User Manual

2. Once charging commences, the Red LED will on.
3. When the Battery is fully charged, the Red LED will off and Green LED will on.
Battery Charge Level: The Battery has a built-in Battery Charge Indicator
Pressing on the button to the right will indicate the charge level. The right LED indicates a high
charge level and the left a low charge level that will mean the battery pack will require charging
soon.
MPORTANT: When a low charge level is indicated, the tool may stop operating while in use,
which is dangerous when operating a circular saw. Always ensure the battery pack has a good
charge level.
Note: about battery charging:
- The battery should be charged at ambient temperatures between 10 and 40°C.
(ideally around 20°C)
- After charging, allow 15 minutes for the battery to cool before use.
- Ensure that the charger is disconnected from the mains supply after use, and is stored
correctly.
- DO NOT leave batteries on charge for extended periods and NEVER store batteries on charge
- The Battery Charger monitors battery temperature and voltage while charging. Remove the
Battery once charging is complete to maximise charge cycles of the battery and not waste
power.
- Batteries can become faulty over time, individual cells in the battery can fail and the battery
could short. The charger will not charge faulty batteries. Use another battery, if possible, to
check correct functionality of the charger and purchase a replacement battery if a faulty battery
is indicated.
- DO NOT store lithium-ion battery packs in a discharged state over a long period as this can
damage the lithium-ion cells. For long-term storage, store batteries in a high charge state
disconnected from the power tool.
- The capacity of batteries will reduce over time. After 100 charge cycles, the battery’ s
operation time and the maximum torque performance of the driver will slightly reduce. This
decline will continue until the battery has minimal capacity after 250 charge cycles. This is
normal and not a fault with the battery pack.
Fitting drill bits and accessories
WARNING: ALWAYS remove the Battery from the drill before attaching, adjusting or removing
accessories.
WARNING: DO NOT attempt to tighten drill bits (or any other accessory) by gripping the front
part of the chuck and switching the tool on. This can lead to personal injury and can cause
damage to the chuck.
WARNING: NEVER fit any accessory or bit with a maximum speed lower than the no load speed
of he power tool.
1. Open the Chuck by rotating the Chuck (1) anti-clockwise
2. Place the drill bit or accessory centrally into the chuck
3. Tighten the Chuck Jaws by rotating the Chuck Collar clockwise
4. When the drill bit or accessory is securely fastened, carefully run the
Machine to test that it is running centrally, smoothly and evenly. If the bit is 'wobbling' or not
running centrally, release the chuck, check the accessory for damage,correct its position,
retighten and test again.
Operation
Direction control
WARNING: NEVER change the direction of rotation while the tool is running. This may cause
permanent damage to the tool.
- The direction of rotation can be set using the Forward/Reverse Switch (6)
- For anti-clockwise rotation, push the switch to the right
- For clockwise rotation, push the switch to the left
Note: When the Forward/Reverse Switch is in the central position,
the drill is locked and cannot be switched on. Use this setting as
a safety feature to prevent the drill from being switched on accidentally.
Torque control
Note: This cordless drill is equipped with a torque control clutch allowing the machine to be set to
the correct torque for the individual application.
- The clutch settings are indicated by the symbols on the
Torque Selector (2)
- Rotate the Torque Selector to select the desired setting:
the higher the number displayed on the torque ring,
the higher the torque produced by the too.
Gear selection
- Select gear 1 on the Gear Switch (4) for the higher torque.
A lower speed gear is generally more suitable for driving screws
and fasteners.
- Select gear 2 on the Gear Switch for the lower torque.
A higher speed gear is for drilling and must not be used
for driving screws and fasteners.
Note: ALWAYS read the documentation provided with drill bits and accessories for the
recommended or maximum speed setting and use the most appropriate gear. See ‘Specification’
for the maximum no load speed of each gear.
Switching on/off
WARNING: ALWAYS wear adequate personal protection equipment when setting up and
operating this machine.
1. To start the drill, squeeze the Trigger Switch (7).
2. The built-in Work Light (9) will illuminate when the Trigger Switch is squeezed.
Note: If the Trigger Switch cannot be pressed down, check that the Forward/Reverse Switch (6)
is not set to its middle position, which locks the device (see ‘Direction control’ ).
3. The speed of the drill is controlled by the movement of the trigger: the further the Trigger
Switch is pressed down, the faster the drill will run.
4. Release the Trigger Switch to stop the machine.
6
10
- -