MODEL RTA - 325 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference.
RTA-325 DIMENSIONS Product Size: 51-1/5"W x 22-1/4"D x 39-3/8"H MAXIMUM WEIGHT CAPACITIES DO NOT exceed this limit Please use care and good judgement when placing objects on wood surface
P.
P.
P.
P.7 Grab all the flat shaped Drawer Sliders (23) and set aside the “L” shaped ones. With the Left & Right Panels (7&8) oriented as illustrated, assemble one pair of flat sliders (23) to the top holes on their inside faces. The wheels will be located at the front and facing down. Screw the Bolts (B) to the corresponding holes on the inside face of Top Panel (11), then assemble the Top Panel (11) to the Left & Right Panels (7&8) by turning all the corresponding cam locks.
P.8 Screws the Bolts (B) to the corresponding holes on the inside face of Bottom Panel (10), then assemble the Bottom Panel (10) to (7), (8) & (9) by turning all the corresponding cam locks. Please pay close attention to the orientation of all the parts as illustrated. Assemble the other pair of flat sliders to the inside face of the Left & Right Side Panels (7&8). The wheels will be located at the front and facing down.
P.9 Use Screws (D) to assemble the Short Tube (5) and Long Tube (6) to the CPU Panel (4) with the plastic washers (M) in between the tubes and the panel. Then screw the Stud (3) to the short Tube (5). Please follow the illustration for the correct assembly order and orientation of the parts. Use Screws (E) to assemble the CPU Panel (4) to the Left Back Panel (1). Use Screws (F) to affix the CPU Tube (2) to the Left Back Panel (1) & CPU Panel (4).
P.10 Use Screws (G) to affix the Slider Bases (16) to the Main Panel (14). Use Screws (H) to fix the Keyboard Slider (15) to the Slider Bases (16) as illustrated. Please note the position of the tabs on the sliders. ATTENTION: A second person is required to assist with this step. First screw the Bolts (B) to the corresponding holes on the Main Table Top (14).
P.11 Use Screws (C) to assemble the Long Tube (6) to the Main Panel (14). Use Screw (I) to assemble the Short Support Tube (13) to the Top Panel (11). Use Screws (E) to assemble the Left Back Panel (1) to the Main Panel (14). Please refer to Page No. 6 for troubleshooting this step. Use Screws (C) to assemble the Keyboard Panel (17) to the Keyboard Slider (15).
P.12 Use Screw (K) to assemble the Top Support Tube (32) to the Top Glass (31). Use Screws (A) to affix the Metal Fittings (22) to the Left Back Panel (1). Insert the Top Glass (31) into the Metal Fittings (33), but do not tighten their screws yet. Then, place the plastic washer (N) in between the Top Tube (32) and the Main Panel (14), and use Screw (I) to affix the Top Tube. Finally, secure the Top Glass (31) by tightening the screws in the Metal Fittings (33), but be careful not to overtighten.
P.13 Assemble the Small Drawer Back Panel (22) between the Small Drawer Left & Right Panels (18&19) using Screws (L) as shown. Slide the Small Drawer Bottom Panel (21) thru the channels between panels (18) & (19) as shown. Make sure the panel fits inside all the channels. Left Place the small drawer upside-down. Grab the “L” shaped sliders (23) and assemble them to the drawer using Screws (A), with wheels facing towards the back of the drawer.
P.14 Assemble the File Drawer Back Panel (28) to the File Drawer Left & Right Panels (24&25) using Screws (L) as shown. Slide the File Drawer Bottom Panel (27) thru the channels between panels (24) & (25) as shown. Make sure the panel fits inside all the channels. Carefully insert the File Tubes (29) thru the Big Drawer Back Panel (28) and screw them into the insert of the Big Drawer Front Panel (26). WARNING: DO NOT OVERTIGHTEN the tubes as they may perforate and damage the front panel.
P.15 Carefully insert all the drawers starting from the bottom. Make sure the wheels from the drawers engage and roll in the middle of the sliders.
CARE AND MAINTENANCE English - DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT, OR TO EXTREME ENVIRONMENTAL CONDITIONS. EXPOSURE WILL DAMAGE THE PRODUCT, WHICH IS NOT COVERED BY THE WARRANTY. - CLEAN THE SURFACES PREFERABLE WITH A SOLUTION OF A SMOOTH SOAP AND WATER, THEN CLEAR WITH A DRY TOWEL. DO NOT USE SOLVENTS OVER STRUCTURAL TUBES. - BEFORE MOVING OR TRANSPORTING THE UNIT: *REMOVE ALL OBJECTS FROM THE TABLETOP, SHELVES, DRAWERS OR COMPARTMENTS THAT ARE HEAVY OR MIGHT FALL OFF.
