Installation Instructions

Product Data
Premixed Vinyl Tile Grout
1. PRODUCT NAME
TEC
®
Premixed Vinyl Tile Grout
(TA-639)
2. MANUFACTURER
H.B. Fuller Construction Products Inc.
1105 South Frontenac Street
Aurora, IL 60504-6451 U.S.A.
800.552.6225 Office
800.952.2368 Fax
tecspecialty.com
3. DESCRIPTION
TEC
®
Premixed Vinyl Tile Grout is a ready-to-use, premixed, sanded acrylic grout
that is highly stain resistant for use with vinyl tile. TEC
®
Premixed Vinyl Tile Grout
is formulated to be used in grout joints from
1
⁄8 inch to
1
⁄4 inch.
Key Features and Benefits
• Highly stain resistant, no need to seal
• Grout is mold and mildew resistant
• Durable, wear resistant
• Easy to use
Packaging
1
⁄
2
gallon plastic pail (1.89 L)
Color
Antique White Light Pewter
Light Smoke Pearl
Coverage
Figures shown in the chart are presented only as guidelines.
Approximate Coverage per
1
⁄
2
gallon (1.89 L)
Vinyl Tile Size
Joint Width
1
⁄8 "
(3 mm)
3
⁄16 "
(4.5 mm)
1
⁄4 "
(6 mm)
12" x 12"
(300 mm x 300 mm)
300 sq. ft.
(27.8 m
2
)
200 sq. ft.
(18.6 m
2
)
150 sq. ft.
(13.9 m
2
)
18" x 18"
(450 mm x 450 mm)
450 sq. ft.
(41.8 m
2
)
300 sq. ft.
(27.8 m
2
)
225 sq. ft.
(20.9 m
2
)
Storage
Store indoors in a cool, dry location. Keep away from excessive heat. Keep from
freezing. If frozen, slowly bring material back to room temperature and mix per
instructions.
Shelf Life
Maximum of 1 year from date of manufacture in unopened package. Product good
for 6 months after opening as long as bucket is re-sealed carefully and stored in
a cool, dry, interior location and used within shelf life. Covering with plastic wrap
directly on top of product prior to sealing container will help preserve freshness.
Limitations
• Not for exterior use.
• Do not apply in temperatures below 50°F (10°C) or above 90°F (32°C).
• Not for use in grout joints wider than
1
⁄
4
inch (6 mm).
• Do not add water.
• Keep from freezing.
• Keep at room temperature for 24 hours prior to use.
Cautions
Read complete cautionary information printed on product container prior to use.
For medical emergency information, call 1-888-853-1758.
This Product Data Sheet has been prepared in good faith on the basis of information
available at the time of publication. It is intended to provide users with information
about and guidelines for the proper use and application of the covered TEC
®
brand
product(s) under normal environmental and working conditions. Because each
project is different, H.B. Fuller Construction Products Inc. cannot be responsible
for the consequences of variations in such conditions, or for unforeseen conditions.
4. TECHNICAL DATA
Physical Properties
TEC
®
Premixed Vinyl Tile Grout (TA-639)
Description
Physical State Paste
Color Available in 4 standard colors
Light Foot Traffic [at 72°F (22°C)] 24 hours
Final Cure (full stain & water resistance) 7 days
VOC/Liter of Material 15 grams
Foot Traffic Rating (ASTM C627) Residential
Storage
Store in cool, dry location. Do not
store open containers. KEEP FROM
FREEZING.
Shelf Life
Maximum 1 year from date of manufacture
in properly stored, unopened package.
5. INSTALLATION INSTRUCTIONS
Surface Preparation
Grout joints must be clean, dry, free of dirt and dust. Wipe down vinyl tile surface with
a slightly dampened sponge before grouting.
Application
1. Grout no more than 10 sq. ft. (0.93 m
2
) at a time.
2. Press grout diagonally into joints holding float at a 45-degree angle. Make sure
that joints are completely filled
3. Remove all excess grout off vinyl tile by holding float at a 90-degree angle and
drawing diagonally across tile.
4. To clean, first soak sponge in cool clean water. Wring out completely.
5. Use the damp sponge in a light, circular motion to smooth joints and clean film
from the vinyl tile. Avoid using excessive amounts of water on the grout joints.
6. Turn sponge over to a clean side and draw diagonally across vinyl tiles to
remove any remaining film.
7. Wait 10 minutes, then buff vinyl tile with a soft clean cloth to remove remaining
grout film.
8. There is no need to seal TEC
®
Premixed Vinyl Tile Grout.
NOTE: If excess water is used in the sponge during clean up, minor cracks or
pinholes can develop. If the grout is over-worked, it may appear to shrink down
into joint. Should this occur, simply apply a second coat to the affected areas.
You must allow your initial application to cure for 24 hours prior to your second
application.
Existing Grout Repairs
Completely remove existing grout from the joints. Do not damage vinyl tile.
Vacuum dust from vinyl tile surface and grout joints. Follow application
instructions.
VOC 15 g/L