Installation Instructions

Product Data
Vinyl Composition Tile Adhesive
1. PRODUCT NAME
TEC
®
Vinyl Composition Tile Adhesive
(713)
2. MANUFACTURER
H.B. Fuller Construction Products Inc.
1105 South Frontenac Street
Aurora, IL 60504-6451 U.S.A.
800.552.6225 Office
800.952.2368 Fax
tecspecialty.com
3. DESCRIPTION
TEC
®
Vinyl Composition Tile Adhesive is a permanent pressure sensitive latex
adhesive for the interior installation of Vinyl Composition Tile (VCT). When used
according to directions, Vinyl Composition Tile Adhesive will bond new tile to old
floor coverings. The outstanding features of this adhesive are ease of application,
immediate grab, transparent-clear dry film and freeze/thaw stability. Not for use
with solid vinyl tile.
Key Features and Benefits
• Premium quality
• Dries clear
• Zero VOC/low odor
Packaging
1 quart plastic pails (.946 L) Product #7047495117
1 gallon plastic pails (3.79 L) Product #7047495017
3.5 gallon plastic pails (13.24 L) Product #7047491217
Coverage
Coverage will vary with the absorption of substrate and trowel size. Figures below
are presented only as guidelines.
Flooring Type
Recommended
Trowel Size
Approximate Coverage in sq. ft. (m
2
)
Quart Gallon 3.5 Gallon
Porous substrates
1
⁄
16
" x
1
⁄
16
" x
1
⁄
16
"
(1.6 x 1.6 x 1.6 mm)
square-notch trowel
40.5-45
(3.8-4.2)
160-180
(14.9-16.7)
560-630
(52.0-58.5)
Porous and
non-porous
substrates
1
⁄
32
" x
1
⁄
16
" x
5
⁄
64
"
(0.8 x 1.6 x 2.0 mm)
U-notch trowel
75-87.5
(7.0-8.1)
300-350
(27.9-32.5)
1050-1225
(97.5-113.8)
Suitable Substrates
When properly prepared, suitable, clean, dry, sound substrates include:
• Concrete - on, above or below grade, in the absence of excessive moisture and
alkali
• Plywood - APA standard underlayment grade or better
• Multiply underlayment
• Fiber-cement underlayment
• Latex Portland cement based underlayment
• Well bonded, smooth, wax-free, existing single layer non-cushioned resilient
flooring
Storage
Store inside at temperatures of 60°F to 100°F. Best to keep from freezing. If
frozen, allow to thaw before use. Keep container tightly closed when not in use.
Always store in an upright position.
Shelf Life
Maximum of 18 months from date of manufacture in unopened container.
Limitations
• Not for installing solid vinyl tile or self-stick vinyl tile.
• Do not use where hydrostatic pressure, excessive moisture or alkali is present.
• New concrete should be allowed to cure a minimum of 60-90 days prior to
installation.
• Not recommended for installation over cushion-backed or unprepared
embossed sheet goods, lauan and unprimed gypsum.
• Freeze/thaw stable to 10°F for a maximum of 5 cycles. If frozen, slowly bring to
room temperature and stir before using.
• DO NOT USE IN MARINE APPLICATIONS.
Cautions
Read complete cautionary information printed on product container prior to use.
For medical emergency information, call 1-888-853-1758.
This Product Data Sheet has been prepared in good faith on the basis of information
available at the time of publication. It is intended to provide users with information
about and guidelines for the proper use and application of the covered TEC
®
brand
product(s) under normal environmental and working conditions. Because each
project is different, H.B. Fuller Construction Products Inc. cannot be responsible
for the consequences of variations in such conditions, or for unforeseen conditions.
4. TECHNICAL DATA
Physical Properties
TEC
®
VInyl Composition Tile Adhesive (713)
Description
Base Latex
Physical State Thin paste
Color
Off-white — wet
Clear — dry
Working Time 1 to 24 hours
VOC/Liter of Material 0 g/L (calculated)
5. INSTALLATION INSTRUCTIONS
Substrate Preparation
For best results, flooring material, room and adhesive should be kept at a
minimum of 65°F for 48 hours before, during and 24 hours after installation.
Remove all wax, grease, oil, paint, dust, curing compounds and other surface
contaminants. Plywood should be installed according to American Plywood
Association guidelines. Plywood subfloor surfaces should be well nailed at all
edges and through center. Raised edges should be sanded smooth. Fill all cracks
and depressions with a quality patching compound. Sand smooth and vacuum to
remove dust. On hardwood and wood parquet floors, the installation of plywood or
fiber-cement underlayment is required.
All concrete substrates must be tested for moisture and pH prior to flooring
installation. Install flooring with TEC
®
Vinyl Composition Tile Adhesive over
concrete with a moisture vapor emission rate up to 5 lbs. per 1,000 sq. ft.
(2.26 kg/ 93 m²) per 24 hours when tested in accordance with ASTM F1869. Test
for pH in accordance with ASTM F710. Range of 7-9 is required.
Application
Refer to flooring manufacturers installation guidelines for proper application
instructions, including trowel size and approximate coverage. TEC
®
Vinyl
Composition Tile Adhesive has an approximate working time of 1-24 hours,
depending on trowel size, floor porosity, temperature and humidity. Apply adhesive
and allow to dry to a clear, transparent film - normally 30-45 minutes before
applying tiles. However, tiles may be installed up to 24 hours after spreading
adhesive (dependent on trowel notch selected). Drying time will vary depending
upon the temperature and humidity. Check readiness by lightly pressing a finger
on adhesive. If there is no adhesive transfer to finger when lightly touched, tiles
may be set by pressing down firmly. Keep the adhesive film free of dust and dirt.
VOC 0 g/L