MODEL RTA-482BC ASSEMBLY INSTRUCTIONS Thank you for purchasing our product. REV.
RTA-482BC P.1 • Please read carefully the assembly instructions before the installation. • Do not discard this manual or any of the packaging material until the unit has been completely assembled. • Might require two people. P.
RTA-482BC P.2 P.
RTA-482BC P.3 MAIN PARTS LAYOUT (FOR REFERENCE): LIST OF HARDWARE, SCREWS AND FITTINGS PART QTY ITEM A 18 M6x45 Bolt B 24 M6x40 Bolt C 8 M6x25 D 4 M6x30 E 4 ST3x15 F 24 ST4x16 G Sets 2 Anchor Kit 1 Allen Key 1 Screwdrive r P.
RTA-482BC P.4 P.4 ☛ This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing tthe assembly using this kind of hardware. Cam Lock Cam Bolt 3. Insert the cam lock on panel “B”, making sure it goes aligned to receive the bolt’s head. 4. Turn the cam lock clockwise. This will lock the parts together and will close any gaps. CORRECT Panel “B” Alignment: The cross points towards the panel with the bolt.
P.5 RTA-482BC P.5 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. ❶ Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions. ❼ To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly. ❷ Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
RTA-482BC P.8 P.8 ASSEMBLY STEPS STEP 1 Assemble the shelves 5 and 7 to the Upper left divider 6 with bolts A as shown and as explained in page 4. Hardware: A M6x45 Bolt 2 Pcs 6 5 7 Cam lock alignment STEP 2 Assemble the shelves 8 and 10 to the Middle divider 9 with bolts A as shown and as explained in page 4.
RTA-482BC P.9 STEP 4 Install the glide studs 3 into the bottom of the structures 1 and 2. Hardware: 1 4 Pcs 3 P.9 2 STEP 5 Hardware: B M6x40 Bolt 12 Pcs With the help of another person, assemble the Back structure 2 to all the panels assembled in step 7 with bolts B as shown and as explained in page 4.
RTA-482BC P.6 P.6 ASSEMBLY STEPS STEP 6 Assemble the Lower back panel 14 to the Lower panel 15 with bolts A as shown and as explained in page 4. Hardware: A M6x45 Bolt 2 Pcs 14 Cam locks alignment 15 STEP 7 Assemble the Lower side panels 11 and 12 to the Lower panel 15 with bolts A as shown and as explained in page 4.
RTA-482BC P.7 STEP 8 • Attach the piece 19B from the Door spring kit 19 to the lower shelf 13 with screws F, making sure the little stopper faces towards the front. Hardware: 19 A 2 Pcs 19 B 2 Pcs F ST4x16 P.7 13 F 4 Pcs 19B • Slide the spring piece 19A from the Door spring kit 19 through the piece 19B until it locks inside, making sure the spring button faces towards the front.
RTA-482BC P.10 STEP 10 P.10 With the help of another person, turn over the frame built in step 5 and place the box built in step 9 over the lower section of the structure 2. The side panels 11 and 12 will engage inside the frame, while the bottom panel 15 will stay on top of it as shown.
RTA-482BC P.10 STEP 10 P.10 With the help of another person, turn over the frame built in step 5 and place the box built in step 9 over the lower section of the structure 2. The side panels 11 and 12 will engage inside the frame, while the bottom panel 15 will stay on top of it as shown.
RTA-482BC P.11 STEP 12 Secure the side panels 11 and 12 to the structure 1 with screws C from the inside. Hardware: C M6x25 P.11 4 Pcs 1 12 11 Hardware: C M6x25 4 Pcs • With the help of another person bring the frame upright. • Secure the side panels 11 and 12 to the back structure 2 with screws C from the inside.
RTA-482BC P.12 STEP 14 Hardware: A D M6x45 Bolt M6x30 1 Pcs P.12 • Attach the remaining bolt A to the top panel 4 on the center hole. • Assemble panel 4 to the Upper left divider 6 as shown and as explained in page 4. • Secure panel 4 to structures 1 and 2 with screws D from underneath. 4 Pcs 4 A 2 1 6 STEP 15 Hardware: F 18 M6x45 8 Pcs 2 Pcs D • Attach the metal disk 19C from the Spring kit 19 to the doors 16 and 17 with the screws 19D. • Attach the Hinges 18 to the doors with screws F.
RTA-482BC P.13 STEP 16 Hardware: F ST4x16 16 Pcs P.13 • With the help of another person, install the Door 16 to the Lower left panel 11 by attaching the Hinges 18 with screws F only on the oval holes. • Install the Door 17 to the Lower right panel 12 by attaching the Hinges 18 with screws F only on the oval holes. 18 F 12 11 16 • If the doors are not closing properly or need alignment, proceed to do the following adjustments: A. Loosen these screws to adjust the height of the door. B.
RTA-482BC P.14 STEP 17 Hardware: G 1 Set 20 2 Pcs P.14 • Once you have selected the place against the wall where the unit will go, with the help of another person bring the unit closer to the wall, and calculate the 2 points on the wall where the anchor device G will be installed, which should be no more than 1 inch away from the top corners of the unit. • Mark the points on the wall and with the appropriate tools make a hole to install the anchors from the kit G.
P.15 RTA-482BC ALL DONE! Give yourself a nice pat on the back. You did a great job! IT IS EXTREMELY IMPORTANT THAT YOU READ ALL THE WARNINGS ON THE NEXT PAGE! P.
P.16 RTA-482BC P.16 TIP-OVER WARNING! Please keep your children and yourself safe. Tip-over accidents can result in serious injuries or be fatal to small children. PREVENT TIP-OVER ACCIDENTS BY FOLLOWING THESE RECOMMENDATIONS: 1. Secure the unit by anchoring it to the wall. The anchoring device has been provided with the unit, and must be installed by following the instructions shown in PAGE 14 of this manual. 2.
RTA-482BC P.17 P.17 CARE, MAINTENANCE AND SAFETY WARNINGS: WEIGHT LIMITS 66 Lbs. (30 Kg) 22 Lbs. (10 Kg) 22 Lbs. (10 Kg) 22 Lbs. (10 Kg) 22 Lbs. (10 Kg) 66 Lbs. (30 Kg) 22 Lbs. (10 Kg) • For the safety of small children and your own, secure the unit to the wall with the anchor device provided. • Do not exceed the indicated weight limits. • Always load the heavy objects on the lower shelves. • Do not allow small children to climb or play on the shelves or inside the lower cabinet.
P.18 RTA-482BC P.18 TECHNI MOBILI WARRANTY DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY TV Stand/Entertainment Center: 2 YEAR WARRANTY RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein.
P.19 RTA-482BC P.19 FOR SEVERAL HELP OPTIONS INCLUDING REPLACEMENT PARTS ORDERS _________________________________________________________________ VISIT: WWW.TECHNIMOBILI.COM CLICK ON SUPPORT TAB Scan QR Code to order replacement parts OR EMAIL US: SUPPORT@RTAPRODUCTS.
RTA-482BC P.11 STEP 12 Secure the side panels 11 and 12 to the structure 1 with screws C from the inside. Hardware: C M6x25 P.11 4 Pcs 1 12 11 Hardware: C M6x25 4 Pcs • With the help of another person bring the frame upright. • Secure the side panels 11 and 12 to the back structure 2 with screws C from the inside.
RTA-482BC P.12 STEP 14 Hardware: A D M6x45 Bolt M6x30 1 Pcs P.12 • Attach the remaining bolt A to the top panel 4 on the center hole. • Assemble panel 4 to the Upper left divider 6 as shown and as explained in page 4. • Secure panel 4 to structures 1 and 2 with screws D from underneath. 4 Pcs 4 A 2 1 6 STEP 15 Hardware: F 18 M6x45 8 Pcs 2 Pcs D • Attach the metal disk 19C from the Spring kit 19 to the doors 16 and 17 with the screws 19D. • Attach the Hinges 18 to the doors with screws F.
RTA-482BC P.13 STEP 16 Hardware: F ST4x16 16 Pcs P.13 • With the help of another person, install the Door 16 to the Lower left panel 11 by attaching the Hinges 18 with screws F only on the oval holes. • Install the Door 17 to the Lower right panel 12 by attaching the Hinges 18 with screws F only on the oval holes. 18 F 12 11 16 • If the doors are not closing properly or need alignment, proceed to do the following adjustments: A. Loosen these screws to adjust the height of the door. B.
RTA-482BC P.14 STEP 17 Hardware: G 1 Set 20 2 Pcs P.14 • Once you have selected the place against the wall where the unit will go, with the help of another person bring the unit closer to the wall, and calculate the 2 points on the wall where the anchor device G will be installed, which should be no more than 1 inch away from the top corners of the unit. • Mark the points on the wall and with the appropriate tools make a hole to install the anchors from the kit G.
P.15 RTA-482BC ALL DONE! Give yourself a nice pat on the back. You did a great job! IT IS EXTREMELY IMPORTANT THAT YOU READ ALL THE WARNINGS ON THE NEXT PAGE! P.
P.16 RTA-482BC P.16 TIP-OVER WARNING! Please keep your children and yourself safe. Tip-over accidents can result in serious injuries or be fatal to small children. PREVENT TIP-OVER ACCIDENTS BY FOLLOWING THESE RECOMMENDATIONS: 1. Secure the unit by anchoring it to the wall. The anchoring device has been provided with the unit, and must be installed by following the instructions shown in PAGE 14 of this manual. 2.
RTA-482BC P.17 P.17 CARE, MAINTENANCE AND SAFETY WARNINGS: WEIGHT LIMITS 66 Lbs. (30 Kg) 22 Lbs. (10 Kg) 22 Lbs. (10 Kg) 22 Lbs. (10 Kg) 22 Lbs. (10 Kg) 66 Lbs. (30 Kg) 22 Lbs. (10 Kg) • For the safety of small children and your own, secure the unit to the wall with the anchor device provided. • Do not exceed the indicated weight limits. • Always load the heavy objects on the lower shelves. • Do not allow small children to climb or play on the shelves or inside the lower cabinet.
P.19 RTA-482BC P.19 FOR SEVERAL HELP OPTIONS INCLUDING REPLACEMENT PARTS ORDERS _________________________________________________________________ VISIT: WWW.TECHNIMOBILI.COM CLICK ON SUPPORT TAB Scan QR Code to order replacement parts OR EMAIL US: SUPPORT@RTAPRODUCTS.
