AssociatedElectrics.
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RTR. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets. :: KIT Features • Based on the 9-time R.O.A.R.
:: Hardware - 1:1 Scale View Button Head (bhcs) Flat Head (fhcs) 2x4mm (31510) Aluminum (8545) 3x8mm (25201) Aluminum (8553) Titanium (91592) 2.5x8mm (31521) 3x8mm (31532) Aluminum (8552) Titanium (91581) 10x15x4 (91563) Ballstuds HD 6mm (91047) Titanium HD 6mm (91751) Set Screws 3x3mm (25225) Shims and Washers 3x26mm (89205) FT Ballstud Washer, Aluminum (0.5mm) (31381) FT Ballstud Washer, Aluminum (1mm) (31382) Cap Head (shcs) 2.
:: Table of Contents 1................... Cover 13 - 14........Gearbox Install 2................... Introduction 14 - 15........Rear Hub and CVA Build 3...................1:1 Hardware “Fold Out” 15 - 16........ Turnbuckles Build 4................... Table of Contents 16 - 17.........Shocks Build 5 - 7..............Quick Start Guide 18 - 20........Electronics Build 8....................Front Top Plate and Steering Build 20 - 21........Bumpers and Chassis Braces Build 9 - 10...........
2/20 :: Quick Start Guide Battery Charging Steps and Safety: Remove the battery from the vehicle before charging. Place battery on a fire resistant surface. Avoid any contact with water or other liquids. Be sure to select the correct charging mode for the type of battery you are charging. ALWAYS use a compatible charger for charging your batteries. Caution: Never leave the battery unattended while charging. Always disconnect the charger from the power source when finished charging.
:: Quick Start Guide - (cont.) Battery Notes and Tip: Connect the battery as shown. Disconnect the battery when not in use! LiPo: LiPo batteries (lithium polymer) are high current rechargeable batteries. LiPo batteries offer extended run time and peak performance over NiMH batteries. They require a peak detection charger designed specifically for LiPo batteries. These batteries require special care and handling.
:: Quick Start Guide - (cont.) Radio System Tuning and Controls: DO NOT hold the trigger when turning on the radio. If using optional battery for transmitter, be sure to plug it in correctly. Plugging in a battery backwards can cause damage. Refer to Radio owners manual for more in-depth instructions on radio operation and functions. Adjust steering trim so front wheels point straight. Push trigger for Brake Pull trigger for Throttle Neutral Throttle set to Neutral! :: Quick Start Guide - (cont.
:: Front Top Plate and Steering Build - Step 1 91047 x2 Heavy-duty Ballstud, 6mm 91475 x4 3x7x3 Ball Bearing 91391 Steering Rack ! Note orientation of steering rack. 91391 x2 Steering Rack Crush Tube 91391 Steering Bellcrank Brace 89202 x2 M3 x 12mm BHCS ! Do not overtighten steering bolts. Make sure there is free movement in the steering rack. :: Front Top Plate and Steering Build - Step 2 ! Note orientation of the brace.
:: Front Suspension Build - Step 1 31530 M3 x 5mm BHCS 91047 Heavy-duty Ballstud, 6mm 96 #15 lock d a e thr 91417 Steering Block 25237 x2 5 x 10 x 4 Bearing 91048 Heavy-duty Ballstud, 8mm 91402 x2 Caster Block Bushing 91417 Caster Block 25215 M3 Locknut, black 71127 Front Axles Build 2 (1 left, 1 right) 89202 x2 M3 x 12mm BHCS :: Front Suspension Build - Step 2 71068 Front Arms 31509 x2 M2 x 3mm BHCS 6 59 ck #1 lo ad e r th 91394 Hinge Pin (front, outer) 31509 x2 M2 x 3mm BHCS 25211 x2 M3
:: Front Suspension Build - Step 4 71066 x2 Front Body Post Reakt Body Trim Post 71032 x2 M2.5 x 14mm SHCS 89202 x4 M3 x 12mm BHCS :: Rear Suspension Build - Step 1 31521 M2.
Front Suspension Shock Tower and -Bumper :: Rear Build Step 3 Build - Bag C - Step 3 89204 x2 M3 x 24mm BHCS 91477 x2 M3 Nut (Black) 25211 x2 M3 x 10mm BHCS 25187 x2 M3 x 14mm BHCS 71003 Rear Shock Tower :: Rear Gear Shock Diff Build Tower - Step and 1 Bumper Build - Bag D - DD - Step 1 91466 Gear Diff Gear 91463 Gear Diff O-Ring (Large) 91463 x2 Gear Diff Washer 91463 Gear Diff Sun Gear 91463 Gear Diff O-Ring (Small) 91463 x4 Gear Diff Planet Washer 91463 x4 Gear Diff Planet Gear 91465 Gear D
:: Gear Diff Build - Step 3 31350 x4 M2.5 x 10mm FHCS #6588 e greas 91463 Gear Diff Gasket black ! * Ensure free outdrive rotation before installation! :: Gearbox Build - Step 1 91430 Gearbox (right & left) 91466 Idler Gear 91563 x2 10 x 15 x 4, Bearing 25237 x2 5 x 10 x 4, Bearing 91132 Idler Gear Shaft 25237 x2 5 x 10 x 4, Bearing :: Gearbox Build - Step 2 ! Add a drop of Diff Lube (#6591) to the teeth of the diff gear, idler gears, and top shaft.
:: Gearbox Build - Step 3 91478 x2 M3 x 30mm FHCS 71038 x2 Body Mount Brace (Left & Right) 89225 M3 x 24mm SHCS 71070 x2 Wheelie Bar Mount 25215 M3 Locknuts 91428 Motor Plate, Blue 25202 x3 M3 x 10mm FHCS :: Slipper Build - Step 1 9611 x2 Slipper Pad 7485 x2 FT V2 Slipper Hub 91423 Slipper Spring Adapter 9654 Spur Gear 87T, 48P :: Gearbox Install - Step 1 ! The Locknut should be flush with the top shaft when installed.
:: Gearbox Install - Step 2 25211 x2 M3 x 10mm BHCS 25203 x2 M3 x 12mm FHCS :: Gearbox Install - Step 3 25202 x4 M3 x 10mm FHCS 25204 x2 M3 x 16mm FHCS 71066 x2 Rear Body Pivot 71038 Rear Body Mount 71066 x2 Rear Body Post REAKT 71032 x4 M2.
:: Rear Hub and CVA Build - Step 2 91436 CVA Wheel Hex Pin 91418 Wheel Hex (rear) 31509 M2 x 3mm BHCS Build x2 (right and left side) 91394 Hinge Pin (rear, outer) :: Turnbuckles Build - Step 1 91469 Ball Cup ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! Racers Tip: Use black grease (#6588) on the threads of the turnbuckles for easier ball cup installation! 91723 Turnbuckles, 3x48mm 91469 Ball Cup Steering Turnbuckle 27.
:: Turnbuckles Build - Step 3 91469 Ball Cup ! 91723 Turnbuckles, 3x48mm 91469 Ball Cup Rear Camber Turnbuckle Racers Tip: Use black grease (#6588) on the threads of the turnbuckles for easier ball cup installation! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! 23.50mm Build x2 (right and left side) :: Shocks Build - Step 1 91444 12mm Shock Piston 6299 1/8 E-Clip 6299 1/8 E-Clip 91489 3 x 27.
:: Shocks Build - Step 3 id flu k 2 oc 42 h S #5 91454 Shock Cap (Molded) Sh oc #5 k flu 42 id 2 Shock Bleeding Steps: 1. 2. 3. Front/Rear Shock: 30wt 4. 5. 6. 7. 8. 9. 10. 11. 12. Step 1-3 Step 3-4 Step 5-6 Step 7 Pull shock shaft down. Fill shock body 3/4 full with silicone fluid. Slowly move the shock shaft up and down to remove air from under piston. Wait for bubbles to come to surface. Fill shock body to top with silicone fluid. Place a drop of oil in the cap and on cap threads.
:: Electronics Build - Step 1 91047 Heavy-duty Ballstud, 6mm ! 71047 Servo Saver Align the servo horn 90 degrees. Adjust steering trim once vehicle is complete. 91469 Steering Link 25201 M3 x 8mm FHCS Servo :: Electronics Build - Step 2 91391 x2 Servo Mount 31532 x4 M3 x 8mm BHCS 25201 x2 M3 x 8mm FHCS 7337 x4 Gold Washer :: Electronics Build - Step 3 31530 x2 M3 x 5mm BHCS Motor ! 1336 Pinion Gear, 18T, 48P See page 23 for gear mesh setting instructions! 7337 x2 .250x.125x.
:: Electronics Build - Step 4 71023 Receiver Box Grommet ! * Install the ESC wires and the Servo wires into the wire grommet before installing the grommet into the receiver box! 71023 Wire Grommet Plug ! * Receiver grommet plug can be removed if you use a personal transponder! :: Electronics Build - Step 5 71023 Receiver Box Plug and Grommet 25211 M3 x 10mm BHCS Receiver 6727 Servo Tape 71023 Receiver Box Seal 71026 Receiver Box :: Electronics Build - Step 6 6338 Antenna Tube & Cap 25225 M3 x
:: Electronics Build - Step 7 :: Bumpers and Chassis Braces Build - Step 1 Battery not included! 25203 x2 M3 x 12mm FHCS 71067 Front Bumper Brace 71048 Battery Foam Spacer 71067 Front Bumper 89202 x2 M3 x 12mm BHCS :: Bumpers and Chassis Braces Build - Step 2 71071 Wheelie Bar Arm (Left) 25215 M3 Locknut 71070 Wheelie Bar Flange Shaft 25204 x2 M3 x 16mm FHCS 31734 x2 M5x10x3mm Bearing 71070 Wheelie Bar Wheel (22mm) 89203 M3 x 16mm BHCS Build x2 (right and left side) :: Bumpers and Chassis Br
:: Bumpers and Chassis Braces Build - Step 4 25211 x4 M3 x 10mm BHCS 71067 Nerf Bar :: Tires and Body Build - Step 1 71078 Wheel, Rear 71079 Wheel, Front 71072 Pre Glued Wheel/Tire, Rear ! Clean the tire and wheel bead. Carefully apply CA glue (tire adhesive) to the tire bead on both sides.
:: Tires and Body Build - Step 3 71082 Reakt Drag Body, Clear 31520 x4 M2.5x6mm BHCS 25215 x4 M3 Locknut :: Tires and Body Build - Step 4 31520 x2 M2.
:: Tires and Body Build - Step 5 :: Tuning Tips Tips for Beginners: Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps. Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change.
:: Tuning Tips (cont.) Slipper Clutch: The assembly instructions give you a base setting for your clutch. Turn the nut on the shaft so that the end of the top shaft is flush with the nut. At the track, tighten or loosen the nut in 1/8 turn increments until you hear a faint slipping sound for 1-2 feet on takeoffs. Another popular way to set the clutch is to hold both rear tires firmly in place and apply short bursts of throttle.
:: Shock Springs :: Shocks 5407 6299 31327 71051 71054 91444 91454 91469 91489 91491 Red O-Rings E-Clip FT VCS3 Shock Bottom Caps Shock Body 12 x 27.5mm Spring Clips and Retainer Shock Accessories Set Shock Caps and Spring Cups Shock Pivot Ball and Rod End 27.5 x 3MM Shock Shaft 12MM V2 Shock Rebuild Kit 8 12 2 2 1 1 4 ea. 4 2 1 91635 12mm Front Spring (54mm) GRN 3.75 91636 12mm Front Spring (54mm) WHT 4.10 91637 12mm Front Spring (54mm) GRY 4.
:: Transmission 7337 25202 25203 25211 25237 31532 89203 91132 91428 91430 91431 91466 91563 91606 .250x.125x.015” Washer M3 x 10mm FHCS M3 x 12mm FHCS M3 x 10mm BHCS Bearing, 5 x 10 x 4 M3 x 8mm BHCS M3 x 16mm BHC 4x4 Idler Gear Shaft Motor Plate (Blue), B5 Gearbox Gear Cover / Motor Guard Diff and Idler Gear FT Bearing, 10 x 15 x 4 Aluminum Top Shaft V2 10 10 10 10 2 10 10 1 1 Pr.
:: Optional Ball Differential 6573 6574 6575 6581 6582 7666 7677 31400 91419 91420 Diff Thrust Washer & Bolt Precision Diff Thrust Balls, 5/64” Locking T-Nut, Diff Thrust Bolt, & Cover 3/32” Carbide Diff Balls Diff Thrust Spring Diff Drive Rings, 2.60:1 Ball Diff Rebuild Kit Bearing, 5 x 8mm Diff Gear, B5 Ball Diff Outdrive, B5 2 6 1 14 1 2 1 2 1 1 ea.
Steering :: FrontBlock, Arm Hex 25189 25215 25237 31509 31530 71068 71127 89202 91047 91048 91394 91402 91417 91738 M3 x 22mm BHCS M3 Locknut, Black Bearing, 5 x 10 x 4 M2 x 3mm BHCS M3 x 5mm BHCS Suspension Arm Set Front Axle M3 x 12mm BHCS Heavy-duty Ballstud, 6mm Heavy-duty Ballstud, 8mm Hinge Pin Set, B5 Caster Block Bushing, B5 Caster and Steering Blocks M4 Serrated Nuts, Black 10 20 2 10 10 1 2 10 10 10 1 4 Pr.
:: Battery Strap 71048 71050 Battery Foam Hook and Loop Straps 1 2 71050 71050 71048 :: Front Bumper 25203 25204 71067 89202 M3 x 12mm FHCS M3 x 16mm FHCS Front Bumper and Nerf Bars M3 x 12mm BHCS 10 10 1 10 25203 71067 25203 71067 89202 89202 25204 25204 :: Wheelie Bar 25215 31734 71070 71071 89202 89203 89225 89279 M3 Locknuts, Black M5x10x3mm Bearings Wheelie Bar Mount and Wheels Wheelie Bar Set M3x12mm BHCS M3x16mm BHCS M3x24mm SHCS M3x45mm SHCS 10 4 1 1 10 10 10 10 89202 89202 25215
:: Front Shock Tower 21173 25201 25612 31383 71003 71032 71066 89202 89205 91049 91444 91477 Small Body Clips M3 x 8mm FHCS M3 Locknut, with flange Ballstud Washer, 5.5 x 2mm, Blue Aluminum Pro SC10 Shock Tower Set M2.
:: Chassis Antenna Tube & Cap (black) M3 x 14mm BHCS M3 x 12mm FHCS M3 x 16mm FHCS M3 x 10mm BHCS M3 x 3mm Set Screw Ballstud Washer, 5.5 x 2mm, Blue Aluminum M2 x 3mm BHCS M2.
:: Reedy Batteries and Chargers :: Factory Team and Option Parts 1408 1409 1736 7495 25392 27128 31381 31382 31383 71014 71019 91177 91178 91179 91383 91385 91387 91389 91392 91447 91464 91492 91493 91495 91548 91550 91553 91560 91562 91563 91577 91579 91580 91581 91582 91583 91584 91585 91588 91589 91592 91593 91594 91595 91596 91597 91609 91610 91619 91620 91623 91624 91626 91627 91628 91630 91631 91633 FT Ti Turnbuckle, 2.65”/67mm (blue) FT Ti Turnbuckle, 1”/25.
:: Tools :: Reedy Motors 280 281 293 294 295 297 27400 27401 27402 27403 27404 27414 27415 27416 27417 27418 27420 27421 27428 27429 27435 27436 27437 27438 27439 27440 27441 27442 27444 27445 27446 27447 27448 27449 27450 27451 27452 27453 27454 27455 27456 27459 27460 Sonic 540-M3/M4 Rotor Spacer Set Sonic 540-M3/M4 Case Screws w/Insulator Sonic 540 FT 17.5 Fixed Timing Sonic 540 FT 13.5 Fixed Timing Sonic 540-FT Spec Rotor 12.0 x 7.25 x 25.3 Sonic 540 FT 21.5 Fixed Timing S-Plus 25.5 Spec S-Plus 21.
