MODEL RTA-S06 ASSEMBLY INSTRUCTIONS Thank you for purchasing our product. REV.
RTA-S06 P.1 • Please read carefully the assembly instructions before the installation. • Do not discard this manual or any of the packaging material until the unit has been completely assembled. • Might require two people. P.
RTA-S06 P.2 P.
RTA-S06 P.3 P.3 MAIN PARTS LIST 18 Top wood panel x1 19 Bottom drawer 21 Support tube x4 x1 front wheel 20 L bracket x1 and Nut 22 Top glass panel Ø1x2.
RTA-S06 P.4 P.4 ☛ This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware. Cam Lock Cam Bolt 3. Insert the cam lock on panel “B” making sure it goes aligned to receive the bolt’s head. 4. Turn the cam lock clockwise. This will lock the parts together and will close any gaps. Panel “B” 2. Join panel “B” to panel “A”.
P.5 RTA-S06 P.5 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. ❶ Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions. ❼ To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly. ❷ Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
RTA-S06 P.6 P.6 ASSEMBLY STEPS STEP 1 Attach the casters 3 to the bottom surface of panel 16 with screws E as indicated: • The locking casters 3L go at the FRONT of the panel. • The non-locking casters 3N go at the BACK. Hardware: E M4x14 16 Pcs NON-LOCKING go at the back 3N BOTTOM surface: 16 LOCKING go at the front 3L TOP surface: 16 16 (Fron STEP 2 Hardware: t) • Slide the metal fittings through the metal bar 23E in the following exact order: - One of 23A with the flat side UP.
RTA-S06 P.7 P.7 ASSEMBLY STEPS STEP 3 Assemble the locking system 23 to the right panel 15 by attaching the fittings 23A with screws C as shown. Hardware: C M3x15 8 Pcs (To p) (23E goes with rods at top) 23E 23C 15 (Front) STEP 4 Grab all the sets of sliders 12 (total 8 pcs) and separate them into 2 groups according to their shape: - The “Flat” ones will be used on the next step. - The “L Shaped” will be used until steps 17 and 24, set them aside.
RTA-S06 P.8 STEP 5 Hardware: C M3x15 8 Pcs P.8 Assemble the “Flat” sliders 12 to the side panels 14 and 15 with screws C. Please note: • The wheel is at the front, and faces down with 2 holes above it. • The sliders attach at the front on the 2nd hole. • The grooves on the panels are located at the back.
RTA-S06 P.9 STEP 7 P.9 Slide in the back panel 17 through the grooves of panels 14 and 15 and into the groove of panel 16. 17 15 14 16 STEP 8 • Attach bolts A to the bottom surface of the top wood panel 18. • Align cam locks on panels 14 and 15. • Assemble panel 18 to 14 and 15 as explained in page 4. Hardware: A M6x40 Bolt 4 Pcs 18 (Front) Cam locks alignment 15 14 STEP 9 Hardware: G Assemble the support tubes 21 to the discs on the top glass panel 22 with screws G.
RTA-S06 P.10 STEP 10 Assemble the support tubes 21 to the top wood panel 18 with screws H from underneath. Hardware: H M6x35 P.10 4 Pcs (Front) 21 18 C M3x15 4 Pcs Attach the metal fitting 23B to the drawers right panels 2 and 8 respectively with screws C. NOTE: The “U” on the fitting must face DOWN.
RTA-S06 P.11 STEP 12 Hardware: A M6x40 Bolt 4 Pcs For the top drawer, assemble side panels 1 and 2 to the front panel 4 with bolts A. P.11 STEP 13 Slide one of the bottom panels 5 through the grooves of the side panels and into the front panel as shown. 2 5 1 2 Cam locks alignment 1 4 STEP 14 Hardware: B M4x35 4 Pcs Assemble the back panel 6 to the side panels 1 and 2 with screws B. 4 STEP 15 Hardware: D M4x20 2 Pcs Assemble one of the handles 13 to front panel 4 with screws D.
RTA-S06 P.12 STEP 17 Hardware: C M3x15 4 Pcs P.12 Flip the drawer upside-down and assemble the “L” sliders 12 with screws C, making sure the wheel goes towards the back, and that they don’t protrude, otherwise, the drawer raises 1” and won’t fit in the cabinet.
RTA-S06 P.13 STEP 20 P.13 STEP 21 Slide the bottom panel 5 through the grooves of the side panels and into the front panel as shown. Hardware: B M4x35 4 Pcs Assemble the back panel 10 to the side panels 7 and 8 with screws B. 10 5 m) tto o (B p) (To 8 7 8 7 9 STEP 22 Insert the file tubes 11 through the corresponding hole on panel 10 and screw into panel 9, but DO NOT OVERTIGHTEN to avoid accidental damage humps or perforation. Holes to use for LETTER files (U.S.
P.14 RTA-S06 P.14 STEP 25 • Insert the drawers into the cabinet, starting with the bottom then the top. Insert at an angle with their fronts facing down, making sure the wheels from the drawer slide in the middle of the sliders inside the cabinet. If the top drawer does not enter, review the assembly done in steps 5, 17 and 24. • Test the lock on the top drawer: make sure the bottom drawer is completely closed and the rod on the lock is facing DOWN; the key must turn COUNTER-CLOCKWISE.
RTA-S06 P.15 P.15 CARE, MAINTENANCE AND SAFETY WARNINGS: WEIGHT LIMITS 30 Lbs. 22 Lbs. (13.6 Kg) (10 Kg) 22 Lbs. (10 Kg) 22 Lbs. (10 Kg) • Do not exceed the indicated weight limits. • Do not expose the surfaces to direct sunlight or to extreme environmental conditions. • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel. • Do not use solvents or abrasive materials to clean the unit.
P.6 RTA-S06 P.16 TECHNI MOBILI DESK WARRANTY DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. "Defects" as used in this warranty, is defined as any imperfections that impair the use of the furniture or product.
FOR SEVERAL HELP OPTIONS INCLUDING REPLACEMENT PARTS ORDERS _________________________________________________________________ VISIT: WWW.TECHNIMOBILI.COM CLICK ON SUPPORT TAB Scan QR Code to order replacement parts OR EMAIL US: SUPPORT@RTAPRODUCTS.
