Installation Instructions

Product Data
1. PRODUCT NAME
TEC
®
Premium Sheet Vinyl Adhesive
(722)
2. MANUFACTURER
H.B. Fuller Construction Products Inc.
1105 South Frontenac Street
Aurora, IL 60504-6451 U.S.A.
800.552.6225 Office
800.952.2368 Fax
tecspecialty.com
3. DESCRIPTION
TEC
®
Premium Sheet Vinyl Adhesive is an excellent product providing
performance and value for many types of installations. This adhesive’s
characteristics make it equally suited for installing both sheet goods and carpet.
Key Features and Benefits
• Solvent free
• Extended open time
• Zero VOC
Packaging
1 quart plastic pails (.946 L) Product #7047105117
1 gallon plastic pails (3.79 L) Product #7047105017
3.5 gallon plastic pails (13.24 L) Product #7047101217
Coverage
Coverage will vary with the absorption of substrate and trowel size. Figures below
are presented only as guidelines.
Flooring Type
Recommended
Trowel Size
Approximate Coverage in sq. ft. (m
2
)
Quart Gallon 3.5 Gallon
Resilient
sheetgoods;
resilient floor tile
1
⁄
16
" x
1
⁄
16
" x
1
⁄
16
"
(1.6 x 1.6 x 1.6 mm)
square-notch trowel
40.5-45
(3.8-4.2)
160-180
(14.9-16.7)
560-630
(52.0-58.5)
Resilient
sheetgoods
installed over
existing resilient
1
⁄
32
" x
1
⁄
16
" x
5
⁄
64
"
(0.8 x 1.6 x 2.0 mm)
U-notch trowel
75-87.5
(7.0-8.1)
300-350
(27.9-32.5)
1050-1225
(97.5-113.8)
Suitable Substrates
When properly prepared, suitable, clean, dry, sound substrates include:
• Concrete
• Marble
• Terrazzo
• Metal
• Plywood
• Hardboard underlayment
• Association grade particleboard underlayment.
Approved Flooring
• Sheet goods include but are not limited to: Mineral and Felt Back
Storage
Store inside at temperatures of 60°F to 100°F. Best to keep from freezing. If
frozen, allow to thaw before use. Keep container tightly closed when not in use.
Always store in an upright position.
Shelf Life
Maximum of 18 months from date of manufacture in unopened container.
Limitations
• Interior use only.
• Do not use to install solid vinyl, vinyl back, urethane back nor fiberglass back
products.
• Not recommended for installation over cushion backed or unprepared embossed
sheet goods, lauan and unprimed gypsum.
• Do not use where hydrostatic pressure exists.
• New concrete should be allowed to cure a minimum of 28 days.
• Not for use in the presence of moisture or high alkalinity (pH greater than 9).
• Do not allow to freeze.
• Keep container sealed when not in use.
• Do not use when the substrate temperature is below 50°F or above 90°F.
• Do not use in marine applications.
Cautions
Read complete cautionary information printed on product container prior to use.
For medical emergency information, call 1-888-853-1758.
This Product Data Sheet has been prepared in good faith on the basis of information
available at the time of publication. It is intended to provide users with information
about and guidelines for the proper use and application of the covered TEC
®
brand
product(s) under normal environmental and working conditions. Because each
project is different, H.B. Fuller Construction Products Inc. cannot be responsible
for the consequences of variations in such conditions, or for unforeseen conditions.
4. TECHNICAL DATA
Physical Properties
TEC
®
Premium Sheet Vinyl Adhesive (722)
Description
Base Latex
Physical State Medium paste
Color Beige
Open Time
30-45 minutes (depending on temperature, humidity,
and condition of floor)
VOC/Liter of Material 0 g/L (calculated)
5. INSTALLATION INSTRUCTIONS
Substrate Preparation
Floor must be clean, smooth, dry, and free of any foreign matter that would
interfere with a good bond. Fill all cracks and depressions with a suitable floor
patch. For best results, the area to be installed, adhesive and flooring should be
conditioned at 65°F and at a maximum relative humidity of 65% for at least 24
hours before and after installation.
Moisture Test - All concrete floors should be tested for moisture emission
rate by utilizing an anhydrous calcium chloride moisture test kit, (available
from installation supplies and accessories dealers.) Follow kit manufacturer’s
instructions precisely to determine moisture emissions. Follow floor covering
manufacturers recommendations for moisture vapor emissions.
Application
1. Lay out flooring material according to manufacturer’s specifications.
2. Apply adhesive evenly to the substrate according to industry standards or as
recommended by the flooring manufacturer.
3. Set the material into the adhesive within 20 minutes after troweling. Material
can be adjusted within this time. Lift a corner of material periodically to see
that the adhesive is transferring 100% to the material backing. If sufficient
transfer is not attained, apply additional adhesive.
4. Press and smooth material firmly into the adhesive with a roller, according to
manufacturer’s recommendations.
VOC 0 g/L
Premium Sheet Vinyl Adhesive