User Manual Midi Security Kit PRO FullHD 1080P TX‐51 Table of Contents 1 FEATURES AND SPECIFICATIONS .......................................................................................... 7 1.1 Overview ................................................................................................................................................. 7 1.2 Features ...........................................................................................................................................
3 INSTALLATION AND CONNECTIONS...................................................................................... 17 3.1 Check Unpacked DVR ........................................................................................................................ 17 3.2 About Front Panel and Rear Panel ................................................................................................... 17 3.3 HDD Installation .............................................................................
4.4 Right-Click Menu ................................................................................................................................. 28 4.4.1 Window Switch .................................................................................................................... 28 4.4.2 PTZ Control.......................................................................................................................... 28 4.4.3 Color ........................................................
.10.4 Storage ................................................................................................................................ 86 4.10.5 System ................................................................................................................................. 96 5 WEB OPERATION................................................................................................................... 108 5.1 Network Connection ........................................................
.11 Log out ................................................................................................................................................ 163 5.12 Un-install Web Control ...................................................................................................................... 163 6 PROFESSIONAL SURVEILLANCE SYSTEM ......................................................................... 164 7 FAQ .........................................................................
The DVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. This series product shall be transported, storage and used in the specified environments. 6. Accessories Be sure to use all the accessories recommended by manufacturer. Before installation, open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package. 7.
1 FEATURES AND SPECIFICATIONS 1.1 Overview This series product is an excellent digital monitor product designed for security field. It adopts embedded Linux OS to maintain reliable operation. It is easy to use and can realize surveillance function after some simple setups. It has various functions such as record, playback, monitor at the same time and can guarantee audio video synchronization. This series product has advanced technology and strong network data transmission function.
1.3 Specifications 1.3.1 Midi Security Kit PRO FullHD1080P TX-51 Parameters System Video Parameters Main Processor Industrial embedded micro controller OS Embedded LINUX Video Encode Standard H.
Parameters Record Alarm HDD Bidirectional Talk Input N/A Record Mode Schedule record/manual record/MD record/Alarm record Record Playback Max 4-channel playback Backup Mode HDD, burner, USB device, network backup Alarm Input N/A Alarm Output N/A HDD Port 1 SATA port，does not support eSATA port One Space Coomunication Port Others HDD 4T Network 1 RJ45 port, 100Mbps Ethernet port Communication N/A USB 2 USB ports Power DC12V Power Consuption ≤20W（With power adapeter, no HDD） Wo
2 Overview and Controls This section provides information about front panel and rear panel. When you install this series DVR for the first time, refer to this part first. 2.1 Front Panel There is no button on the front panel of the Smart Box. There is no need to introduce the front panel. 2.1.1 Midi Security Kit PRO FullHD1080P TX-51 The front panel is shown as below. See Figure 2-1. Figure 2-1 Refer to the following sheet for front panel button information.
2.2 Rear Panel 2.2.1 Midi Security Kit PRO FullHD1080P TX-51 The rear panel of Midi Security Kit Pro TX-51 is shown as below. See Figure 2-2. Refer to the following sheet for detailed information. Figure 2-2 SN Icon 1 2 VGA 3 4 VIDEO IN 5 6 7 Name Note GND Ground end VGA video output port VGA video output port. Output analog video signal. Can connect to the monitor to view ananlog video output. USB2.0 port Connect to USB storage device, mouse, burning DVD-ROM and etc.
2.3 Connection Sample 2.3.1 Midi Security Kit PRO FullHD1080P TX-51 Refer to the following sheet for detailed information. Figure 2‐8 2.4 Remote Control (for all 3 receivers the same) The remote control interface is shown as in Figure 2-9. Note: remote control is not our standard accessory and it is not included in the accessory bag.
Remote Contol Functions Serial Number Name Function 1 Power button Click it to boot up or shut down the device. 2 Address Click it to input device number, so that you can control it. 3 Forward Various forward speeds and normal speed playback. 4 Slow play Multiple slow play speeds or normal playback. 5 Next record In playback mode, playback the next video. 6 Previous record In playback mode, playback the previous video.
key go to the menu 13 Multiplewindow switch Switch between multiple-window and one-window. 14 Auxiliary key In 1-ch monitor mode: pop up assistant function：PTZ control and Video color. Switch the PTZ control menu in PTZ control interface. In motion detection interface, working with direction keys to complete setup. In text mode, click it to delete character. 15 0-9 number key Input password, channel or switch channel. Shift is the button to switch the input method. 2.
In input box, you can select input methods. Left click the corresponding button on the panel you can input numeral/English character (small/capitalized). Here ← stands for backspace button. ＿ stands for space button. In English input mode: _stands for input a backspace icon and ← stands for deleting the previous character. In numeral input mode: _ stands for clear and stands for deleting the previous numeral. ← When input special sign, you can click corresponding numeral in the front panel to input.
Right click mouse In real-time monitor mode, pops up shortcut menu: one-window, four-window, nine-window and sixteen-window, Pan/Tilt/Zoom, color setting, search, record, alarm input, alarm output, main menu. Among which, Pan/Tilt/Zoom and color setting applies for current selected channel. If you are in multiple-window mode, system automatically switches to the corresponding channel. Exit current menu without saving the modification.
3 Installation and Connections Note: All the installation and operations here should conform to your local electric safety rules. 3.1 Check Unpacked DVR When you receive the DVR from the forwarding agent check whether there is any visible damage. The protective materials used for the package of the DVR can protect most accidental clashes during transportation. Then you can open the box to check the accessories. Check the items in accordance with the list.
7. Put the cover in accordance with the clip and then place the upper cover back. 8. Secure the screws in the rear panel and the side panel. Important: You can connect the HDD data cable and the power cable first and then fix the HDD in the device. Pay attention to the front cover. It adopts the vertical sliding design. You need to push the clip first and then put down. Important: You can connect the HDD data cable and the power cable first and then fix the HDD in the device.
Keep connection lugs in well contact BT The signal line and shielded wire should be fixed firmly and in well connection. Avoid dry joint, lap welding and oxidation. BT 3.5.2 Connecting Video Output Video output includes a BNC(PAL/NTSC1.0VP-P ，75Ω）output ,a VGA output and HDMI output. System supports BNC, VGA and HDMI output at the same time.
The alarm output port should not be connected to high power load directly (It shall be less than 1A) to avoid high current which may result in relay damage. Use the co contactor to realize the connection between the alarm output port and the load. 3. How to connect PTZ decoder a. Ensure the decoder has the same grounding with DVR, otherwise you may not control the PTZ. Shielded twisted wire is recommended and the shielded layer is used to connect to the grounding. b. Avoid high voltage.
Length of close time 3ms max Longevity Mechanical 50×106 times (3Hz) Electrical 200×103 times (0.5Hz) Temperature -40 ~+70 3.8 Other Interfaces There are still other interfaces on the DVR, such as USB port.
4 Overview of Navigation and Controls 4.1 Boot up and Shutdown 4.1.1 Boot up Before the boot up, make sure: The rated input voltage matches the device power on-off button. Make sure the power wire connection is OK. Then click the power on-off button. Always use the stable current, if necessary UPS is a best alternative measure. Follow the steps listed below to boot up the device. Connect the device to the monitor and then connect a mouse. Connect power cable.
Tips: Check the box Startup button here, system goes to startup wizard again when it boots up the next time. Cancel the Startup button, system goes to the login interface directly when it boots up the next time. Figure 4‐1 Click Cancel button or Next Step button, system goes to login interface. See Figure 4-2. System consists of four accounts: Username: admin. Password: admin. (administrator, local and network) Username: 888888. Password: 888888. (administrator, local only) Username: 666666.
Click OK button, you can go to General interface. See Figure 4-3. For detailed information, refer to chapter 4.10.5.1. Figure 4-3 Click Next button, you can go to network interface. See Figure 4-4. For detailed information, refer to chapter 4.9.3. Figure 4-4 Click Next button, you can go to Schedule interface. See Figure 4-5. For detailed information, refer to chapter 4.10.4.1.1.
Figure 4-5 Click Finish button, system pops up a dialogue box. Click the OK button, the startup wizard is complete. See Figure 4-6. Figure 4-6 4.3 Manual Record 4.3.1 Live Viewing After you logged in, the system is in live viewing mode. You can see system date, time, channel name and window No. If you want to change system date and time, you can refer to general settings (Main Menu->Setting->System->General).
Tips Preview drag: If you want to change position of channel 1 and channel 2 when you are previewing, you can left click mouse in the channel 1 and then drag to channel 2, release mouse you can switch channel 1 and channel 2 positions. Use mouse middle button to control window split: You can use mouse middle button to switch window split amount. Preview Control The preview control function has the following features. Support preview playback.
There are two ways for you to zoom in. Drag the mouse to select a zone, you can view an interface show as Figure 4-9. Figure 4-9 Put the middle button at the centre of the zone you want to zoom in, and move the mouse, you can view an interface shown as in Figure 4-10. Figure 4-10 Right click mouse to cancel zoom and go back to the original interface. 3) Manual record function It is to backup the video of current channel to the USB device.
4.4 Right-Click Menu On the preview interface, right click mouse, you can view menu interface shown as in Figure 4-11. Tips After you go to the corresponding interface, right click mouse to go back to the upper-level. Figure 4-11 4.4.1 Window Switch System supports 1/4-window. You can select from the dropdown list. See Figure 4-12. Figure 4-12 4.4.2 PTZ Control The PTZ setup is shown as in See Figure 4-13. Note the commend name is grey once device does not support this function.
Figure 4‐13 In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See Figure 4-14. Make sure your protocol supports this function and you need to use mouse to control. Click this key, system goes back to the single screen mode. Drag the mouse in the screen to adjust section size. The dragged zone supports 4X to 16X speeds. It can realize PTZ automatically. The smaller zone you dragged, the higher the speed.
Icon Function Icon Function Preset Flip Tour Reset Pattern Aux Scan Aux on-off button Rotate Go to menu 4.4.2.1 PTZ Function Setup Click 4-16. , you can go to the following interface to set preset, tour, pattern, and scan. See Figure Figure 4‐16 Preset Setup In Figure 4-16, click preset button and use eight direction arrows to adjust camera to the proper position. The interface is shown as in Figure 4-17. Click Set button and then input preset number.
Figure 4‐17 Tour Setup In Figure 4-16, click tour button. Input tour value and preset No. Click Add preset button to add current preset to the tour. See Figure 4-18. Tips Repeat the above steps to add more presets to the tour. Click Del preset button to remove it from the tour. Note some protocols do not support delete preset function. Figure 4-18 Pattern Setup In Figure 4-16, click Pattern button and input pattern number. Click Begin button to start direction operation.
Figure 4‐19 Scan Setup In Figure 4-16, click Scan button. Use direction buttons to set camera left limit and then click Left button. Use direction buttons to set camera right limit and then click Right button. Now the scan setup process is complete. Figure 4‐20 4.4.2.2 Call PTZ Function Call Preset In Figure 4-15, input preset value and then click call. to call a preset. Click again to stop Call Pattern In Figure 4-15, input pattern value and then click stop call. to call a pattern.
In Figure 4-15, input Scan value and then click call. to call a tour. Click again to stop Rotate In Figure 4-15, click to enable the camera to rotate. System supports preset, tour, pattern, scan, rotate, light and etc function. Note: Preset, tour and pattern all need the value to be the control parameters. You can define it as you require. You need to refer to your camera user’s manual for Aux definition. In some cases, it can be used for special process.
Refer to the following sheet for detailed information. Item Note Period There are two periods in one day. You can set different sharpness, brightness, and contrast setup for different periods. Effective Time Check the box here to enable this function and then set period time. Sharpness Brightness The value here is to adjust the edge of the video. The value ranges from 0 to 100. The larger the value is, the clear the edge is and vice versa. Note there is noise if the value here is too high.
Item Note Position It is to adjust the image position on the screen. Customized Click it to set customized color mode. 4.4.4 Search Refer to chapter 4.8.1 for detailed information. 4.4.5 Manual Record Refer to chapter 4.10.4.3.1 for detailed information. 4.5 Navigation Bar You need to go to the Main menu->Setting->System->General to enable navigation bar function; otherwise you can not see the following interface. The navigation bar is shown as below. See Figure 4-23. Figure 4-23 4.5.
4.5.6 Color Click button , system goes to the color interface. refer to chapter 4.4.3. 4.5.7 Search Click button , system goes to search interface. Refer to chapter 4.8.1 4.5.8 Alarm Status Click button , system goes to alarm status interface. It is to view device status and channel status. Refer to chapter 4.10.3. 4.5.9 Channel Info Click button , system goes to the channel information setup interface. It is to view information of the corresponding channel. See Figure 4-25. Figure 4‐25 4.5.
4.5.13 USB Manager Click ， system goes to the USB Manager interface. It is to view USB information, backup and update. Refer to chapter 4.8.2, chapter 4.9.4, chapter 4.10.5.7, and chapter 4.10.5.9 for detailed information. 4.6 USB Device Auto Pop-up After you inserted the USB device, system can auto detect it and pop up the following dialogue box. It allows you to conveniently backup file, log, configuration or update system. See Figure 4-26. Refer to chapter 4.8.2, chapter 4.9.4, chapter 4.10.5.
Figure 4-28 Refer to the following sheet for more information. SN Name Function 1 Display window Here is to display the searched picture or file. Support 1/4/8-window playback. 2 Search type 3 Calendar 4 Playback mode and channel selection pane. 5 Card number search Here you can select to search the picture or the recorded file. You can select to play from the read-write HDD, from peripheral device or from redundancy HDD.
6 7 Mark file list button File list switch button Click it to go to mark file list interface. You can view all mark information of current channel by time. Refer to chapter 4.8.1.3 for detailed information. Note only the product of this icon supports mark function. Double click it, you can view the picture/record file list of current day. The file list is to display the first channel of the record file. The system can display max 128 files in one time. Use the │and │ or the mouse to view the file.
play 1,fast play 2 and etc. Note: The actual play speed has relationship with the software version. Smart search The volume of the playback Click the snapshot button in the full-screen mode, the system can snapshot 1 picture. System supports custom snap picture saved path. Connect the peripheral device first, click snap button on the full-screen mode, you can select or create path. Click Start button, the snapshot picture can be saved to the specified path. Mark button.
After you set, you can click Clip button again to edit the second period. You can see the slide bar restore its previous position. Click Backup button after clip, you can save current contents in a new file. You can clip for one channel or multiple-channel. The multiple-channel click operation is similar with the one-channel operation. Note: 13 Record type System max supports 1024 files backup at the same time.
Figure 4‐29 Click the , you can go to the smart search playback. Click it again, system stops smart search playback. Important System does not support motion detect zone setup during the full-screen mode. During the multiple-channel playback, system stops playback of rest channels if you implement one-channel smart search. 4.8.1.2 Accurate playback by time Select records from one day, click the list, you can go to the file list interface.
Figure 4‐30 4.8.1.3 Mark Playback Make sure your purchased device support this function. You can use this function only if you can see the mark playback icon on the Search interface (Figure 4-28). When you are playback record, you can mark the record when there is important information. After playback, you can use time or the mark key words to search corresponding record and then play. It is very easy for you to get the important video information.
Figure 4-32 Modify Double click one mark information item, you can see system pops up a dialogue box for you to change mark information. You can only change mark name here. Delete Here you can check the mark information item you want to delete and then click Delete button, you can remove one mark item. . Note After you go to the mark management interface, system needs to pause current playback. System resume playback after you exit mark management interface.
Figure 4‐33 Select backup device and then set channel, file start time and end time. Click add button, system begins search. All matched files are listed below. System automatically calculates the capacity needed and remained. See Figure 4-35. Figure 4‐34 System only backup files with a √ before channel name. You can use Fn or cancel button to delete √ after file serial number. Click Start button, system begins copy. At the same time, the backup button becomes stop button.
Figure 4‐35 When the system completes backup, you can see a dialogue box prompting successful backup. File format: Click the file format; you can see there are two options: DAV/ASF. The file name format usually is: Channel number+Record type+Time. In the file name, the YDM format is Y+M+D+H+M+S. File extension name is .dav. Tips: During backup process, you can click ESC to exit current interface for other operation. The system will not terminate backup process.
For the user who does not have the shut down right, input corresponding password to shut down. Figure 4‐36 4.9 Information It is for you to view sysem info, event info, and network info and log info. 4.9.1 System Info Here is for you to view system information. There are total four items: HDD (hard disk information), record, BPS (data stream statistics), version. See Figure 4-37. Figure 4‐37 4.9.1.1 HDD Information Here is to list hard disk type, total space, free space, video start time and status.
Figure 4‐38 Double click one HDD information; you can see the HDD SMART information. See Figure 4-39. Figure 4‐39 4.9.1.2 Record Info It is to view record start time and end time. See Figure 4-40.
4.9.1.3 BPS Here is for you to view current video data stream (KB/s), resolution and etc. See Figure 4‐41. Figure 4‐41 4.9.1.4 Version Here is for you to view some version information such as version number, built date, serial number and etc. See Figure 4-42.
4.9.2 Event It is to display device status and channel status. See Figure 4-43. Figure 4‐43 4.9.3 Network 4.9.3.1 Online Users Here is for you to manage online users. See Figure 4-44. You can disconnect one user or block one user if you have proper system right. Max disconnection setup is 65535 seconds. System detects there is any newly added or deleted user in each five seconds and refresh the list automatically.
4.9.3.2 Network Load Network load is shown as in Figure 4-45. Here you can view the follow statistics of the device network adapter. Here you can view information of all connected network adapters. The connection status is shown as offline if connection is disconnected. Click one network adapter, you can view the flow statistics such as send rate and receive rate at the top panel. Figure 4‐45 4.9.3.3 Network Test Network test interface is shown as in Figure 4-46.
Figure 4‐46 4.9.4 Log Here is for you to view system log file. System lists the following information. See Figure 4-47. Log types include system operation, configuration operation, data management, alarm event, record operation, account manager, log clear, file operation and etc. It optimized reboot log. There are only three types: normal reboot, abnormal reboot and protection reboot. 0x02、0x03、 0x04 is included in the protection reboot type.
Select an item on the list and then click the Details button or double click the log item, you can view the detailed information such as log time, log type, log user, IP address and etc. See Figure 4-48. Figure 4‐48 4.10 Setting It is for you to set camera, network, event, storage, system and etc. 4.10.1 Camera Here you can set audio/video property, camera property and channel name, channel type. 4.10.1.
Delete: Select one device in the Added device list and then click Status: means connection is OK and means connection failed. Delete；Select a device on the Added device list, click Delete button, system disconnect device first and then remove its name from the list. Manual add: Click it to add the IPC manually. The port number is 37777. The default user name is admin and password is admin. to remove. Figure 4‐49 Click the Manual Add button; you can go to the following interface.
4.10.1.1.2 Channel Status Here you can view the IPC status of the corresponding channel such as motion detect, video loss, tampering, alarm and etc. See Figure 4-51. IPC status : : Front-end does not support. alarm event from current front-end. : Connection succeeded. : Connection failed. Connection status : Refresh: Click it to get latest front-end channel status. : Front-end supports. : There is Figure 4‐51 4.10.1.1.
4.10.1.1.4 Remote Upgrade It is to update the camera. From main menu->setting->camera->remote, the interface is shown as below. See Figure 4-53. Click Browse button and then select the upgrade file. Then select a channel (or you can select device type filter to select several devices at the same time.) Click Start upgrade button to update. You can see the corresponding dialogue once the upgrade is finish. Figure 4‐53 4.10.1.2 Camera For analog channel, the camera interface is shown as in Figure 4-54.
WDR: For the WDR scene, this function can lower the high bright section and enhance the brightness of the low bright section. So that you can view these two sections clearly at the same time. The value ranges from 1 to 100. When you switch the camera from no-WDR mode to the WDR mode, system may lose several seconds record video. HLC: After you enabled HLC function, the device can lower the brightness of the brightest section according to the HLC control level.
Figure 4‐55 4.10.1.3 Encode It is to set video bit stream, picture bit stream, video overlay parameter and etc. 4.10.1.3.1 Video Video setting includes the following items. See Figure 4-56. Channel: Select the channel you want. Type: Select from the dropdown list. There are three options: regular/motion detect/alarm. You can set the various encode parameters for different record types. Compression: System supports H.264 and MJPEG.
Figure 4‐56 4.10.1.3.2 Snapshot Here you can set snapshot mode, picture size, quality and frequency. See Figure 4-57. Snapshot mode: There are two modes: regular and trigger. If you set timing mode, you need to set snapshot frequency. If you set trigger snapshot, you need to set snapshot activation operation. Image size: Here you can set snapshot picture size. Image quality: Here you can set snapshot quality. The value ranges from 1 to 6.
4.10.1.3.3 Overlay Overlay interface is shown as in Figure 4-58. Cover area: Here is for you to set cover area. You can drag you mouse to set proper section size. In one channel video, system max supports 4 zones in one channel. Preview/monitor: privacy mask has two types. Preview and Monitor. Preview means the privacy mask zone can not be viewed by user when system is in preview status. Monitor means the privacy mask zone can not be view by the user when system is in monitor status.
4.10.1.3.4 Channel Name It is to modify channel name. It max supports 31-character. See Figure 4-60. Figure 4‐60 4.10.1.3.5 Channel Type It is to set channel type. It supports coaxial/UTP. See Figure 4-61. Figure 4‐61 4.10.2 Network 4.10.2.1 TCP/IP The interface is shown as in Figure 4-62 IP Version: There are two options: IPv4 and IPv6. Right now, system supports these two IP address format and you can access via them. MAC address: The host in the LAN can get a unique MAC address.
IP address: Here you can use up/down button () or input the corresponding number to input IP address. Then you can set the corresponding subnet mask the default gateway. Default gateway: Here you can input the default gateway. Note system needs to check the validity of all IPv6 addresses. The IP address and the default gateway shall be in the same IP section. That is to say, the specified length of the subnet prefix shall have the same string. DHCP: It is to auto search IP.
HTTPS port: Default value is 443. RTSP port: Default value is 554. Important: System needs to reboot after you changed and saved any setup of the above four ports. Make sure the port values here do not conflict. Figure 4‐63 4.10.2.3 WIFI The WIFI interface is shown as below. See Figure 4-64. Auto reconnecting WIFI: Check the box here, system automatically connects to the previous WIFI hotspot. Refresh: You can click it to search the hotspot list again.
WIFI working status: Here you can view current connection status. Note: After successful connection, you can see WIFI connection icon at the top right corner of the preview interface. When the hotspot verification type is WEP, system displays as AUTO since the device can not detect its encryption type. System does not support verification type WPA and WPA2. The display may become abnormal for the verification type and encryption type.
4.10.2.5 PPPoE PPPoE interface is shown as in Figure 4-66. Input “PPPoE name” and “PPPoE password” you get from your ISP (Internet service provider). Click save button, you need to restart to activate your configuration. After rebooting, DVR will connect to internet automatically. The IP in the PPPoE is the DVR dynamic value. You can access this IP to visit the unit. Figure 4‐66 4.10.2.6 DDNS Setup DDNS setup interface is shown as in Figure 4-67.
Figure 4‐67 Note NNDS type includes: CN99 DDNS, NO-IP DDNS, Dahua DDNS, Dyndns DDNS and sysdns DDNS. All the DDNS can be valid at the same time, you can select as you requirement. Private DDNS function shall work with special DDNS server and special Professional Surveillance Software (PSS). Dahua DDNS and Client-end Introduction 1) Background Introduction Device IP is not fixed if you use ADSL to login the network. The DDNS function allows you to access the DVR via the registered domain name.
User name: It is optional. You can input your commonly used email address. Important Do not register frequently. The interval between two registrations shall be more than 60 seconds. Too many registration requests may result in server attack. System may take back the domain name that is idle for one year. You can get a notification email before the cancel operation if your email address setup is OK. 4.10.2.7 IP Filter IP filter interface is shown as in Figure 4-68.
Figure 4‐68 Figure 4‐69 4.10.2.8 Email The email interface is shown as below. See Figure 4-70. SMTP server: Input your email SMTP server IP here. Port: Input corresponding port value here. User name: Input the user name to login the sender email box. Password: Input the corresponding password here. Sender: Input sender email box here. Title: Input email subject here. System support English character and Arabic number. Max 32-digit. Receiver: Input receiver email address here.
according to the interval you specified here. This function is very useful when there are too many emails activated by the abnormity events, which may result in heavy load for the email server. Figure 4‐70 4.10.2.9 FTP You need to download or buy FTP service tool (such as Ser-U FTP SERVER) to establish FTP service. Install Ser-U FTP SERVER first. From “start” -> “program” -> Serv-U FTP Server -> Serv-U Administrator. Now you can set user password and FTP folder.
Figure 4‐72 System also supports upload multiple DVRs to one FTP server. You can create multiple folders under this FTP. FTP interface is shown as in Figure 4-73. Highlight the icon in front of Enable to activate FTP function. Here you can input FTP server address, port and remote directory. When remote directory is null, system automatically create folders according to the IP, time and channel. User name and password is the account information for you to login the FTP. File length is upload file length.
4.10.2.10 UPnP The UPNP protocol is to establish a mapping relationship between the LAN and the WAN. Input the router IP address in the LAN in Figure 4-62. See Figure 4-74. UPNP on/off ：Turn on or off the UPNP function of the device. Status: When the UPNP is offline, it shows as “Unknown”. When the UPNP works it shows “Success” Router LAN IP: It is the router IP in the LAN. WAN IP: It is the router IP in the WAN.
Figure 4‐75 4.10.2.11 SNMP SNMP is an abbreviation of Simple Network Management Protocol. It provides the basic network management frame of the network management system. The SNMP widely used in many environments. It is used in many network device, software and system. You can set in the following interface. See Figure 4-76. Figure 4‐76 Enable the SNMP function. Use the corresponding software tool (MIB Builder and MG-SOFT MIB Browser.
Input the device IP you want to manage in the MG-SOFT MIB Browser. Set the corresponding version for your future reference. Open the tree list on the MG-SOFT MIB Browser; you can get the device configuration. Here you can see the device has how many video channels, audio channels, application version and etc. Note Port conflict occurs when SNMP port and Trap port are the same. 4.10.2.12 Multicast Multicast setup interface is shown as in Figure 4-77.
Administrative scoped addressees -239.0.0.0-239.255.255.255 -Private address space Like the single broadcast address of RFC1918 Can not be used in Internet transmission Used for multiple cast broadcast in limited space. Except the above mentioned addresses of special meaning, you can use other addresses. For example: Multiple cast IP: 235.8.8.36 Multiple cast PORT: 3666. After you logged in the Web, the Web can automatically get multiple cast address and add it to the multiple cast groups.
2) The proxy server software developed from the SDK. Open the software and input the global setup. Make sure the auto connection port here is the same as the port you set in the previous step. 3) Now you can add device. Do not input default port number such as the TCP port in the mapping port number. The device ID here shall be the same with the ID you input in Figure 4-78. Click Add button to complete the setup. 4) Now you can boot up the proxy server.
4.10.3 Event 4.10.3.1 Detect In the main menu, from Setting->Event->Detect, you can see motion detect interface. See Figure 4-81.There is three detection types: motion detection, video loss, tampering. The video loss has no detection region and sensitivity setup and tampering has no detection region setup. You can see motion detect icon if current channel has enabled motion detect alarm. You can drag you mouse to set motion detect region. Click OK button to save current region setup.
Alarm output: when an alarm occurs, system enables peripheral alarm devices. Latch: when motion detection complete, system auto delays detecting for a specified time. The value ranges from 1-300(Unit: second) Show message: System can pop up a message to alarm you in the local host screen if you enabled this function. Alarm upload: System can upload the alarm signal to the network (including alarm centre) if you enabled current function.
Figure 4‐82 Figure 4‐83 Figure 4‐84 Figure 4‐85 78
Motion detect here only has relationship with the sensitivity and region setup. It has no relationship with other setups. 4.10.3.1.2 Video Loss In Figure 4-81, select video loss from the type list. You can see the interface is shown as in Figure 4-86.This function allows you to be informed when video loss phenomenon occurred. You can enable alarm output channel and then enable show message function. Tips: You can enable preset/tour/pattern activation operation when video loss occurs. Refer to chapter 4.10.
Note: In Detect interface, copy/paste function is only valid for the same type, which means you can not copy a channel setup in video loss mode to tampering mode. About Default function. Since detection channel and detection type may not be the same, system can only restore default setup of current detect type. For example, if you click Default button at the tampering interface, you can only restore default tampering setup. It is null for other detect types.
Alarm in: Here is for you to select channel number. Type: normal open or normal close. PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go to preset, tour& pattern when there is an alarm. Click “select” button, you can see an interface is shown as in Figure 4-92. Period: Click set button, you can see an interface is shown as in Figure 4-93. There are two ways for you to set periods. There are max 6 periods in one day.
Figure 4-88 Figure 4‐89 .
Figure 4‐91 Figure 4‐92 Figure 4‐93 Figure 4‐94 83
4.10.3.3 Abnormality There are two types: HDD/Network. HDD: HDD error, no disk, no space. See Figure 4-95 and Figure 4-96. Network: Disconnection, IP conflict, MAC conflict. See Figure 4-97. Alarm output: Select alarm activation output port (multiple choices). Less than: System can alarm you when the HDD space is less than the threshold you set here (For HDD no space type only). Latch: Here you can set corresponding delaying time. The value ranges from 1s-300s.
Figure 4‐97 4.10.3.4 Alarm Output Here is for you to set proper alarm output such as schedule, manual. to select the corresponding alarm output. Highlight icon After all the setups click OK button, system goes back to the previous menu. See Figure 4-98.
4.10.4 Storage It is to set HDD management, storage parameters, set record plan and record control. 4.10.4.1 Schedule It is for you to set record plan and snapshot plan. 4.10.4.1.1 Record Note: You need to have proper rights to implement the following operations. Make sure the HDDs have been properly installed. After the system booted up, it is in default 24-hour regular mode. You can set record type and time in schedule interface.
Figure 4-101 Highlight icon to select the corresponding function. After completing all the setups click save button, system goes back to the previous menu. There are color bars for your reference. Green color stands for regular recording, yellow color stands for motion detection and red color stands for alarm recording. The white means the MD and alarm record is valid. Once you have set to record when the MD and alarm occurs, system will not record neither motion detect occurs nor the alarm occurs.
Figure 4-103 4.10.4.1.1.1 Quick Setup Copy function allows you to copy one channel setup to another. After setting in channel 1, click Copy button, you can go to interface Figure 4-104. You can see current channel name is grey such as channel 1. Now you can select the channel you wan to paste such as channel 5/6/7. If you wan to save current setup of channel 1 to all channels, you can click the first box “ALL”. Click the OK button to save current copy setup.
Note About redundancy setup: If current channel is not recording, current setup gets activated when the channel begin recording the next time. If current channel is recording now, current setup will get activated right away, the current file will be packet and form a file, then system begins recording as you have just set. After all the setups click save button, system goes back to the previous menu. Playback or search in the redundant disk.
Figure 4‐106 Figure 4‐107 4.10.4.1.2.2 Trigger Snapshot Follow the steps listed below to enable the activation snapshot function. After you enabled this function, system can snapshot when the corresponding alarm occurred. In main menu, from Setting->Camera->Encode->Snapshot interface, here you can input snapshot mode as trigger, size, quality and frequency. See Figure 4-108. In main menu, from Setting->Event->Detect, enable snapshot function for specified channels (Figure 4-109).
Figure 4‐108 Figure 4-109 4.10.4.1.2.3 Priority Note the activation snapshot has the higher priority than schedule snapshot. If you have enabled these two types at the same time, system can activate the activation snapshot when alarm occurs, and otherwise system just operates the schedule snapshot. 4.10.4.1.2.4 Image FTP In the main menu, from Setting->Network->FTP, you can set FTP server information. Enable FTP function and then click save button. See Figure 4-110. Boot up corresponding FTP server.
Input the corresponding information here, if you just upload the image FTP. Figure 4‐110 4.10.4.2 HDD Manager Here is for you to view and implement hard disk management. See Figure 4-111. You can see current HDD type, status, capacity and etc. The operation includes format HDD, and change HDD property (read and write/read-only/redundancy). Figure 4‐111 4.10.4.3 Record 4.10.4.3.1 Record Control Caution: You need to have proper rights to implement the following operations.
In live viewing mode, click record button in the front panel or record button in the remote control. System supports main stream and sub stream. There are three statuses: schedule/manual/stop. See Figure 4-112. Highlight icon “ ○ ” to select corresponding channel. Manual: The highest priority. After manual setup, all selected channels will begin ordinary recording.
Tips You can check All button after the corresponding status to enable/disable all-channel snapshot function. 4.10.4.4 HDD Detect The HDD detect function is to detect HDD current status so that you can clearly understand the HDD performance and replace the malfunction HDD. There are two detect types: Quick detect is to detect via the universal system files. System can quickly complete the HDD scan. If you want to use this function, make sure the HDD is in use now.
4.10.4.4.2 Detect Report After the detect operation, you can go to the detect report to view corresponding information. The detect report interface is shown as below. See Figure 4-116. Figure 4‐116 Click the item you can see the detailed information such as detect result. See Figure 4-117.
4.10.5 System 4.10.5.1 General 4.10.5.1.1 Device General setting includes the following items. See Figure 4-118. Device ID: Input a corresponding device name here. Device No: Here you can set device number. Language: System supports various languages: Chinese (simplified), Chinese (Traditional), English, Italian, Japanese, French, Spanish (All languages listed here are optional. Slight difference maybe found in various series.) Video standard: There are two formats: NTSC and PAL.
Figure 4‐119 4.10.5.1.3 Holiday Holiday setup interface is shown as in Figure 4-120. Click Add new holiday button, you can input new holiday information. See Figure 4-121. Here you can set holiday name, repeat mode and start/end time. Note When you enable Holiday settings and schedule setup at the same time, holiday setting has the priority. If the selected day is a holiday, then system records as you set in holiday setting. If it is not a holiday, system records as you set in Schedule interface.
Figure 4‐121 4.10.5.2 Display It is to set display, TV adjust, tour, zero-channel encode, and preview favorites information. 4.10.5.2.1 Display Display setup interface is shown as below. See Figure 4-122. Transparency: Here is for you to adjust transparency. The value ranges from 128 to 255. Channel name: Here is for you to modify channel name. System max support 25-digit (The value may vary due to different series). Note all your modification here only applies to DVR local end.
4.10.5.2.2 Tour Here you can activate tour function. Click Setup button, you can see an interface shown as in Figure 4-123 Enable tour: Highlight box here to enable this function. Interval: System supports 1/8-window tour. Input proper interval value here. The value ranges from 5-120 seconds. It is for schedule tour/alarm/motion detect tour. Split: You can select window split mode from the dropdown list. Channel group: It is to display all channel groups on current split mode.
can select interface zero-channel encoding mode at the right corner of the . Select a mode; you can view the local preview video. Figure 4‐124 4.10.5.2.4 Favorites It is for you to set and save favorites preview setup. You can select different window display modes and then select corresponding channel(s). Note for one mode, one channel can only be selected once. See Figure 4-125. Set channels: Click it you get channel setup information of current preview interface. For example.
Figure 4-126 4.10.5.3 PTZ The pan/tilt/zoom setup includes the following items. Select channel first. See Figure 4-127. PTZ type: There are two options: local/remote. Select remote if you are connecting to the network PTZ. See Figure 4‐128. Control mode: You can select control mode from the dropdown list. There are two options: Serial/HDCVI. For HDCVI series product, select HDCVI. The control signal is sent to the PTZ via the coaxial cable.
4.10.5.4 ATM/POS The ATM/POS function is for financial areas. It includes Sniffer, information analysis and title overlay function. The Sniffer mode is network. The network type interface is shown as below. See Figure 4-129. Here we take the ATM/POS protocol to continue. There are two types: with or without the protocol according to client’s requirements.
4.10.5.5 Account Here is for you to implement account management. See Figure 4-131 and Figure 4-132. Here you can: Add new user Modify user Add group Modify group Modify password. For account management note: For the user account name and the user group, the string max length is 6-byte. The backspace in front of or at the back of the string is invalid. There can be backspace in the middle. The string includes the valid character, letter, number, underline, subtraction sign, and dot.
Figure 4-132 4.10.5.5.1 Add/Modify Group Click add group button in Figure 4-132 , the interface is shown as below. See Figure 4-133. Here you can input group name and then input some memo information if necessary. There are total 98 rights such as control panel, shut down, real-time monitor, playback, record, record file backup, PTZ, user account, system information view, alarm input/output setup, system setup, log view, clear log, upgrade system, control device and etc.
Figure 4‐134 When you create a new user, you can input the corresponding MAC address of current user. If you leave this item in blank, any MAC address user can share this user account to login. Note system needs to check the validity of MAC. Only the 12-digit 0-f format address can pass the validity verification. System only saves small character even you input capitalized one. You can see the corresponding prompt if there is any illegal input. 4.10.5.
Format: Click Format button, system pops up a dialogue box for you to confirm current operation. System begins format process after you click the OK button. Note: System can not open config backup interface again if there is backup operation in the process. System refreshes device when you go to the config backup every time and set current directory as the root directory of the peripheral device.
4.10.5.9 Update Here is for you to view hardware features, software version, built date, release SN information and etc. You can also update system here. See Figure 4-138. Start: Insert the USB device that have the update file to the device and then click the Start button to begin the update. Important: Make sure the upgrade file name shall be update.bin.
5 WEB OPERATION Slightly difference may be found in the interface due to different series. 5.1 Network Connection Before web client operation, check the following items: Network connection is right DVR and PC network setup is right. Refer to network setup(main menu->Setting->Network) Use order ping ***.***.***.***(* DVR IP address) to check connection is OK or not. Usually the return TTL value should be less than 255.
5.3 LAN Mode For the LAN mode, after you logged in, you can see the main window. See Figure 5-3. Figure 5‐3 This main window can be divided into the following sections. Section 1: there are six function buttons: Live（chapter 5.4）, playback (chapter 5.9) setup (chapter 5.8), info (chapter 5.8.6), alarm (chapter 5.10), and logout (chapter 0). Section 2: There are channel number and one button: Start all. Start all button is to enable/disable all-channel real-time monitor.
Figure 5‐6 Section 4: Instant record button. Click it, the button becomes yellow and system begins manual record. See Figure 5-7. Click it again, system restores previous record mode. Figure 5‐7 Section 5: Local play button. The Web can playback the saved (Extension name is dav) files in the PC-end. Click local play button, system pops up the following interface for you to select local play file. See Figure 5-8.
1 2 3 4 Figure 5-9 On the top right corer, there are six unction buttons. See Figure 5-10. 1 2 3 4 5 Figure 5-10 1: Digital zoom: Click this button and then left drag the mouse in the zone to zoom in. right click mouse system restores original status. 2: Local record. When you click local record button, the system begins recording and this button becomes highlighted. You can go to system folder RecordDownload to view the recorded file. 3: Snapshot picture.
Parameter Function Pattern Aux Light wiper and Select Pattern from the dropdown list. You can input pattern value and then click Start button to begin PTZ movement such as zoom, focus, iris, direction and etc. Then you can click Add button to set one pattern. Input the corresponding aux value here. You can select one option and then click AUX on or AUX off button. You can turn on or turn off the light/wiper.
Figure 5-12 5.7 WAN Login In WAN mode, after you logged in, the interface is shown as below. See Figure 5-13. Figure 5‐13 Refer to the following contents for LAN and WAN login difference. 1) In the WAN mode, system opens the main stream of the first channel to monitor by default. The open/close button on the left pane is null. 2) You can select different channels and different monitor modes at the bottom of the interface. See Figure 5-14.
Figure 5‐14 Important The window display mode and the channel number are by default. For example, for the 16channel, the max window split mode is 16. 3) Multiple-channel monitor, system adopts extra stream to monitor by default. Double click one channel, system switches to single channel and system uses main stream to monitor. You can view there are two icons at the left top corner of the channel number for you reference. M stands for main stream. S stands for sub stream (extra stream).
Figure 5‐15 Figure 5‐16 Refer to the following sheet for log parameter information. Parameter Function Device search Click Device search button, you can view the searched device information on the list. It includes device IP address, port, device name, manufacturer and type. Add Select a device in the list and then click Add button, system can connect the device automatically and add it to the Added device list. Or you can double click one item in the list to add a device.
Parameter Function Manual Add Click it, the interface is shown as in Figure 5-16. Here you can add network camera manually. You can select a channel from the dropdown list (Here only shows disconnection channel.) Note: System supports manufactures such as Panasonic, Sony, Dynacolor, Samsung, AXIS, Arecont, Dahua and Onvif standard protocol. If you do not input IP address here. System uses default IP 192.168.0.0 and system does not connect to this IP. Can not add two devices at the same time.
Period It divides one day (24 hours) to two periods. You can set different hue, brightness, and contrast for different periods. Hue It is to adjust monitor video brightness and darkness level. The default value is 50. The bigger the value is, the large the contrast between the bright and dark section is and vice versa. Brightness It is to adjust monitor window brightness. The default value is 50. The larger the number is , the bright the video is.
Mode WDR For the WDR scene, this function can lower the high bright section and enhance the brightness of the low bright section. So that you can view these two sections clearly at the same time. The value ranges from 1 to 100. When you switch the camera from no-WDR mode to the WDR mode, system may lose several seconds record video. HLC After you enabled HLC function, the device can lower the brightness of the brightest section according to the HLC control level.
Figure 5‐19 Refer to the following sheet for detailed information. Parameter Function Channel Select a channel from the dropdown list. Video enable Check the box here to enable extra stream video. This item is enabled by default. Code stream type It includes main stream, motion stream and alarm stream. You can select different encode frame rates form different recorded events. System supports active control frame function (ACF). It allows you to record in different frame rates.
Audio source Select from the dropdown list. There are two options: Normal/HDCVI. In the normal mode, the audio signal comes from the Audio In. In the HDCVI mode, the audio signal comes from the coaxial cable of the camera. Watermark enable This function allows you to verify the video is tampered or not. Here you can select watermark bit stream, watermark mode and watermark character. Default character is DigitalCCTV. The max length is 85-digit.
Figure 5‐21 Refer to the following sheet for detailed information. Parameter Function Cover-area Check Preview or Monitor first. Click Set button, you can privacy mask the specified video in the preview or monitor video. System max supports 4 privacy mask zones. Time Title You can enable this function so that system overlays time information in video window. You can use the mouse to drag the time title position. You can view time title on the live video of the WEB or the playback video.
Figure 5‐23 5.8.2 Network 5.8.2.1 TCP/IP The TCP/IP interface is shown as in Figure 5-24. Figure 5‐24 Refer to the following sheet for detailed information. Parameter Function Mode There are two modes: static mode and the DHCP mode. The IP/submask/gateway are null when you select the DHCP mode to auto search the IP. If you select the static mode, you need to set the IP/submask/gateway manually. If you select the DHCP mode, you can view the IP/submask/gateway from the DHCP.
For the IP address of IPv6 version, default gateway, preferred DNS and alternate DNS, the input value shall be 128-digit. It shall not be left in blank. LAN load System can process the downloaded data first if you enable this function. The download speed is 1.5X or 2.0X of the normal speed. 5.8.2.2 P2P The P2P interface is shown as in Figure 5-25. You can scan the QR code to login the dveice in the WAN. Refer to P2P operation manual included in the resources CD for detailed information. Figure 5‐25 5.8.
5.8.2.4 WIFI Note this function is for the device of WIFI module. The WIFI interface is shown as in Figure 5-27. Figure 5‐27 Check the box to enable WIFI function and then click the Search SSID button. Now you can view all the wireless network information in the following list. Double click a name to connect to it. Click Refresh button, you can view latest connection status. 5.8.2.5 3G 5.8.2.5.1 CDMA/GPRS The CDMA/GPRS interface is shown as in Figure 5-28.
you close the extra stream monitor. Pulse interval here is for extra stream only. This item is null if you are using main stream to monitor. 5.8.2.5.2 Mobile The mobile setup interface is shown as in Figure 5-29. Here you can activate (send out “on”) or turn off (Send out “off”) the 3G connected phone or mobile phone, or the phone you set to get alarm message. Check send SMS box and then input the phone number in the receiver column. Click to add one receiver.
The DDNS is to set to connect the various servers so that you can access the system via the server. Go to the corresponding service website to apply a domain name and then access the system via the domain. It works even your IP address has changed. Select DDNS from the dropdown list (Multiple choices). Before you use this function, make sure your purchased device support current function. Figure 5‐31 Refer to the following sheet for detailed information.
default domain name (Generated by MAC address) for your option. You can also use customized valid domain name (has not registered.). 3) Operation Before you use Dahua DDNS, you need to enable this service and set proper server address, port value and domain name. Server address：www.dahuaddns.com Port number：80 Domain name：There are two modes: Default domain name and customized domain name.
Figure 5‐33 Refer to the following sheet for detailed information. Parameter Function Enable Check the box here to enable email function. SMTP Server Input server address and then enable this function. Port Default value is 25. You can modify it if necessary. Anonymity For the server supports the anonymity function. You can auto login anonymously. You do not need to input the user name. Password and the sender information. User Name The user name of the sender email account.
Parameter Update (interval) Email test Function period This function allows the system to send out the test email to check the connection is OK or not. Check the box to enable this function and then set the corresponding interval. System can send out the email regularly as you set here. The system will automatically sent out a email once to test the connection is OK or not .Before the email test, save the email setup information. 5.8.2.10 FTP The FTP interface is shown as in Figure 5-34.
Figure 5‐35 Refer to the following sheet for detailed information. Parameter Function PAT Check the corresponding box to enable PAT function. Status Dsiplay UPnP function status. It is corresponding to the UPnP mapping information on the router. Check the box before the service name to enable current PAT service. Otherwise, the service is null. Service name：Custmozied name. Prptocol：Protocol type. Internal port：The port maped to the port. External port：The port current device needs to map.
5.8.2.12 SNMP The SNMP interface is shown as in Figure 5-36. The SNMP allows the communication between the network management work station software and the proxy of the managed device. It is reserved for the 3rd party to develop. Figure 5‐36 Refer to the following sheet for detailed information. Parameter Function SNMP Port The listening port of the proxy program of the device. It is a UDP port not a TCP port. The value ranges from 1 to 65535. The default value is 161 Read Community It is a string.
5.8.2.13 Multicast The multicast interface is shown as in Figure 5-37. Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data packet, multiple-cast is the best option to reduce the broad width and the CPU load. The source host can just send out one data to transit. This function also depends on the relationship of the group member and group of the outer. Figure 5‐37 5.8.2.14 Auto Register The auto register interface is shown as below. See Figure 5-38.
5.8.2.16 HTTPS In this interface, you can set to make sure the PC can successfully login via the HTTPS. It is to guarantee communication data security. The reliable and stable technology can secure the user information security and device safety. See Figure 5-40. Note You need to implement server certificate again if you have changed device IP. You need to download root certificate if it is your first time to use HTTPS on current PC. Figure 5‐40 5.8.2.16.
Figure 5‐43 Click Open button, you can go to the following interface. See Figure 5-44. Figure 5‐44 Click Install certificate button, you can go to certificate wizard. See Figure 5-45. Figure 5‐45 Click Next button to continue. Now you can select a location for the certificate. See Figure 5-46.
Figure 5‐46 Click Next button, you can see the certificate import process is complete. See Figure 5-47. Figure 5‐47 Click Finish button, you can see system pops up a security warning dialogue box. See Figure 5-48. Figure 5‐48 Click Yes button, system pops up the following dialogue box, you can see the certificate download is complete. See Figure 5-49.
5.8.2.16.3 View and set HTTPS port From Setup->Network->Connection, you can see the following interface. See Figure 5-50. You can see HTTPS default value is 443. Figure 5‐50 5.8.2.16.4 Login Open the browser and then input https://xx.xx.xx.xx:port. xx.xx.xx.xx: is your device IP or domain mane. Port is your HTTPS port. If you are using default HTTPS value 443, you do not need to add port information here. You can input https://xx.xx.xx.xx to access.
Figure 5‐53 Figure 5‐54 Refer to the following sheet for detailed information. Parameter Function Enable You need to check the box to enable motion detection function. Select a channel from the dropdown list. Period Motion detection function becomes activated in the specified periods. See Figure 5-52. There are six periods in one day. Draw a circle to enable corresponding period. Click OK button, system goes back to motion detection interface, click save button to exit.
Parameter Function button to exit current setup. Do remember click save button to save current setup. If you click ESC button to exit the region setup interface system will not save your zone setup. Record channel System auto activates motion detection channel(s) to record once an alarm occurs. Note you need to set motion detect record period and go to Storage-> Schedule to set current channel as schedule record. Record Delay System can delay the record for specified time after alarm ended.
5.8.3.1.1 motion detect for detailed information. Figure 5‐55 5.8.3.1.3 Tampering The tampering interface is shown as in Figure 5-56. After analysis video, system can generate a tampering alarm when the detected moving signal reached the sensitivity you set here. For detailed setups, refer to chapter 5.8.3.1.1 motion detect for detailed information. Figure 5‐56 5.8.3.2 Alarm Before operation, make sure you have properly connected alarm devices such as buzzer.
Figure 5‐57 Figure 5‐58 Figure 5‐59 Refer to the following sheet for detailed information. Parameter Function Enable You need to check the box to enable this function. Select a channel from the dropdown list. Period This function becomes activated in the specified periods.
Parameter Function There are six periods in one day. Draw a circle to enable corresponding period. Select date. If you do not select, current setup applies to today only. You can select all week column to apply to the whole week. Click OK button, system goes back to local alarm interface, click save button to exit. Anti-dither System only memorizes one event during the anti-dither period. The value ranges from 5s to 600s. Sensor type There are two options: NO/NC.
Figure 5‐60 5.8.3.3 Abnormality It includes two types: No disk, disk error, disk no space, net disconnection, IP conflict and MAC conflict. See Figure 5-61 and Figure 5-62. Figure 5‐61 Figure 5‐62 Refer to the following sheet for detailed information. Parameter Function Event Type The abnormal events include: No disk, disk error, disk no space, net disconnection, IP conflict and MAC conflict. You can set one or more items here.
Parameter Function Show message System can pop up a message to alarm you in the local host screen if you enabled this function. Alarm upload System can upload the alarm signal to the centre (Including alarm centre. Send Email If you enabled this function, System can send out an email to alert you when an alarm occurs. Buzzer Check the box here to enable this function. The buzzer beeps when an alarm occurs. 5.8.4 Storage 5.8.4.
Figure 5‐65 Refer to the following sheet for detailed information. Parameter Function Channel Select a channel from the dropdown list. Pre-record Input pre-record time here. The value ranges from 0 to 30. Redundancy Check the box here to enable redundancy function. Note this function is null if there is only one HDD. Snapshot Check the box here to enable snapshot function. Holiday Check the box here to enable holiday function.
Figure 5‐66 5.8.4.3 Record The interface is shown as in Figure 5-67. Figure 5‐67 Refer to the following sheet for detailed information. Parameter Function Channel Here you can view channel number. The number displayed here is the max channel amount of your device. Status There are three statuses: schedule, manual and stop. Schedule System enables auto record function as you set in record schedule setup (general, motion detect and alarm). Manual It has the highest priority.
5.8.5 Setting 5.8.5.1 General The general interface includes general, date/time and holiday setup. 5.8.5.1.1 General The general interface is shown as in Figure 5-68. Figure 5‐68 Refer to the following sheet for detailed information. Parameter Function Device ID It is to set device name. Device No. It is device channel number. Language You can select the language from the dropdown list. Note the device needs to reboot to get the modification activated.
Refer to the following sheet for detailed information. Parameter Function Date format Here you can select date format from the dropdown list. Time Format There are two options: 24-H and 12-H. Time zone The time zone of the device. System time It is to set system time. It becomes valid after you set. Sync PC You can click this button to save the system time as your PC current time. DST Here you can set day night save time begin time and end time.
5.8.5.2 Display Display interface includes GUI, TV adjust, Tour and zero-channel encoding. 5.8.5.2.1 Display Here you can set background color and transparency level. See Figure 5-71. Figure 5‐71 Refer to the following sheet for detailed information. Parameter Function Resolution There are four 1920×1080,1280×1024(default),1280×720,1024×768. system needs to reboot to activate current setup. Transparency Here is for you to adjust transparency. The value ranges from 128 to 255.
Parameter Function Enable tour Check the box here to enable tour function. Interval Here is for you to adjust transparency. The value ranges from 5 to 120s. The default setup is 5s. Split Here you can set window mode and channel group. System can support 1/4/8-window according to device channel amount. Motion tour/Alarm tour Here you can set motion detect tour/alarm tour window mode. System supports 1/8-window now. 5.8.5.2.3 Zero Channel The zero-channel interface is shown as in Figure 5-73.
Figure 5‐74 Refer to the following sheet for detailed information. Parameter Function Channel Select speed dome connected channel. PTZ type There are two options: local/remote. Control mode You can select control mode from the dropdown list. There are two options: Serial/HDCVI. For HDCVI series product, select HDCVI. The control signal is sent to the PTZ via the coaxial cable. For the serial mode, the control signal is sent to the PTZ via the RS485 port.
With the protocol For ATM/POS with the protocol, you just need to set the source IP, destination IP (sometimes you need to input corresponding port number). Figure 5‐75 Without the protocol For the ATM/POS without the protocol, the interface is shown as in Figure 5-76. Source IP refers to host IP address that sends out information (usually it is the device host.) Destination IP refers to other systems that receive information. Usually you do not need to set source port and target port.
The user amount default setup is 64 and the group amount default setup is 20. The factory default setup includes two levels: user and admin. You can set the corresponding group and then set the rights for the respective user in the specified groups. User management adopts group/user modes. The user name and the group name shall be unique. One user shall be included in only one group. 5.8.5.5.1 User name In this interface you can add/remove user and modify user name. See Figure 5-77.
Modify user It is to modify the user property, belonging group, password and rights. See Figure 5-79. Modify password It is to modify the user password. You need to input the old password and then input the new password twice to confirm the new setup. Click the OK button to save. Note, the password ranges from 1-digit to 6-digit. It shall include the number only. For the user of the account rights, he can modify the password of other users. Figure 5‐79 5.8.5.5.
Add group: It is to add group and set its corresponding rights. See Figure 5-81. Input the group name and then check the box to select the corresponding rights. It includes: shutdown/reboot device, live view, record control, PTZ control and etc. Figure 5‐81 Modify group Click the modify group button, you can see an interface is shown as in Figure 5-82. Here you can modify group information such as remarks and rights. Figure 5‐82 5.8.5.
If you want to use the auto delete old files function, you need to set the file period. Click Manual reboot button, you can restart device manually. Figure 5‐83 5.8.5.7 Import/Export The interface is shown as in Figure 5-84. Figure 5‐84 Refer to the following sheet for detailed information. Parameter Function Import It is to import the local setup files to the system. Export It is to export the corresponding WEB setup to your local PC. 5.8.5.
Figure 5‐86 5.8.6 Info 5.8.6.1 Version The version interface is shown as in Figure 5-87. Here you can view record channel, alarm input/output information, software version, release date and etc. Note the following information is for reference only. Figure 5‐87 5.8.6.2 Log Here you can view system log. See Figure 5-88. Figure 5‐88 Refer to the following sheet for log parameter information.
Parameter Function Clear You can click this button to delete all displayed log files. system does not support clear by type. Backup You can click this button to backup log files to current PC. Note 5.8.6.3 Online User The online user interface is shown as in Figure 5-89. Figure 5‐89 5.9 Playback Click Playback button, you can see an interface is shown as in Figure 5-90. Figure 5‐90 5.9.1 Search Record Set record type, record date, window display mode and channel name.
Select window split mode. Click 5-91. to display in full screen. Click ESC button to exit. See Figure Figure 5-91 Select Channel 1～4 means main stream and A1～A4 means sub stream. Select Record Type Check the corresponding box to select record type. See Figure 5-92. Figure 5‐92 5.9.2 File List Click File list button, you can see the corresponding files in the list. See Figure 5-93. Figure 5‐93 5.9.3 Playback Select a file you want to play and then click Play button, system can begin playback.
Figure 5‐94 5.9.4 Download Select the file(s) you want to download and then click download button, you can see an interface shown as in Figure 5-95. The Download button becomes Stop button and there is a process bar for your reference. Go to you default file saved path to view the files. Figure 5‐95 5.9.5 Load more It is for you to search record or picture. You can select record channel, record type and record time to download. Or you can use watermark function to verify file.
5.9.5.1 Download By File Select channel, record type, bit stream type and then input start time and end time. Click Search button, the download by file interface is shown as in Figure 5-96. Figure 5‐96 Check the file(s) you want to download and there are two options for you to save the file(s). Download to local Click Download to local, system pops up the following interface for you to set record format and saved path.See Figure 5-97.
Select Backup device and backup type first and then click Start backup button. After the download operation, you can see corresponding dialogue box. 5.9.5.2 Download by Time Select channel, bit stream type, start time and end time. Click Download to Local button, you can see download by time interface is shown as in Figure 5-99. Figure 5‐99 Set record format and saved path, you can click OK to download and view the download process. After the download operation, you can see corresponding dialog box. 5.9.
5.10 Alarm Click alarm function, you can see an interface is shown as Figure 5-101. Here you can set device alarm type and alarm sound setup (Make sure you have enabled audio function of corresponding alarm events.). Figure 5‐101 Refer to the following sheet for detailed information. Type Parameter Function Alarm Type Video loss System alarms when video loss occurs. Motion detection System alarms when motion detection alarm occurs. Tampering System alarms when camera is viciously masking.
5.11 Log out Click log out button, system goes back to log in interface. See Figure 5-102. You need to input user name and password to login again. Figure 5‐102 5.12 Un-install Web Control You can use web un-install tool “uninstall web.bat” to un-install web control. Note, before you un-installation, close all web pages, otherwise the un-installation might result in error.
6 Professional Surveillance System Besides Web, you can use our Smart PSS to login the device. For detailed information, refer to Smart PSS user’s manual.
7 FAQ 1. DVR can not boot up properly. There are following possibilities: Input power is not correct. Power connection is not correct. Power switch button is damaged. Program upgrade is wrong. HDD malfunction or something wrong with HDD ribbon. Seagate DB35.1，DB35.2，SV35 or Maxtor 17-g has compatibility problem. Upgrade to the latest version to solve this problem. Front panel error. Main board is damaged. 2. DVR often automatically shuts down or stops running.
Video transmission is too long or degrading is too huge. DVR color or brightness setup is not correct. 6. Can not search local records. There are following possibilities: HDD ribbon is damaged. HDD is broken. Upgraded program is not compatible. The recorded file has been overwritten. Record function has been disabled. 7. Video is distorted when searching local records. There are following possibilities: Video quality setup is too low.
Front panel PTZ error PTZ decoder setup, connection or installation is not correct. Cable connection is not correct. PTZ setup is not correct. PTZ decoder and DVR protocol is not compatible. PTZ decoder and DVR address is not compatible. When there are several decoders, add 120 Ohm between the PTZ decoder A/B cables furthest end to delete the reverberation or impedance matching. Otherwise the PTZ control is not stable. The distance is too far. 12.
15. Network connection is not stable. There are following possibilities: Network is not stable. IP address conflict. MAC address conflict. PC or DVR network card is not good. 16. Burn error /USB back error. There are following possibilities: Burner and DVR are in the same data cable. System uses too much CPU resources. Stop record first and then begin backup. Data amount exceeds backup device capacity. It may result in burner error. Backup device is not compatible.
HDD capacity is not enough. HDD is damaged. 22. Can not playback the downloaded file. There are following possibilities: There is no media player. No DXB8.1 or higher graphic acceleration software. There is no DivX503Bundle.exe control when you play the file transformed to AVI via media player. No DivX503Bundle.exe or ffdshow-2004 1012 .exe in Windows XP OS. 23. Forgot local menu operation password or network password Contact your local service engineer or our sales person for help.
This product includes software developed by third parties, including software which is released under the GNU General Public License Version 2 (GPL v2). This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
5. You are not required to accept this License, since you have not signed it. Nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6.
Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time.
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS HOW TO APPLY THESE TERMS TO YOUR NEW PROGRAMS If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your program.
