MODEL RTA-TS200 ASSEMBLY INSTRUCTIONS Thank you for purchasing our product. REV.
RTA-TS200 P.1 • Please read carefully the assembly instructions before the installation. • Do not discard this manual or any of the packaging material until the unit has been completely assembled. • Might require two people. P.
RTA-TS200 P.2 P.
P.3 RTA-TS200 P.3 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. ❶ Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions. ❼ To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly. ❷ Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
RTA-TS200 P.4 P.4 ASSEMBLY STEPS STEP 1 Insert the Glide studs G into the bottom holes of the Legs 2. Hardware: 4 Pcs G 2 STEP 2 Assemble the Horizontal bar 3 in between the Legs 2 with screws A, making sure the center hole on the bar runs UP-DOWN. Hardware: A M6x45 2 2 Pcs Make sure the center hole runs UP-DOWN for step 4.
RTA-TS200 P.5 STEP 3 Hardware: C M6x12 5 Pcs P.5 • From behind the frame, assemble the Cross bars 4 to the Legs 2 with screws C. • Secure both Cross bars 4 in the center with screw C and Nut cap D. 1 Pc D D 2 2 C 4 4 The nut cap D is used only in the center STEP 4 Hardware: B M6x30 5 Pcs With the help of another person, place the tabletop 1 over the frame making sure the holes coincide, and secure it to the Legs 2 and the Horizontal bar 3 with screws B from underneath.
RTA-TS200 P.6 STEP 5 Hardware: B E F M6x30 ST4x12 Ø6x18 2 Pcs P.6 • Assemble the Top support bar 5 to the Tabletop 1 with screws B and washers F from underneath. • Assemble the Wire basket 12 to the Tabletop 1 with screws E from underneath. 5 4 Pcs 2 Pcs 1 F E 12 STEP 6 • Unfold the supports on the Tablet holder 8. Hardware: I M6x15 B 8 8 Pcs • Attach the Shelf supports 7 to the Monitor panels 6 with screws I.
RTA-TS200 P.7 STEP 7 You can now install the Monitor panels and the Tablet holder according to your preference: • Only one monitor shelf with the tablet holder on either side. • Both monitor shelves side to side. STEP 8 • Assemble the Cup holder 10 and the Headphones holder 11 to the underside of the tabletop 1 with screws H and according to your preference. You can install one on each side, or both on the same side. • Attach the CD holder 9 to either side of the Tabletop 1 by tightening its screw knob.
P.8 RTA-TS200 ALL DONE! Give yourself a nice pat on the back. You did a great job! P.
RTA-TS200 P.9 P.9 CARE, MAINTENANCE AND SAFETY WARNINGS: WEIGHT LIMITS 12.10 Lbs. (5.5 Kg) 12.10 Lbs. (5.5 Kg) 6.6 Lbs. (3 Kg) 6.6 Lbs. 132 Lbs. (3 Kg) (60 Kg) 12.10 Lbs. (5.5 Kg) 6.6 Lbs. (3 Kg) • Do not exceed the indicated weight limits. • Do not expose the surfaces to direct sunlight or to extreme environmental conditions. • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
P.10 RTA-TS200 P.10 TECHNI SPORT WARRANTY Gaming Chair: 2-YEAR WARRANTY Gaming Desk: 5-YEAR WARRANTY Gaming Chair Metal Frame: LIFETIME WARRANTY RTA Products, LLC has warranted the Techni Sport products to the original purchaser who acquired a new product from RTA Products or its authorized re-sellers of the product against defects in material or workmanship.
P.11 RTA-TS200 P.11 FOR SEVERAL HELP OPTIONS INCLUDING REPLACEMENT PARTS ORDERS _________________________________________________________________ VISIT: WWW.TECHNISPORTUSA.COM CLICK ON SUPPORT TAB Scan QR Code to order replacement parts OR EMAIL US: SUPPORT@TECHNISPORTUSA.
