MODEL RTA-8412L ASSEMBLY INSTRUCTIONS Thank you for purchasing our product REV.
RTA-8412L P.1 • Please read carefully the assembly instructions before the installation. • Do not discard this manual or any of the packaging material until the unit has been completely assembled. • Might require two people. P.
RTA-8412L P.2 A Main Tabletop x1 B Right Tabletop C Left Exterior panel D Left Interior panel F Right Exterior panel G Center-Left panel H Center-Right panel x1 E Right Interior panel x1 x1 x1 I Skirt panel for left cabinet P.
RTA-8412L P.3 P.3 MAIN PARTS LAYOUT (FOR REFERENCE) A B Q P D K E G L H S1 C F R T1 J I LIST OF HARDWARE, SCREWS AND FITTINGS PART QTY. ITEM 1 2Pcs 2 60Pcs Short Wooden Pin 3 16Sets Cam Lock & Bolt Sets 4 8Pcs ST5 x 8mm 5 8Pcs ST4.5 x 13mm 6 8Pcs ST3 x 16mm 7 20Pcs ST 3.5 x 16mm 8 10Pcs ST4 x 38mm Long Wooden Pin (Euro Screw) 13 1Pc Door Stopper 14 3Sets Handle U Shape (96mm) M3.
P.4 RTA-8412L P.4 ☛ This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware.
P.5 RTA-8412L P.5 %()25( <28 67$57 7+( $66(0%/< 3/($6( 5($' 7+( )2//2:,1* 7,36 $1' :$51,1*6 ❶ 'R D TXLFN LQYHQWRU\ WR PDNH VXUH WKH SDFNDJH FRQWDLQV DOO WKH SDUWV DQG KDUGZDUH OLVWHG LQ WKH DVVHPEO\ LQVWUXFWLRQV ❼ 7R DYRLG PLVDOLJQPHQWV DOZD\V OHDYH WKH VFUHZV ORRVH DQG WLJKWHQ WKHP XQWLO DOO SLHFHV DUH SRVLWLRQHG FRUUHFWO\ ❷ 0LVVLQJ GDPDJHG DQG GHIHFWLYH SDUWV FDQ EH UHSODFHG DW QR FRVW WR \RX 3OHDVH UHIHU WR WKH ODVW SDJHV RQ WKLV PDQXDO ❽ 'R QRW RYHUWLJKWHQ RU IRUFH WKH VFUHZV DV WKH\ PLJKW
RTA-8412L P.6 P.6 ASSEMBLY STEPS STEP 1 Hardware/Tools: 2 Short Dowel 60 Pcs Install the short dowels 2 into all panels as shown. Use a wooden or light rubber hammer to avoid damage to the pins. Please pay attention to the correct holes to use as other holes on the panels are intended for other hardware in other steps. DO NOT JOIN ANY PANELS, JUST INSTALL THE PINS.
RTA-8412L P.7 STEP 3 Hardware/Tools: 3 Bolt 7 ST3.5 x 16 Install bolts 3 into panels A, B, S1 and T1 in the holes indicated in the illustration. Please pay attention to the correct holes to use as other holes on the panels are intended for other hardware, and attach the metal plates 18 to panel B using screws 7 as shown. 16 Pcs 4 Pcs 3 7 2 Pcs 18 P.7 (NOT INCLUDED) 18 nt) (Fro nt) (Fro B A S1 ) T1 m) tto (Bo STEP 4 Hardware/Tools: 7 ST3.
RTA-8412L P.8 STEP 5 Hardware/Tools: P.8 For each set of slider 20, Separate the pieces according to their shape: - The Flat shaped will be used in the next step (2 pieces, both left and right). - The "L" shaped will be used until step 21 (2 pieces, left and right). Flat - Right 20 L - Shape - Right Flat - Left 2 Sets L - Shape - Left "L" Shaped Flat Shaped STEP 6 Hardware/Tools: 4 ST5 x 8 20 Install the flat shaped sliders 20 on panels E and F with screws 4 as shown.
RTA-8412L P.9 P.9 Assemble the panel H to panel Q using screw 9 as shown. STEP 7 Hardware/Tools: 9 ST5 x 40 2 Pcs (NOT INCLUDED) p) (To (Top) (Fro nt) Q ) ttom (Bo H STEP 8 Assemble the panel E to panel Q using screws 9 as shown. Hardware/Tools: 9 ST5 x 40 2 Pcs (NOT INCLUDED) This illustration shows the same parts from step 7, but viewed from a different angle (from the right).
RTA-8412L P.10 STEP 9 Hardware/Tools: 9 ST5 x 40 P.10 First assemble the panels L and N to panel E using screws 9, then join panels J to panel E by just pushing the dowels into the holes. 4 Pcs J L (NOT INCLUDED) N J E This illustration shows the same parts from step 8, but viewed from a different angle (from the left).
RTA-8412L P.11 P.11 Assemble the panel G to panel P using screw 9 as shown. STEP 11 Hardware/Tools: 9 ST5 x 40 2 Pcs (To (NOT INCLUDED) p) nt) (Fro P G STEP 12 Assemble the panel D to panel P using screw 9 as shown. Hardware/Tools: 9 ST5 x 40 2 Pcs This illustration shows the same parts from step 11, but viewed from a different angle (from the left).
RTA-8412L P.12 STEP 13 Hardware/Tools: 9 ST5 x 40 4 Pcs P.12 First assemble the panels K and M to panel D using screws 9, then join panels I to panel D by just pushing the dowels into the holes. K I (NOT INCLUDED) M I D This illustration shows the same parts from step 12, but viewed from a different angle (from the right).
RTA-8412L P.13 STEP 15 Hardware/Tools: 9 ST5 x 40 3 Pcs P.13 With the help of another person, bring the sections assembled in steps 10 and 14 upright and place them oriented as shown. Then assemble panel H to panel G using screws 9. Then slide the panel V through the grooves of C and D, and W through the grooves of E and F. Finally, install the metal pins 12 in the desired sets of holes on panels C and D, and place the panel O over the pins as shown.
RTA-8412L P.14 STEP 17 Hardware/Tools: 7 ST3.5 x 16 6 Pcs P.14 First make sure that the back edge of the tabletop B aligns with the edge of the tabletop A, then using screws 7, and from underneath the unit, attach: - The metal plate 18 from B to A. - The L Brackets 16 from P to A and from Q to B. 18 16 (NOT INCLUDED) 7 7 A B Q P STEP 18 Hardware/Tools: 6 ST3 x 16 17 From behind the unit, and using screws 6, install the corner brackets 17 on the positions shown in the illustration.
RTA-8412L P.15 STEP 19 Hardware/Tools: 6 Pcs 3 P.15 - Using cam locks 3, and as shown and explained in page 4, assemble: - The side panels S2 and S3 to front panel S1. - The side panels T2 and T3 to front panel T1. Then insert the bottom panels U into the grooves of the panels on each drawer as shown. (NOT INCLUDED) 3 U U T3 S2 S3 T2 S1 STEP 20 Hardware/Tools: 8 ST 4 x 38 T1 Assemble the drawers back panels S4 and T4 to their respective drawers using screws 8 as shown.
RTA-8412L P.16 STEP 21 Hardware/Tools: 8 Pcs 7 ST3.5 x 16 P.16 Place both drawers upside-down and assemble to their bottom the “L” shaped sliders using screws 7 as shown. Please note that the wheels go towards the back of the drawers and the sliders should not protrude from the bottom, otherwise the drawers raise 1” and will not fit in the unit. VERY IMPORTANT! 4 Pcs 20 7 CORRECT: Sliders don’t protrude.
RTA-8412L P.17 P.17 Install to the door R the Handle Set 14, and the Hinges 15 with screws 5 as shown. STEP 23 Hardware/Tools: 5 ST4.5 x 13 4 Pcs 1 Set 14 5 14 15 14 2 Pcs 15 R (NOT INCLUDED) Place both drawers into the right cabinet as shown, then assemble the door R to the left cabinet using screws 5, and adjust the alignment if necessary: Hardware/Tools: A: These screws adjust the vertical alignment. B: This screw adjusts the horizontal alignment. 4 C: This screw adjusts the depth.
RTA-8412L P.18 Cover all the screw heads with caps 11 as shown. STEP 25 Hardware/Tools: 11 19 Pcs 11 ALL DONE! Give yourself a nice pat on the back. You did a great job! P.
RTA-8412L P.19 P.19 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: WEIGHT LIMITS 110 Lbs (50Kg ) 110 Lbs (50Kg) 11 Lbs (5Kg) 11 Lbs (5Kg) 10 Lbs (4.5Kg) 11 Lbs (5Kg) 10 Lbs (4.5Kg) 11 Lbs (5Kg) • Do not exceed the indicated weight limits. • Do not expose the surfaces to direct sunlight or to extreme environmental conditions. • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
P.20 RTA-8412L P.
P.21 RTA-8412L P.
