ASSEMBLY INSTRUCTIONS MODEL RTA - 2335 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference.
RTA-2335
RTA-2335 P.
RTA-2335 P.
RTA-2335 P.5 SCREWS LIST PART QTY. ITEM PART QTY.
P.
RTA-2335 P.7 ASSEMBLY STEPS: 1 20 20 19 19 23 18 SCREWS B 6X25 MM First screw bolts B to the Left & Right Drawer Front Panels (18 & 23), then assemble the Drawer Left & Right Panels (19 & 20) as explained in page 5. 4PCS 2 21 21 Slide in the Drawer Bottom Panel (21). 20 20 19 19 3 22 22 20 19 20 19 SCREWS Use screws D to assemble the Drawer Back Panels (22) to the Drawer Left and Right Panels (19 & 20).
RTA-2335 P.8 4 Insert the Studs (3) to the Main Structures (1). 1 3 X2 1 3 X2 5 Use screws C & H to assemble the Side Structures (4) and the Connect Tubes (5) to one of the Main Structures (1). 5 4 4 H C SCREWS C 6X25 MM 1 4PCS H 6X12 MM 4PCS 6 Use screws C & H to assemble the Side Structures (4) and the Connect Tubes (5) to the other Main Structure (1).
RTA-2335 P.9 7 5" 5" 9 12 8 11 SCREWS First screw bolts B to the Left & Right Top Panels (11 & 12), then assemble the Left & Right Support Panels (8 & 9) as explained in page 5. Please pay attention to the direction of panel 8 & 9. B 6X25 MM 4PCS ** There are 2 options to assemble our desk, please choose it according to your preference.
RTA-2335 A1 P.10 24 X2 13 I X2 14 I X2 SCREWS Use screws A to assemble the Hinges (24) to the Back Panel (13). Assemble screws I to the Back Panel (13) and Middle Support Panel (14) as shown. Please pay attention to the correct position of the parts on both panels. A 3X15 MM 4PCS I 4PCS A2 14 9 11 8 SCREWS 12 First screw bolts B to the other side of the Middle Support Panel (14) as shown, then assemble the Left & Right Top Panels (11 & 12) as explained in page 5.
RTA-2335 P.11 B1 24 X2 13 I X2 14 I X2 SCREWS A 3X15 MM Use screws A to assemble the Hinges (24) to the Back Panel (13). Assemble screws I to the Back Panel (13) and Middle Support Panel (14) as shown. Please pay attention to the correct position of the parts on both panels. 4PCS I 4PCS B2 14 9 8 11 12 SCREWS First screw bolts B to the other side of the Middle Support Panel (14) as shown, then assemble the Left & Right Top Panels (11 & 12) as explained in page 5.
RTA-2335 P.12 8 7 11 12 10 First screw bolts B to the Left and Right Panels (7 & 10), then assemble the Left and Right Panels (7 & 10) to the assembled part in step A3/B3 as explained in page 5. SCREWS B 6X25 MM 8PCS 9 17 Use screws G to assemble the Sliders (17) to the Left and Right Panels (7 & 10). 7 9 10 8 SCREWS 17 G 3X12 MM 17 8PCS 10 Use screws E to assemble the Bottom Panel (15).
RTA-2335 P.13 11 15 Use screws F to assemble the Bottom Panel (15) to the Main Structures (1). ATTENTION: To avoid misalignments, screw loose and do not tighten them until all are in place! 1 1 SCREWS F 6X40 MM 4PCS 12 16 J X8 12 11 First tear off the protective film of the Adhesive Foam Tapes (J), stick them to the Left and Right Top Panels (11 & 12) as shown, then carefully lay down the Glass Top (16). 13 17 2 X2 20 23 18 20 19 Insert the Grommets (2) to the Bottom Panel (15).
RTA-2335 P.14 14 25 24 X2 Use screws A to assemble the Long Top Panel (25) to the Hinges (24). SCREWS A 3X15 MM 4PCS If the door does not close properly, you can adjust its position by unscrewing loose the corresponding screws on the hinges: Adjusts the door horizontally Adjusts the door vertically Adjusts the door side-to-side when it is closed. When the optimal position has been reached, re-tighten the screws.
RTA-2335 P.15 15 27 26 Insert the Short Top Panel (26) and the Long Grommet (27).
CARE AND MAINTENANCE English - DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT OR EXTREME ENVIRONMENTAL CONDITIONS. ANY DAMAGE RESULTING FROM SUCH EXPOSURE IS NOT COVERED BY THE PRODUCT’S WARRANTY. - THE PREFERABLE METHOD TO CLEAN THE SURFACES IS TO WIPE THEM USING A SOFT CLOTH DAMPENED WITH A SOLUTION SOAP AND WATER, THEN DRY WITH A CLEAN TOWEL. - DO NOT SPRAY SOLVENTS OR CLEANING AGENTS DIRECTLY OVER THE SURFACES, STRUCTURAL TUBES OR METAL PARTS. - DO NOT LEAN, SEAT OR STAND OVER THE UNIT.
