Technaxx® * User Manual WiFi Smart Alarm System Starter-Kit TX-84 WiFi Basis Station TX-91 PIR Detection Sensor TX-85 Door & Window Contact TX-86 Remote Control SOS Button TX-87 Alarm Siren TX-88 [ not enclosed in Kit TX-84] The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares that this device, to which this user manual belongs, complies with the essential requirements of the standards referred to the Directive RED 2014/53/EU. The Declaration of Conformity you find here: www.technaxx.
Table of Contents 1 Features .............................................................................................................................. 3 1.1 WiFi Basis Station TX-91...................................................................................................... 3 1.2 PIR Detection Sensor TX-85 ................................................................................................ 3 1.3 Door & Window Contact TX-86.....................................................
6 My Secure Pro APP........................................................................................................... 20 6.1 WiFi Basis Station Alarm .................................................................................................... 20 6.1.1 Select and set mode (Stay, Away, Custom & Disarm) ....................................................... 20 6.1.2 Setting of Detector & Siren ................................................................................................
1.3 Door & Window Contact TX-86 Sensor alam triggering at ~2.5cm distance communication between contact & basis station Push message at low battery level areas operations/day Built-in vadalism alarm Two-way Transimission distance ~200m open ~3 years battery life time at ~20 1.4 Remote Control SOS Button TX-87 SOS button for emergency calls with Push message stay at home, disarm, SOS 4 adjustments possible: activate, 1.
3.1 WiFi Basis Station TX-91 The Basis Station is the brain of your alarm system. It has to be connected to your WiFi network. About this way it can send you push notifications on your Smartphone. With the 868MHz transmission it is able to connect to the detectors, sensors, remotes and sirens. The technique allows spanning a transmission range up to ~200m open space (no interference). Figure 3-1 1 = Power indicator; 2 = Function key; 3 = Reset button 3.
1 Case vandal-proof switch 6 Battery (Type CR123A) 2 Pyroelectric infrared detector 7 Antenna 3 Sensitivity adjustment 8 WiFi module 4 LED adjustment 9 Wall vandal-proof switch (backside) 5 Motherboard PCB (Printed Circuit Board) 10 LED 3.3 Door & Window Contact TX-86 This Door Detector is wireless intrusion detector. When arming zone is intruded, the detector will output alarm signal via wireless module to upload to wireless alarm Basis Station, thus alarm is generated.
3.4 Remote Control SOS Button TX-87 With the Remote Control you can change the modus arm, disarm, stay at home or you can activate the siren by pressing SOS. It is for home use. To easily disarm your alarm system when you coming home or arming the alarm system when you leave (see Figure 3-4 below). 1 = Activate the alarm system (on the road) 2 = Home Mode (at home) 3 = Deaktivate the alarm system 4 = Manuel Alarm (emergency alarm) 3.
4 Product Mounting Before fix mounting insert batteries, configure the device first and try it out. See chapter 5. 4.1 WiFi Basis Station TX-91 Device is for indoor use only Screw installation: If you want to mount the device make sure there is a power socket nearby and the WiFi signal is good constantly. Step 1. Dig holes bracket position. according to Step 2. Insert a dowel (=expansion bolt) into the hole. Step 3. Fix bracket via screw. Step 4.
4.2 PIR Detection Sensor TX-85 Device is for indoor use only Warnings: Installation and debugging must be executed by professional staff. If you encounter device failure, please do not open and repair the device, you shall contact its after-sales department. Avoid installation under direct sunlight. Avoid installation in Avoid installation in places where the environment of rapid change in wind speed. temperature is too high.
Step 4. For corner mount, form a triangle with installation bracket and two walls. Fix it on wall with screws via the hole on installation bracket. Hang device on hanger on installation bracket. See Figure 4-5.
4.3 Door & Window Contact TX-86 Device is for indoor use only Warnings: Installation and debugging must be executed by professional staff. If you encounter device failure, please do not open and repair the device, you shall contact its after-sales department. Avoid installation in environment with large magnetic field around. Avoid installation in places with a large amount of metal objects. Be careful with direction of installation, and install the magnet on the rear side with arrow (back) of the sensor.
Step 3. Follow Figure 4-10, pre-drill two holes on fixed part of door/window frame, and pre-drill two holes on mobile part of door/window. Step 4. Face device rear cover with bolt, insert and fasten the screws to fix the front covers. Figure 4-10 2. Mounting by fixing with double-sided adhesive tape* (*included): Step 1. Paste adhesive at back of the device, see Figure 4-11. Step 2.
4.4 Alarm Siren TX-88 Device is for indoor use only Warnings: Installation and debugging must be executed by professional staff. If you encounter device failure, please do not open and repair the device, you shall contact its after-sales department. Avoid installation in environment with large magnetic field around. Avoid installation in places with a large amount of metal objects. Device only for indoor use. Mounting by fixing with screw: Step 1. Please open device package, follow Figure 4-13.
5 Start Use 5.1 WiFi Basis Station TX-91 Connect Power: Use the included power adapter and Micro USB cable to connect the Basis Station with the AC socket. Figure 5-1 Download the APP Search for My Secure Pro APP, then download and start the APP. Tips: Android user go to Google Play Store and search for My Secure Pro. Apple user goes to Apple Store and search for My Secure Pro. 5.1.1 Connect Basis Station TX-91 to WIFI and add detector and siren to the Basis Station Step 1.
Step 3. Input Basis Station name (4), click the icon of QR code (5), and scan the QR code on the back of the Basis Station. Username (6) and Password (7) are admin. Also enable subscribe for getting Push Notifications (8). Click “Next” (9) after it is successfully recognized, input WIFI password (10) (WiFi key of the router). See figure 5-4. STOP! Go on with Step 4. Step 4. (11) Long press the function key (No.2) of Basis Station for 6 seconds and the blue LED flashes slowly.
Step 6. To connect Detector & Siren with the Basis Station press function key of Basis Station to enter the matching mode. Blue LED starts flashing. Now insert the battery into the detector/siren you want to add. The Basis Station informs you with a beep that the detector/siren is connected with the Basis Station. Same way for other detectors and sirens. Matching mode will last for max. 120s or you turn it off by pressing function key of the Basis Station again. To add.
5.1.3 Clear Detector / Siren Matching Info If the detector needs to be used with new Basis Station or restored factory default, you can operate according to the following steps. Quickly press the tamperproof switch of the case for 5 times, clear the config info of the detector/siren, restore to the initial status. The indicator light will be normally on for 6s and then flash if it clears successfully. Tip: The operation above can be used to fix malfunctions. 5.1.
5.2 PIR Detection Sensor TX-85 1. Network: Before you can normally use PIR detector, you must match device with Basis Station. Connection with Basis Station: Activate the paring mode at the Basis Station with the function key and power on the detector. When red LED is blinking, dial the vandal-proof switch and indicator is flashing. Wait about 10 sekonds. If the red LED turns OFF, the matching is successful. If the indicator flashes for three times, the matching is failed.
5.3 TX-86 Door and Window Contact Before you can normally use Door/Window Contact you must match device with Basis Station. Connection with Basis Station: Activate the paring mode at the Basis Station with the function key and power on the detector. When red LED is blinking, dial vandal-proof switch and indicator is flashing. Wait about 10 seconds. If the red LED is OFF, the matching is successful. If the indicator flashes for three times, the matching is failed. You shall follow these steps and try again.
6 My Secure Pro APP On the main menu choose Alarm. After you have added the Basis Station TX-91 like in chapter 5.1.1 Connect the Basis Station TX-91 to WIFI and add detector and siren to the Basis Station you have the following options. 6.1 Basis Station Alarm 6.1.1 Select and set mode (Stay, Away, Custom & Disarm) Stay Away Custom Disarm Figure 6-1 When you are at home, press “Stay” than the alarm system is disarmed. A short beep of the Basis Station shows that the mode is activated/ changed.
Setting (Gear) Audio Setting (loudspeaker) Select for the different mode (Stay, Away, Custom and Disarm) which detector should be activated. Set the volume of the base station’s alarm tone. Set the volume of the base station beteween mute, silent or loud. Note: this setting does not affect the volume of the siren. Tip: The alarm tone (buzzer) of Basis Station and siren can temporarily deactivated by pressing on the function key of the Basis Station.
PIR Remote 6.1.3 Name: Set name of the device. Link Device: Select a device (camera or door phone). The live view of the selected device will be shown when you open the push notification. Enable Siren: When the PIR Sensor is triggered the siren will be activated. If you disable that function siren will not buzz or flash, when the device is triggered. Preview Link Device Video: Pressing this button shows you the live view of the selected device that was chosen under “Link Device”.
Tip: When you want to refresh the detector list or the mode, just swipe to the bottom. The following symbols can be shown in front of the device name: the battery status of that device is low. Need to change the battery (CR123A 3V). If the battery gets low you will receive a push notification. the device is offline. Reasons can be that the distance between Basis Station and detector/sensor is too big, there are interferences that interrupt the signal or battery is empty.
6.2 Event List See the push notifications in the event list that alarmed you of motion in your home (see Figure 6-5 below). Alarm Tamper alarm Intrusion Offline Device / Function Door contact, PIR motion detector, Siren: When the detector is removed from the wall or its bracket, or when the chassis is opened, the base station sends a push notification to the Smartphone. If you set under chapter 6.1.
Low battery status Emergency alarm Door contact, PIR sensor, Siren / Indicates that a battery change of the device is needed. SOS button of the remote was triggered. / If you set under chapter 6.1.2 for Link device a camera or a door phone you will get through pressing on the event to the live view of the selected device. 6.3 Local Files Under local flies you see manual taken snapshots and records of the camera or door phone you connected with the PIR sensor or the Door contact. See chapter 6.1.
7 Change batteries of devices The Basis Station will send you a Push message when the battery status of a device is low. You will see a low battery status notification in the event list of your Smartphone. On the main screen you will see a small battery sign next to the device. For TX-85, TX-86 and TX-88 it is necessary to use CR123A 3V batteries. Open the device with a flat cross-screwdriver and switch the old battery with the new one. Normally device should reconnect automatically.
9.2 PIR Detection Sensor TX-85 Transmission frequency / power / distance 868MHz / 10dBm / ~200m (open areas) ~12m / passive infrared Detection range / Method (not visible 6500 LUX illumination) Viewing angle horizontal 90° & vertical 70° Alarm prompt Red LED (LED can be set off) Sensitivity Two level (jumper cap) high or low Power input DC 3V/50mA Power supply 1x CR123A battery 3V Vandal-proof Case and Wall (H) ~2.1–2.
9.5 WiFi Alarm Siren TX-88 Transmission frequency / power / distance 868MHz / 10dBm / ~200m (open areas) Sound Intensity 85dB (within 1m distance) Power input batteries DC 12V/200mA Power supply 4x CR123A battery 3V Vandal-proof Case and Wall Working conditions –10°C ~ +50°C / < 95% RH Installation Wall mounting (indoor only) Weight & Dimensions 140g (without batteries) / (L) 11.3 x (W) 7.2 x (H) 3.0cm Important Safeguards and Warnings Do not expose the device to lampblack, steam or dust.
This product includes software developed by third parties, including software which is released under the GNU General Public License Version 2 (GPL v2). This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
patent must be licensed for everyone's free use or not licensed at all. and conditions for copying, distribution and modification follow. The precise terms TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
third parties or a failure of the program to operate with any other programs), even if such holder or other party has been advised of the possibility of such damages. END OF TERMS AND CONDITIONS HOW TO APPLY THESE TERMS TO YOUR NEW PROGRAMS (1) If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
