Installation Instructions

Product Data
Releasable Pressure-Sensitive Adhesive
1. PRODUCT NAME
TEC
®
Releasable Pressure-Sensitive Adhesive
(749)
2. MANUFACTURER
H.B. Fuller Construction Products Inc.
1105 South Frontenac Street
Aurora, IL 60504-6451 U.S.A.
800.552.6225 Office
800.832.9023 Technical Support
800.952.2368 Fax
tecspecialty.com
3. DESCRIPTION
TEC Releasable Pressure-Sensitive Adhesive is a high quality, high strength,
adhesive with excellent resistance to plasticizer migration. Can be used for
installation of carpet tile, fiberglass-backed flooring and for adhering cushion to
substrate in the Double-Bond Method of Installations as well as for peel-n-stick
vinyl tiles.
Key Features and Benefits
• For commercial and residential applications
• Modular carpet tile / vinyl backed carpet
• Double-bond method of installation (cushion to substrate)
• Low odor
Zero VOC
Packaging
1 quart plastic pails (946 mL) Product #15036376
1 gallon plastic pails (3.78 L) Product #15036375
1 gallon plastic pails (3.78 L) Canadian Product #15035541
3.5 gallon plastic pails (13.24 L) Product #15036377
4 gallon plastic pails (15.13 L) Product #15035538
Coverage
Determine recommended trowel size based on tile type. Coverage will vary with
the absorption of substrate and trowel size. Figures below are presented only as
guidelines.
Flooring Type
Recommended
Trowel Size
Approximate
Coverage
Porous substrate
1
16
" x
1
16
" x
1
16
"
(1.6 x 1.6 x 1.6 mm)
square-notch trowel
162-180 sq. ft./gal.
18-20 yd
2
/gal.
(4-4.4 m
2
/L)
Non-porous substrate
1
32
" x
1
32
" x
1
16
"
(0.8 x 0.8 x 1.6 mm))
U-notch trowel
220-260 sq. ft./gal
24-28 yd
2
/gal.
(5.3-6.2 m
2
/L)
Brush or rolled
225-260 sq. ft./gal.
24-28 yd
2
/gal.
(5.5-6.2 m
2
/L)
Suitable Interior Substrates
When properly prepared, suitable substrates include:
Concrete
• Marble and terrazzo
• Metal
• Plywood - APA standard underlayment grade or better
• Multiply Underlayment
• Fiber-cement underlayment
• Portland cement based underlayment
Well bonded, smooth, wax-free, existing single layer non-cushioned resilient
flooring.
• Radiant heated subfloors [surface temperature does not exceed 85°F (29°C)]
Substrate Preparation
Subfloor should be structurally sound, clean, dry and level. Remove all grease,
sealers, curing compounds, loose paint, dirt, etc. Nail down any loose edges or
areas of subfloor and sand smooth all raised edges. Fill cracks or depressions
in floor with a suitable TEC patching compound. Sand smooth and vacuum to
remove dust. Over hardwood floors or wood parquet, the installation of plywood
or fiber-cement underlayment is required. Plywood should be installed according
to American Plywood Association guidelines. Plywood subfloor surfaces should be
well nailed at all edges and through center.
All concrete substrates must be tested for moisture and pH prior to flooring
installation. Install flooring with TEC Releasable Pressure-Sensitive Adhesive over
concrete with a moisture vapor emission rate up to 10 lbs. per 1,000 sq. ft. (4.54
kg/93 m²) per 24 hours when tested in accordance with ASTM F1869 or up to
90% RH when tested in accordance with ASTM F2170. For concrete with greater
moisture levels, treat the concrete with TEC LiquiDam
Penetrating Moisture
Vapor Barrier. See Product's Data Sheet for details. Test for pH in accordance with
ASTM F710. Range of 7-9 is required.
Storage
Store in cool, dry location. Do not store open containers.
Shelf Life
Maximum of 18 months from date of manufacture in unopened container.
Limitations
• Do not use where hydrostatic pressure, excessive moisture or alkali is present.
New concrete should be allowed to cure a minimum of 60-90 days prior to
installation.
• Do not use when temperature is below 60°F (15°C).
Not recommended for installation over cushion-backed or unprepared
embossed sheetgoods.
Freeze/thaw stable to 10°F (-12°C) for a minimum of 5 cycles. If frozen, slowly
bring to room temperature and stir before using.
Cautions
Read complete cautionary information printed on product container prior to use.
For medical emergency information, call 1-888-853-1758.
This Product Data Sheet has been prepared in good faith on the basis of information
available at the time of publication. It is intended to provide users with information
about and guidelines for the proper use and application of the covered TEC brand
product(s) under normal environmental and working conditions. Because each
project is different, H.B. Fuller Construction Products Inc. cannot be responsible
for the consequences of variations in such conditions, or for unforeseen conditions.
4. TECHNICAL DATA
Physical Properties
TEC Releasable Pressure Sensitive Adhesive (749)
Description
Base Acrylic latex
Physical State Thin paste
Color
Off-white — wet
Clear — dry
Working Time
Permanently pressure sensitive once cured provided it
is kept clean and dust free.
VOC/Liter of Material 0 g/L, less water
Freeze/Thaw Stability
Freeze/thaw stable to 10°F (-12°C) for a minimum of
5 cycles. If frozen, slowly bring material back to room
temperature and stir before using.
Storage
Store in cool, dry location. Do not store open
containers.
Shelf Life
Maximum 18 months from date of manufacture in
properly stored, unopened package.

Summary of content (2 pages)