ASC8023 Team Associated RC10F6 Manual

ManualsBrandsTeam Associated ManualsCars & TrucksRC10F6 Factory Team 1/10 Competition F1 Chassis Kit

Summary of content (26 pages)

PAGE 1
PAGE 2
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10F6 Kit. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.
PAGE 3
:: Hardware - 1:1 Scale View Button Head (bhcs) Flat Head (fhcs) Socket Head (shcs) 2x4mm (31510) FT 2x4mm Aluminum (8545) 2x6mm (4674) FT 2x6mm Aluminum (8547) 3x6mm (31531) FT 3x6mm Aluminum (8550) FT 3x6mm Titanium (91580) 2.5x6mm (4675) FT 2.5x6mm Aluminum (8549) 3x8mm (31532) FT 3x8mm Aluminum (8552) FT 3x8mm Titanium (91581) 3x10mm (25211) FT 3x10mm Aluminum (8554) FT 3x10mm Titanium (91582) Ballstuds Black 3.25mm Short (31390) FT TiN 3.25mm Short (31374) Silver 3.25mm Long (31391) FT TiN 3.
PAGE 4
:: Table of Contents 1................... Cover 2................... Introduction 3................... 1:1 Hardware “Fold Out” 4................... Table of Contents 5 - 6..............Shock, Damper Tubes & Turnbuckles Build (Bag 1.1, 1.2) 6 - 9..............Front Suspension Build (Bag 2.1, 2.2) 9 - 11............Rear Suspension Build (Bag 3.1, 3.2) 11 - 12........Axle Build (Bag 4.1, 4.2) 13 - 15........Wings, Electronics, Wheel and Body Build (Bag 5.1, 5.2) 16 - 17......
PAGE 5
2/17 :: Center Shock Build - Bag 1.1, 1.2 - Step 1 31510 2x4mm BHCS 31687 FT Shock Body (Fox Kashima Coat) #1596 thread lock 21139 Steel Washer (2.6x6x0.5mm) 31689 Shock Piston, 3x1.1 31688 Shock Shaft 31693 Shock Hat Bushing 31327 Shock Bottom Cap 5407 Red O-Ring 31327 Shock Bottom Cap O-Ring 4637 FT Pivot Ball 31700 Shock Eyelet :: Center Shock Build - Bag 1.1, 1.
PAGE 6
:: Turnbuckles Build - Bag 1.1, 1.2 - Step 4 Steering Turnbuckle 31305 x2 Turnbuckle Eyelet Servo Turnbuckle 41.8mm 24.9mm ! Build two Steering turnbuckles 9175 Turnbuckle 3x58mm 31305 x2 Turnbuckle Eyelet 6266 Turnbuckle 3x38mm ! 4404 Turnbuckle 3x45mm ! For Long Steering Bellcrank, use #4404 45mm Turnbuckle (See page 9) 30.0mm :: Front Suspension Build - Bag 2.1, 2.
PAGE 7
:: Front Suspension Build - Bag 2.1, 2.2 - Step 3 KO, Jr, Sanwa, Airtronics : 23T Hi Tec: 24T Reedy, XP, Futaba: 25T 31283 Ballstud 5mm, Long 8674 RC10F6 Servo Mount, Floating 31550 FT Aluminum M3 Locknut, Blue 8689 Servo Saver 8674 RC10F6 Servo Mount, Fixed 31532 x4 3x8mm BHCS ! Servo not included! 31531 3x6mm BHCS :: Front Suspension Build - Bag 2.1, 2.
PAGE 8
:: Front Suspension Build - Bag 2.1, 2.2 - Step 6 4754 x3 Suspension Arm Pivot Ball Bushing 4755 x3 Suspension Arm Pivot Ball, Upper 25211 x2 3x10mm BHCS Racer’s Tip: Use CA Glue for permanent mounting! 31381 x2 Aluminum Ballstud Washer, 5.5x0.5mm 4754 x3 Suspension Arm Pivot Ball Bushing O-Ring ! 8638 Suspension Arm, Upper Build left and right sides :: Front Suspension Build - Bag 2.1, 2.
PAGE 9
:: Front Suspension Build - Bag 2.1, 2.2 - Step 9 #8670 Steering Bellcranks Steering Bellcrank, Short Steering Bellcrank, Long Kit Setup Use for tuning adjustment of steering rate. Requires #4404 - 45mm Steering Turnbuckle (included) Steering Turnbuckles Servo Turnbuckle :: Front Suspension Build - Bag 2.1, 2.2 - Step 10 Kit Setup: ! ! Upper arms hidden for view clarity Note position of bellrcrank. Short - KIT Long 31541 3x6mm FHCS :: Rear Suspension Build - Bag 3.1, 3.
PAGE 10
:: Rear Suspension Build - Bag 3.1, 3.2 - Step 2 1 4728 Rear Pod Link 2 4726 Pivot Brace ! ! #1 - Install Pivot brace to chassis. #2 - Slide rear pod into pivot brace. 4637 x2 FT Pivot Ball 31541 x2 3x6mm FHCS 7186 x2 2x6mm SHCS Use #7186 SHCS to adjust for free ball movement. ! Build two! :: Rear Suspension Build - Bag 3.1, 3.
PAGE 11
:: Rear Suspension Build - Bag 3.1, 3.2 - Step 5 31531 x2 3x6mm BHCS 31550 FT Aluminum M3 Locknut, Blue 31531 x2 3x6mm BHCS 8633 Shock Mount 8634 x2 Shock Mount Standoff 25201 3x8mm FHCS :: Rear Suspension Build - Bag 3.1, 3.2 - Step 6 Kit Setup: Note position of shock mount. Battery Forward Battery Back - Kit Refer to the image to the right for the battery forward configuration of the Shock Mount assembly.
PAGE 12
:: Rear Axle Build - Bag 4.1, 4.2 - Step 2 8648 RC10F6 Wheel Hub, Left 8691 x2 2.5x12mm SHCS 4735 Rear Axle Thrust Bearing Setup: Note orientation! 6619 x12 FT Carbide Diff Balls, 1/8” ! Tighten #89216 M4 Locknut so the spur gear does not slip! 8646 RC10F6 Wheel Hub, Right 636 se #6 rea eg n o ic 10.00 ac # 6 k 588 gr ea se Sil 8682 x3 FT Bearing 1/4”x1/8” 4736 Diff Thrust Cone 8683 FT Thrust Bearing (4x10mm) 4737 x2 Bellville Washer :: Rear Axle Build - Bag 4.1, 4.
PAGE 13
:: Wings / Electronics / Wheels Build - Bag 5.1, 5.2 - Step 1 31382 x2 Aluminum Ballstud Washer, 5.5x1mm ! Motor and pinion/ set screw not included! 25211 x2 3x10mm BHCS :: Wings / Electronics / Wheels Build - Bag 5.1, 5.2 - Step 2 Set The Gear Mesh: You should be able to rock the spur gear back and forth. without making the teeth of the pinion move. If the spur gear mesh is tight, then loosen the #25211 screws and move the motor away, then try again.
PAGE 14
:: Wings / Electronics / Wheels Build - Bag 5.1, 5.2 - Step 4 4674 x10 2x6mm FHCS 8678 x2 Wing SIde Panel 31531 x2 3x6mm BHCS 8678 Wing Panel, Rear Upper Kit Setup: 8678 Wing Panel, Rear Lower 8678 Wing Mount, Rear Lower :: Wings / Electronics / Wheels Build - Bag 5.1, 5.2 - Step 5 6338 Antenna and Cap 8608 Battery Retainer Kit Setup: Note position of the battery retainer position! Inline Battery Forward 8670 Antenna Mount Inline Battery Back 4675 x2 2.
PAGE 15
:: Wings / Electronics / Wheels Build - Bag 5.1, 5.2 - Step 7 ! Tires/Wheels not included! 91738 M4 Serrated Locknut, Flanged ! Do not overtighten front wheel nuts! 91560 x2 FT Bearing 5x10x4mm 89216 M4 Locknut :: Wings / Electronics / Wheels Build - Bag 5.1, 5.2 - Step 8 Painting Tips: Your F6 does not come with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent.
PAGE 16
:: OPTIONAL Forward Servo Build - Step 1 8656 RC10F6 Forward Servo Mount, Front 8656 RC10F6 Forward Servo Mount, Rear 8654 Front Top Plate Standoff (FWD Servo) 25201 x5 3x8mm FHCS 596 ck #1 d lo a e thr 81257 3x6mm Set Screw ! Build four! 3.8mm 8652 Suspension Arm Standoff, Upper :: OPTIONAL Forward Servo Build - Step 2 31531 x3 3x6mm BHCS 8658 x3 RC10F6 Caster Bushing Camber 8658 x4 RC10F6 Camber Bushing 8636 RC10F6 Front Top Plat (FWD Servo) Caster 1.0° 3° 1.5° - KIT 6° 2.
PAGE 17
:: OPTIONAL Forward Servo Build - Step 4 ! Electronics not included! 8608 x2 Battery Retainer 4675 x4 2.
PAGE 18
:: Shock 4637 5407 21139 31326 31327 31510 31687 :: Damper Tubes 31688 31693 31696 31698 31700 91493 FT Pivot Balls Red O-Rings 2.6x6mm Washers FT VCS3 Shock Collars & O-Rings FT VCS3 Shock Bottom Caps & O-Rings 2x4mm BHCS FT FOX(R) Shock Bodies w/Genuine Kashima Coat Shock Shafts Shock Rebuild Kit Shock Cap Retainers Shock Spring Cups Shock Eyelet Set FT Low Friction X-Rings 31689 31690 Shock Pistons, 3x1.1 FT Shock Pistons, 3x1.
PAGE 19
:: Chassis 1736 2230 3897 4637 4670 4675 4707 4726 4728 4790 4791 4792 4793 4794 6338 7186 8608 8620 8631 8633 8634 8642 8670 25201 31280 31384 31385 31386 31531 31532 31541 31550 FT Body Clips, Metallic Blue, Short Body Mounts Pivoting Body Mounts FT Pivot Balls 3x8mm Set Screws 2.5x6mm FHCS Side Spring Retainers Pivot Brace Rear Pod Link Side Spring, 3.9lb/in - Black Side Spring, 4.2lb/in - Green Side Spring, 4.7lb/in - Gray Side Spring, 5.2lb/in - White Side Spring, 5.
PAGE 20
:: Front Suspension 4113 4114 4116 4117 4118 4119 4670 4754 4755 6299 8441 8638 8651 8663 8667 8670 25211 25225 31283 31381 31382 31383 31384 31385 31386 31531 31541 89216 91560 King Pin Springs (.020) King Pin Springs (.018) King Pin Springs (.024) King Pin Springs (.022) King Pin Springs (.014) King Pin Springs (.
PAGE 21
:: Rear Axle 3921 3922 3923 3924 3994 4615 4616 4462 4735 4736 4737 6619 8504 8646 8648 8682 8683 8691 25225 89216 91738 Spur Gear 69T, 48P 1 Spur Gear 72T, 48P 1 Spur Gear 75T, 48P 1 Spur Gear 66T, 48P 1 Spur Gear 73T, 48P 1 Spur Gear 96T, 64P 1 Spur Gear 88T, 64P - Kit 1 Spur Gear 100T, 64P 1 Rear Axle 1 Diff Thrust Cone 1 Bellville Washer 4 FT Carbide Diff Balls, 1/8 in 8 D-Drive Rings, for Axle 2 RC10F6 Wheel Hub, Right Side 1 RC10F6 Wheel Hub, Left Side 1 FT Ball Bearing, .250x.375x.
PAGE 22
:: Reedy Electronics 252C 253C 254C 255C 256C 258C 259C 260C 261C 262C 269C 270C 284C 285C 287C 27002 27003 27004 27005 27024 27026 27027 27028 27029 27030 27108 27109 27124 27125 27126 27127 29193 29194 Blackbox 800Z/540-M3 25.5 Combo Blackbox 800Z/540-M3 21.5 Combo Blackbox 800Z/540-M3 17.5 Combo Blackbox 800Z/540-M3 15.5 Combo Blackbox 1000Z+/540-M3 10.5 Combo Blackbox 1000Z+/540-M3 8.5 Combo Blackbox 1000Z+/540-M3 8.0 Combo Blackbox 1000Z+/540-M3 7.5 Combo Blackbox 1000Z+/540-M3 7.
PAGE 23
:: Pinions 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 17T 18T 19T 20T 21T 22T 23T 24T 25T 26T 27T 28T 29T 30T 31T 32T 33T 34T 35T 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P 48P :: Lubes & Adhesives / Misc.
PAGE 24
KIT SETUP Driver: Date: Track: Event: Qualify: TQ: Main: Finish: Best Lap Time: Track Info: Size: Small Large Medium X-Large Surface: Carpet Indoor Asphalt Outdoor Traction: Low High Medium Wet Condition: Bumpy Smooth Temperature: Ambient Track FWD Servo: Droop: Ride Height: Shim: 0.5mm Notes: Fixed: Floating: STD Servo: Ride Height: 0 Shim: Droop: Shim: 0.5mm Ride Height: 1.0° 1.5° 2.0° 2.
PAGE 25
Driver: Date: Track: Event: Qualify: TQ: Main: Finish: Best Lap Time: Track Info: Size: Small Large Medium X-Large Surface: Carpet Indoor Asphalt Outdoor Traction: Low High Medium Wet Condition: Bumpy Smooth Temperature: Ambient Track FWD Servo: Droop: Ride Height: Shim: Notes: Fixed: Floating: STD Servo: Ride Height: Shim: Droop: Ride Height: 1.0° 1.5° 2.0° 2.
PAGE 26
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.RC10.com https://twitter.com/Team_Associated https://www.instagram.com/teamassociatedrc/ https://www.facebook.com/TeamAssociated/ call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.