MODEL RTA-7050 ASSEMBLY INSTRUCTIONS Thank you for purchasing our product. REV.
RTA-7050 P.1 • Please read carefully the assembly instructions before the installation. • Do not discard this manual or any of the packaging material until the unit has been completely assembled. • Might require two people. P.
RTA-7050 P.2 P.
RTA-7050 P.3 P.3 LIST OF HARDWARE, SCREWS AND FITTINGS PART QTY ITEM PART QTY ITEM A 26 M6x35 E 16 ST3x14 B 34 ⌀8x30mm (wooden dowels) F 10 ⌀25 (felt) C 16 ST7x58 G 8 ⌀22 (laminate) D 8 ST3.
RTA-7050 P.4 P.4 ☛ This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware. Cam Bolt Cam Lock 1. Screw the bolt into the corresponding panel. 2. In the other panel, insert the cam lock and align it so it can properly receive the head of the bolt, then join the panels. There might be a very small gap between the panels which is normal.
P.5 RTA-7050 P.5 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. ❶ Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions. ❼ To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly. ❷ Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
RTA-7050 P.6 P.6 STEPS 1 THROUGH 11 IS FOR THE ASSEMBLY OF THE LOWER SECTION, WHICH WILL ASSEMBLE UPSIDE-DOWN STEP 1 Separate the sliders 19 according to their shape: - The “L” sliders (for the drawers) will be used until step 10, please set them aside. - The "flat" sliders (for inside the unit) are the ones being used in the next step. STEP 2 With the panels 9, 10, 11 and 12 oriented as shown, assemble the “Flat” sliders 19 on the bottom of the panels using screws E as shown.
RTA-7050 P.7 STEP 3 On the top panel 7 screw the bolts A into the outermost holes and insert the wooden dowels B in the innermost holes as shown. Hardware: A B M6x35 Φ8x30 P.
RTA-7050 P.8 STEP 6 Hardware: B C Φ8x30 ST7x58 8 Pcs P.8 First insert the dowels B in the innermost holes on panels 9, 10, 11 and 12, then with the help of another person place the bottom panel 8 and assemble it to the panels using screws C as shown. 8 Pcs C The groove on panel 8 go at the back of the panel. B 11 12 STEP 7 Peel off and adhere the felt covers F on panel 8 as shown. Then with the help of another person turn the unit it upright.
RTA-7050 P.9 STEP 9 P.9 Insert and align the cam locks A in the side panels 15 and 16. Then screw the bolts A into panel 14, and assemble this panel to panels 15 and 16 as shown and as explained on page 4. Hardware: 4 A Sets M6x35 Refer to page 4 p) (To (B a ck) STEP 10 Hardware: E ST3x14 4 Pcs Put the drawer upside-down, and assemble the “L” shaped sliders 19 using screws E as shown, making sure the wheel goes towards the back and the sliders don’t protrude at the bottom.
RTA-7050 P.10 P.10 STEPS 12 THROUGH 17 ARE FOR THE ASSEMBLY OF THE UPPER SECTION, WHICH WILL ALSO ASSEMBLE UPSIDE-DOWN STEP 12 Hardware: 4 A Sets M6x35 B Φ8x30 4 Pcs 1st: Insert the dowels B in the innermost holes on panel 1 on the center and right side. 2nd: Insert the bolts A in the outermost holes on panel 1. 3rd: Insert and align the cam locks A in the panels 3. 4th: Assemble the panels 3 to the panel 1 as shown and as explained on page 4.
RTA-7050 P.11 STEP 14 Hardware: 2 A Sets M6x35 B Φ8x30 P.11 1st: Insert the dowels B in the innermost holes on panels 1 and 3. 2nd: Insert the bolts A in the outermost holes on panel 1. 3rd: Insert and align the cam locks A in panel 5. 4th: Assemble the panel 2 to the panels 3, and the panel 5 to the panel 1 as shown and as explained in page 4. 6 Pcs Refer to page 4 STEP 15 Hardware: 2 A Sets 1st: Secure the panel 2 to the panels 3 with screws C.
RTA-7050 P.12 STEP 16 Insert the dowels B in the innermost holes on panels 4 and 5, then assemble panel 6 using screws C. Hardware: B C Φ8x30 ST7x58 4 Pcs 4 Pcs STEP 17 Hardware: F G Φ25 (felt) 4 Pcs Place the following adhesive stickers: Felt F on panel 6. Laminate G for the cam lock holes on panels 3, 4 and 5. 8 Pcs Φ22 (laminate) (Felt) (Laminate) P.
RTA-7050 P.13 P.13 ALL DONE! Give yourself a nice pat on the back. You did a great job! You can place the upper section over the lower section according to your preference. The below illustrations show some suggestions. WARNING: For safety, when setting the unit in expanded option, do not place the upper section too close to the edge on the lower section.
RTA-7050 P.14 P.14 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: WEIGHT LIMITS: A A C B C D D C = 55 Lbs. (25 Kg) expanded 88 Lbs. (40 Kg) closed B = 88 Lbs. (40 Kg) C = 44 Lbs. (20 Kg) C D = 11 Lbs. (5 Kg) MAXIMUM RECOMMENDED EXPANDED LENGTH: 82.5” (210 c m) • Do not exceed the indicated weight limits. • When setting the unit in expanded option, do not place the upper section too close to the edge on the lower section.
P.15 RTA-7050 P.15 TECHNI MOBILI WARRANTY DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY TV Stand/Entertainment Center: 2 YEAR WARRANTY RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein.
P.16 RTA-7050 P.16 FOR SEVERAL HELP OPTIONS INCLUDING REPLACEMENT PARTS ORDERS _________________________________________________________________ VISIT: WWW.TECHNIMOBILI.COM CLICK ON SUPPORT TAB Scan QR Code to order replacement parts OR EMAIL US: SUPPORT@RTAPRODUCTS.
