. The next time that you press the CONF button, the number you entered will be dialed automatically.
Flash Button Programming INSTRUCTIONS FOR REPROGRAMMING THE FLASH BUTTON FOR INTERNATIONAL USE Where the Aura SoHo™ Conference Phone is “based” outside of North America Changing the region code is not recommended for end users. This procedure is either completed in Manufacting prior to shipment, or best done by a Service Center or trained Technician. The Aura SoHo™ Conference Phone has a button labeled FLASH. This is used for three way conference calling.
INTERNATIONAL ONLY In Region Code programming mode, only the circled keys are active. Keypad Function Description FLASH button - Start the reprogramming process HOLD button - End the reprogramming process Number keys 1-9 - Region codes 1-9 Reprogramming Procedure 1. With the Aura SoHo™ Conference Phone in the On Hook state, meaning off, press the FLASH button and keep holding it down for 5 seconds. The keyboard backlight will come on and stay on.
SPECIFICATIONS Aura SoHo™ Conference Phone Order Information: Part Number CP-2016 Features Certifications: FCC part 68, UL, CE, VCCI, A-TICK, RoHS compliant Telephone connection: Analog PBX or standard analog PSTN line Digital PBX Modules: Available, support 100s of PBXs Microphone: 3 Noise cancelling 360° coverage, 44 dB ± 4 dB sensitivity, 200 Hz- 3.3 kHz Speaker/Amplifier: Output >95 dB at 5 watts, Bandwidth 200 Hz - 3.
Spracht Limited Warranty Policy All information is believed to be reliable, however specifications are subject to change without notice. Spracht warrants its products against defects or malfunctions in material and workmanship under normal use and service, with the exceptions stated below. This warranty lasts for one year from the original date of purchase. Coverage terminates if you sell or otherwise transfer the product.
FEDERAL COMMUNICATIONS COMMISSION STATEMENT Interference Statement This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0).
