MODEL RTA-7050 ASSEMBLY INSTRUCTIONS REQUIRES OF 2 PERSONS Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Do not discard this manual or the packaging material until the unit has been completely assembled.
RTA-7050 P.2 P.
RTA-7050 P.3 P.3 MAIN PARTS LAYOUT (for reference) ❶ ❸ ❼ ❸ ❷ ❺ ❹ ⓬ ⓮ ❾ ⓮ ❽ ❻ SCREWS LIST No. Figure Size qty. No. Figure Size Qty. M6x35mm 26 St3x14mm 16 ⌀8x30mm 34 ⌀25 (felt) 10 St7x58mm 16 ⌀22 (laminate) 8 St3.5x40mm 8 ☛ This unit uses special cam bolts and locks. The following explains how to assemble using this kind of hardware. This is not and assembly step, just a guide for when you have to use these kind of special hardware. Bolt 1.
P.4 RTA-7050 P.4 BEFORE STARTING THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNING: • Do a quick inventory to make sure the product contains all the parts and hardware. • Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card included with the product. • The replacement parts service is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
RTA-7050 P.5 P.5 STEPS 1 THROUGH 11 IS FOR THE ASSEMBLY OF THE LOWER SECTION Separate all the sliders pieces ⑲ according to their shape (no assembly is done here): - The “Flat” ones go on the side panels and will be used on step 2. - The “L” shaped go on the drawers and will be used until step 10, please set them aside. STEP 1 “L” shaped sliders: Will be used on step 10. “Flat” sliders: Will be used on step 2.
RTA-7050 P.6 STEP 4 Insert the back panel ⑬ thru the groves of panels ⑦, ⑨ and ⑩. STEP 5 1st: Insert the wooden pins Ⓑ in the corresponding holes on panels ⑨, ⑩, ⑪ and ⑫. 2nd: With the help of another person, place the bottom panel ⑧ and assemble it to panels ⑨, ⑩, ⑪ y ⑫ using screws Ⓒ as shown. Screws: 🅑 Φ8x30 8 Pcs 🅒 ST7x58 8 Pcs (The grove faces down and towards The back of the panel) ⓬ STEP 6 Φ25 (Felt) ⓫ Peel off and adhere the felt covers Ⓕ over the screw holes on panel ⑧ as shown.
P.7 P.7 RTA-7050 STEP 7 Assemble the drawer back panel ⑰ to the side panels ⑮ and ⑯ using screws Ⓓ as shown. Insert the drawer bottom panel ⑱ thru the groves of side panels ⑮, ⑯ and ⑰. Screws: 🅓 ST3.5x40 STEP 8 4 Pcs (The groves face down towards the bottom on all panels) (Front) (Front) STEP 9 1st Insert the bolts Ⓐ in the corresponding holes on the drawer front panel ⑭. 2nd: Insert and align the cam locks Ⓐ in the side panels ⑮ and ⑯.
P.8 RTA-7050 STEP 11 Insert the drawers in the unit. If they don’t seem to fit, review steps 2 and 10 for the correct assembly of the sliders. STEPS 12 THROUGH 18 FOR THE ASSEMBLY OF THE UPPER SECTION STEP 12 1st: Insert the wooden pins Ⓑ in the corresponding holes on panel ①. 2nd Insert the bolts Ⓐ in the corresponding holes on panel ①. 3rd: Insert and align the cam locks Ⓐ in the panels ③. 4th: Assemble the panels ③ to the panel ① as shown and as explained on page 3.
RTA-7050 P.9 STEP 13 1st: Insert the wooden pins Ⓑ in the corresponding holes on panel ②. 2nd: Insert the bolts Ⓐ in the corresponding holes on panel ⑤. 3rd: Insert and align the cam locks Ⓐ in panel ②. 4th: Assemble the panel ⑤ to panel ② as shown and as explained on page 3. Screws: M6x35mm 2 Pcs 🅐 🅑 Φ8x30 2 Pcs STEP 14 Screws: M6x35mm 2 Pcs 🅐 🅑 Φ8x30 P.
P.10 RTA-7050 STEP 15 Screws: M6x35mm 2 Pcs 🅐 🅑 Φ8x30 2 Pcs 🅒 ST7x58mm 4 Pcs 1st: Assemble the panel ② to the panels ③ using screws Ⓒ. 2nd: Insert the wooden pins Ⓑ in the corresponding holes on panel ①. 3rd: Insert the bolts Ⓐ in the corresponding holes on panel ①. 3th: Insert and align the cam locks Ⓐ in panel ④. 5th: Assemble panel ④ to panel ① as shown and as explained on page 3.
P.11 STEP 17 Place the following adhesive lables: - Felt Ⓕ for the screw holes on panel ⑥. - Laminate Ⓖ for the cam lock holes on panels ③, ④ and ⑤. Screws: 🅕 Φ25 (felt) P.11 RTA-7050 4 Pcs (Felt) 🅖 Φ22 (laminate) 8 Pcs STEP 18 CLOSED: (Laminate) Place the upper section assembled in step 17 over the lower section assembled in step 11 according to your preference. The below illustrations show some suggestions.
P.12 P.12 RTA-7050 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: WEIGHT LIMITS: 55 Lbs (25 Kg) expanded 88 Lbs (40 Kg) closed 44 Lbs (20 Kg) 88 Lbs (40 Kg) 44 Lbs (20 Kg) 11 Lbs (5 kg) 44 Lbs (20 Kg) 44 Lbs (20 Kg) 11 Lbs (5 Kg) MAXIMUM RECOMMENDED EXPANDED LENGTH: • When setting the unit in expanded option, do not place the upper section too close to the edge of the lower section. • Do not exceed the indicated weight limits.
