User Manual

ManualsBrandsTeam Associated ManualsHobby1/10 RC10B6D 2WD Buggy Team Kit

#90012 RC10B6D Team Kit

Summary of content (34 pages)

PAGE 1
#90012 RC10B6D Team Kit
PAGE 2
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new vehicle. Please take a moment to read through the manual and familiarize yourself with the steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.
PAGE 3
:: Hardware - 1:1 Scale View Button Head (bhcs) Flat Head (fhcs) 2x4mm (31510) Aluminum (8545) 3x8mm (25201) Aluminum (8553) Titanium (91592) 2.5x6mm (31520) 3x4mm (91158) 3x6mm (31531) Aluminum (8550) Titanium (91580) 3x18mm (89209) Titanium (91597) 3x3mm (25225) 3x10mm (4671) Ballstuds Silver 8mm long (31284) Ti Nitride 8mm long (31292) HD 6mm (91047) Ti Nitride HD 6mm (91118) Shims and Washers 3x18mm (2308) Servo Mount Washer (7337) (.250 x .125 x .
PAGE 4
:: Table of Contents 1................... Cover 14.................Bags 18 - 19 2................... Introduction 14 - 16........ Bags 20 - 22 3...................1:1 Hardware “Fold Out” 16.................Bag 23 4................... Table of Contents 17 - 19.........Bags 24 - 26 5....................Bag 1 19 - 21....... Tuning Tips 5 - 7..............Bags 2 - 4 22 - 30....... Catalog 7 - 8..............Bags 5 - 8 31................ Notes / Contact Info 8 - 9..............
PAGE 5
8/16 :: Bag 1 - Step 1 31286 x2 FT Ballstud Washer, Aluminum (2mm) ! Note orientation of steering rack. Front 91667 Steering Bellcrank (Right) 91475 x4 3x7x3 Ball Bearing 91475 x4 3x7x3 Ball Bearing 91667 Steering Rack 31286 x2 FT Ballstud Washer, Aluminum (1mm) 91048 x2 Heavy-duty Ballstud, 8mm 91667 Steering Bellcrank (Left) :: Bag 1 - Step 2 ! The steering bellcrank brace has offsets on one side. They should be installed towards the bearings.
PAGE 6
:: Bag 2-4 - Step 2 91652 Side Rails (L & R) 31284 8mm Ball Stud, Long 31286 FT Ballstud Washer, aluminum (2mm) Servo screw not included! 25202 x4 M3 x 10mm FHCS Servo not included! 89009 Servo Horn Ring 9180 Servo Horn 25201 x6 M3 x 8mm FHCS :: Bag 2-4 - Step 3 91724 Steering Link, B6 A - Airtronics F - Futaba H - Hitec J - JR 91719 x2 Servo Mount 31286 FT Ballstud Washer, aluminum (1mm) Printed here ! 4671 M3x10mm Set Screw 91719 x2 Servo Spacers ! Align the servo horn 90 degrees Tighten
PAGE 7
:: Bag 2-4 - Step 5 89202 x2 M3 x 12mm BHCS ! The front hinge pin brace has a sharp edged side, and a rounded edge side. Mount the sharp edge side towards the bulkhead.
PAGE 8
:: Bag 5-8 - Step 2 91049 Heavy-duty Ballstud, 10mm 31532 x2 M3 x 8mm BHCS 91675 Caster Block 25215 M3 Locknut, black ! There are three caster block inserts included (0°, +/- 2.5 °, +/- 5 °). +5 ° is the standard insert used. Tab up = positive caster Tab down = negative caster You can install an optional #31520 screw to use as a steering stop setting.
PAGE 9
:: Bag 9-10 - Step 2 91692 Rear Gearbox Brace 91695 x2 Rear Arms 91670 Hinge Pin (rear, Inner) 91685 Rear Bumper 25204 x2 M3 x 16mm FHCS 91692 Arm Mount, D :: Bag 11-14 - Step 1 6581 x14 3/32 carbide diff balls 1 #659 lube diff 7666 Diff Drive Ring #65 91 dif f lu be 91419 Diff Gear, 52T 7666 Diff Drive Ring #65 91 dif f lu be 91701 Ball Diff Outdrive 91701 Ball Diff Outdrive :: Bag 11-14 - Step 2 6573 x2 Diff thrust washer #6588 black grease 6574 x6 5/64 diff thrust balls 6573 Diff thrust
PAGE 10
:: Bag 11-14 - Step 3 6575 Locking t-nut ! As you tighten the diff bolt, you will notice the T-nut ears moving closer to the bottom of the outdrive slot. This compresses the spring behind the T-nut. The spring should be completely compressed at the time the T-nut reaches the end of the slot. Caution! Pay close attention to the feeling when the spring is completely compressed. Do not overtighten the bolt. When you feel the spring completely compressed, loosen the diff bolt 1/8” of a turn.
PAGE 11
:: Bag 11-14 - Step 6 9603 x2 Slipper Pad 7485 x2 FT V2 Slipper Hub 91713 Stand-up Motor Plate 25202 x3 M3 x 10mm FHCS ! There’s also a 72T 48P spur gear (#9649) included for stock motor use! 9652 78T 48P Spur Gear :: Bag 11-14 - Step 7 ! 9739 Slipper Spring 91423 Slipper Spring Adapter 91148 M4 Locknut, with flange and knurl Set nut flush with top shaft.
PAGE 12
:: Bag 15-16 - Step 1 91563 10 x 15 x 4 Bearing 91697 Rear Hub Link Insert 25215 M3 Locknut, black Rear Hub Link Setting: 91698 Rear Hub Link Nut 89218 3 x 8mm Washer Up 91697 Rear Hub 91049 Heavy-duty Ballstud, 10mm th #1 re 59 ad 6 lo ck 91697 Rear Hub Insert (0) Build x2 (right and left side) 91562 6 x 13 x 5 Bearing Down Insert A B D E C C E D B A 0/3 up 0/3 down 1/2 up 1/2 down Axle Height 0 (low) + 3mm + 1mm + 2mm Recommended Ballstud location :: Bag 15-16 - Step 2 91438
PAGE 13
:: Bag 17 - Step 1 91722 Ball Cup Racers Tip: ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! Use black grease (#6588) on the threads of the turnbuckles for easier ball cup installation! 91723 Turnbuckle 3x48mm 91722 Ball Cup Steering Turnbuckle 28.75mm Build x2 (right and left side) :: Bag 17 - Step 2 91722 Ball Cup 91723 Turnbuckle 3x48mm 91722 Ball Cup Front Camber Turnbuckle 22.
PAGE 14
:: Bag 18-19 - Step 1 91533 x2 Shock Bushing, Short 25188 x2 M3 x 20mm BHCS 25203 x4 M3 x 12mm FHCS 91661 Front Shock Tower, Flat :: Bag 18-19 - Step 2 91665 Rear Shock Tower 91720 x2 Shock Bushing, Long 91718 x2 Rear Wing Mount 89202 x4 M3 x 12mm BHCS 89202 x4 M3 x 12mm BHCS 89204 x2 M3 x 24mm BHCS :: Bag 20-22 - Step 1 91634 12mm V2 Shock Piston (1.6 front) (1.7 rear) 91615 V2 3 x 21 Shock Shaft TiN (front) 91619 V2 3 x 27.
PAGE 15
:: Bag 20-22 - Step 2 91491 12mm Shock Cap O-Ring 91480 12x23mm V2 Shock Bodies (front) 91481 12x27.5mm V2 Shock Bodies (rear) ! ! Lightly rub shock oil on the o-ring before installation! 5 e 10 lim #1 n s ee gr 91721 Shock Eyelet Front Shocks - Long Rear Shocks - Long 31327 VCS3 Shock Bottom Cap O-Ring 91493 x2 X-Ring Racers Tip: #11 0 en 5 slim e 91495 V2 Shock Spacer gre 91495 x2 V2 Shock Hat Bushing There is a short and long shock eyelet.
PAGE 16
:: Bag 20-22 - Step 5 ! Use outside hole in front arm! 91447 Shock Bushing 91447 Shock Bushing 25188 M3 x 20mm BHCS Build x2 (right and left side) 25612 M3 Locknut w/Flange 25612 M3 Locknut w/Flange ! 25187 M3 x 14mm BHCS Use inside hole in rear arm! :: Bag 23 - Step 1 Motor not included! 89218 x2 M3 x 8mm Washer 31532 x2 M3 x 8mm BHCS :: Bag 23 - Step 2 ! See page 20 for gear mesh setting instructions! 31531 x2 M3 x 6mm BHCS Pinion / Setscrew not included! 91089 Belt Cover Cap 91712
PAGE 17
:: Bag 24-26 - Step 1 6338 Antenna Tube & Cap 25225 M3 x 3mm Set Screw ESC not included! Receiver not included! 6727 Servo Tape 6727 Servo Tape ! There are two options for mounting your antenna.
PAGE 18
:: Bag 24-26 - Step 4 89218 x2 3 x 8mm Washer 91731 Battery Strap, B6 91729 x2 Thumb Screw, B6 25211 x2 M3 x 10mm BHCS 91731 x2 Battery Strap Nut, B6 :: Bag 24-26 - Step 5 25203 x2 M3 x 12mm FHCS 91718 Wing Button x2 91741 Wing, B6 Body Trimming / Mounting: There are 3 body trimming options depending on what transmission and shock position you choose to run. Cut Line A: Laydown Transmission / Rear Shocks mounted in rear of arm.
PAGE 19
:: Bag 24-26 - Step 7 91738 M4 Serrated Nut, with Flange Build 2 (1 left, 1 right) 91738 M4 Serrated Nut, with Flange Build 2 (1 left, 1 right) :: Painting Tips Your B6 Team Kit comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the INSIDE thoroughly with warm water and liquid detergent (do not use any detergents with scents or added hand lotion ingredients!). Dry the body using a clean, soft, lint-free cloth.
PAGE 20
:: Tuning Tips (cont.) Motor Gearing: Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your motor and electronic speed control manufacturers for more information.
PAGE 21
:: Tuning Tips (cont.) Rear Camber Link: Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the rear chassis brace. Shortening the camber link (or lowering the ball end) will give the rear end less roll and the car will tend to accelerate or “square up” better. Lengthening the camber link (or raising the ball end) will give the rear more roll and more cornering grip.
PAGE 22
:: Shocks 4187 31327 31510 89278 91304 91310 91449 91480 91481 91491 91492 91493 91495 91615 91619 91634 91721 :: Ball Differential .030 Nylon Washer VCS3 Shock Bottom Cap and O-Ring 2x4mm BHCS 2.5mm Washer 12MM Threaded Collar and O-Ring 12MM Shock Spring Cups (+0mm, +5mm, +9mm) 12MM V2 Composite Shock Cap w/O-ring and bleeder screw 12x23MM V2 Shock Bodies 12x27.
PAGE 23
:: Transmission 25187 25202 25203 31286 31532 89218 91048 91132 91560 91563 91692 91693 91706 91709 91710 91713 91717 M3 x 14mm BHCS M3 x 10mm FHCS M3 x 12mm FHCS Ball Stud Washers, Alum. (1mm, 2mm) M3 x 8mm BHCS 3 x 8mm Washer Heavy-duty Ballstud, 8mm FT 4x4 Idler Gear Shaft FT Bearings, 5x10x4mm FT Bearings, 10x15x4mm Rear Gearbox Brace, B6 Rear Ball Stud Mount, B6 Stand-up Gear Box Chassis Brace, B6 Top Shaft, B6 Stand-up Motor Plate, B6 Idler Gear, 26T 20 20 20 4 ea. 6 10 8 2 4 4 1 1 Pr.
PAGE 24
:: Optional Gear Differential 4675 9831 91462 91463 91464 91465 91605 91703 5450 5451 5452 5444 5453 5446 5454 5455 5466 5456 5457 5458 5448 5459 5461 5463 5465 M2.
PAGE 25
:: Front Arm 25187 25188 25215 31286 31510 31531 31532 91048 91049 91560 91670 91671 91675 91676 91677 91679 91682 91738 M3 x 14mm BHCS M3 x 20mm BHCS M3 Locknut, Black FT Ballstud Washer, aluminum (1mm, 2mm) M2 x 4mm BHCS M3 x 6mm, BHCS M3 x 8mm, BHCS Heavy-duty Ballstud, 8mm Heavy-duty Ballstud, 10mm FT Bearing, 5 x 10 x 4 Hinge Pin Set, B6 Front Arm, Flat, B6 Caster Block, B6 Caster Hat Bushing, B6 (0mm, 1mm, 2mm, 3mm) Steering Block, B6 Steering Block Arm, B6 Front Axle, B6 M4 Serrated Nut w/ Flange
PAGE 26
:: Front Shock Tower 25188 25203 25612 91447 91533 91661 M3 x 20mm BHCS M3 x 12mm FHCS M3 Locknuts w/Flange Shock Bushing Balls Shock Bushings, Short w/Balls Front Tower, Flat, B6 20 20 20 4 4 ea. 1 91533 91447 25612 25188 25203 91533 91447 91661 25203 :: Rear Shock Tower 25203 25612 89202 89204 91447 91665 91718 91720 M3 x 12mm FHCS M3 Locknuts w/Flange M3 x 12mm BHCS M3 x 24mm BHCS Shock Bushing Balls Rear Tower, B6 Wing / Body Mount Set, B6 Shock Bushing & Ball, B6 20 20 10 10 4 1 1 4 ea.
PAGE 27
:: Front Bulkhead / Steering 25188 25204 25225 31283 31286 89202 91048 91049 91475 91654 91655 91656 91667 91685 M3 x 20mm BHCS M3 x 16mm FHCS M3 x 3mm Set Screw Ball Studs, Long, 5mm FT Ball Stud Washer, aluminum (1mm, 2mm) M3 x 12mm BHCS Heavy-duty Ballstud, 8mm Heavy-duty Ballstud, 10mm 3x7x3 Ball Bearing Top Plate, B6 Front Ball Stud Mount, B6 Bulkhead, B6 Steering Assembly, B6 Bumpers, B6 20 20 20 6 4 ea. 25188 91667 10 8 8 8 1 1 1 1 1 ea.
PAGE 28
:: Body and Decals :: Factory Team and Option Parts 7495 31286 91175 91176 91177 91178 91179 91389 91447 91450 91492 91495 91548 91549 91550 91553 91580 91581 91582 91583 91584 91585 91588 91589 91592 91593 91594 91595 91596 91597 91609 91612 91658 91659 91663 91668 91669 91672 91673 91674 91683 91687 91688 91696 91703 91707 91708 91711 91714 91715 91716 91735 91736 91745 91746 91747 91748 91749 91750 91751 91752 91753 91755 Vented V2 Slipper Hubs FT Ballstud Washer, aluminum (1mm, 2mm) FT VTS Slipper
PAGE 29
:: Reedy Motors / Spare Parts / Accessories 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 284 285 Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 25.5 21.5 17.5 13.5 10.5 9.5 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 SS 17.5 SS 13.5 SS 21.5 SS 10.
PAGE 30
:: Tools 1111 1113 1449 1541 1545 1546 1554 1564 1567 1568 1569 1570 1590 1592 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1719 1737 3718 3719 3720 3987 6429 6956 7709 :: RePlay Cameras / Kicker Audio FT Turnbuckle Wrench 12mm Big Bore Shock Tool FT Off Road Ride Height Gauge FT Hex Driver Set, (7 pcs) FT 5/64” Blue Hex Driver FT 3/32” Gold Hex Driver FT Silver Spring Hook Tool FT 5.5mm Red Nut Driver FT 8mm Gold Nut Driver Factory Team 5.
PAGE 31
:: Notes :: Contact Information Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info! Associated Electrics, Inc. 26021 Commercentre Drive Lake Forest, CA 92630-8853 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team Associated http://bit.
PAGE 32
Driver: Team Kit Stock Setup Date: Track: Qualify: Front Suspension: Ride Height: 23mm Camber: -1° Toe: 0° Arm Type: Flat Tower Type: Flat Caster Block Insert: Bulkhead Type: Kick-Up Angle: Wheel Hex: TQ: Anti Roll Bar: 25° 5.0mm Main: Finish: 2mm Bump Steer Spacing: None White (0.8mm) Gray (0.9mm) Blue (1.
PAGE 33
Driver: Event: Date: Track: Qualify: TQ: Main: Finish: Best Lap Time: Front Suspension: Anti Roll Bar: Ride Height: Camber: Toe: Arm Type: Tower Type: Axle Height: Bump Steer Spacing: None White (0.8mm) Gray (0.9mm) Blue (1.
PAGE 34
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://bit.ly/AEonFacebook call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.